1987 MAZDA 626 timing belt

1C ASSEMBLY (TIMING BELT)
Cam (intake)
Adjust disc
Valve clearance
0.30 mm (0.012 in) 4.00 mm (0.157 in)
76G01C-201
(5) Select an appropriate disc depending on the
valve clearance measured. And install it.
Example (intake valve):
Thickness of original adjusting disc + (measured
clearance — standard clearance) = thickness of
new adjusting disc.
4.00 + (0.30 - 0.25) = 4.05 mm
0.157 + (0.012 - 0.010) = 0.159 in
Note
a) The disc thickness is indicated by the num-
ber marked on the disc. For example, 3825
means 3.825 mm (0.1056 in).
b) Adjusting discs are available in 25 different
thicknesses within the 3.40—4.60 mm
(0.134—0.181 in) range, at intervals of 0.05
mm (0.002 in).
(6) Inspect the clearance again.
4. Set the No.4 cylinder to compression TDC.
5. Measure and adjust the valve clearance at No.3,
No.4 (intake), and No.2, No.4 (exhaust) in the same
way.
76G01C-202
Gasket
Head cover Apply sealant
^ 1 §
Cylinder Head Cover
1. Apply sealant to the shaded areas.
2. Install the cylinder head cover.
Tightening torque:
7—10 Nm (70—100 cm-kg, 61—89 in-lb)
3. Install the PVC hose.
76G01C-203
1C—86

OIL PUMP 2A
OIL PUMP
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts. 76G02A-015
DOHC
76G02A-016
1. Timing belt (Refer to Section 1B) 4. Timing belt pulley
2. Oil pan (Refer to page 2A—7.) 5. Oil pump
3. Timing belt pulley lock bolt
2A-9

2A OIL PUMP
SOHC
1. Timing belt (Refer to Section
1
A)
2. Oil pan (Refer to page 2k—1)
3. Timing belt pulley lock bolt
76G02A-017
4. Timing belt pulley
5. Oil pump
Removal Note
Timing belt pulley lock bolt
Hold the timing belt pulley with the SST and remove
the lock bolt.
76G02A-026
2 A—10

2B OIL PUMP
OIL PUMP
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G02B-026
6. Oil pan (Refer to page 2B—9)
7. Stiffener (RF-CX)
8. Oil strainer
9. Oil pump
Removal Note
Timing belt pulley lock bolt
Hold the timing belt pulley with the SST and remove
the lock bolt.
1. Timing belt (Refer to page 1C—11)
2. Camshaft pulley (Refer to page 1C—36)
3. Injection pump pulley (Refer to page
1C—36)
4. Seal plate
5. Timing belt pulley
2B-12

3A TROUBLESHOOTING GUIDE i
SPECIFICATIONS
^Engine model
Item ^__
FE-DOHC
FE 8-valve,
F8, F6...except
Middle East
.General
FE 12-valve
FE 8-valve F8, F6...only Middle East General

Cooling system Water cooled, forced circulation
Coolant capacity liters (US qt, Imp qt)
With heater 7.5 (7.9, 6.6) Coolant capacity liters (US qt, Imp qt) Without heater 7.0 (7.4, 6.2)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified seal
Thermostat
Type Wax, 2-stage Wax
Thermostat
Opening temperature °C(°F) Sub
.
83.5-86.5 (182-188) Main: 86.5-89.5 (188-193) 86.5-89.5 (188-193) 80.5-83.5 (177-182) Thermostat
Full-open temperature °C(°F) 100 (212) 95 (203)
Thermostat
Full-open lift
mm
(in) Sub: 1.5 (0.06) min.
Main: 8.0 (0.31) min. 8.5 (0.33) min.
Radiator
Type Corrugated
Radiator Cap valve opening pressure
kPa (kg/cm2, psi) 74-103 (0.75-1.05, 11-15)
Cooling
fan

Capacity
W

MTX 80
Cooling
fan

Capacity
W
ATX 120
Cooling
fan
Number
of
blade 4 Cooling
fan

Outer diameter
of
blade
mm
(in) MTX 320 (12.6)
Cooling
fan

Outer diameter
of
blade
mm
(in)
ATX 340 (13.4)

76G03A-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3A—
5

Coolant leakage Repair
—

Radiator fins clogged Clean 3A—
7

Radiator cap malfunction Replace 3A-
6

Cooling fan malfunction Repair 3A-12 Thermostat malfunction Replace 3 A-11
Water passage clogged Clean 3A—
5

Water
DumD
malfunction ReDair
or
replace 3A-
8
Corrosion
Impurities
in
coolant Replace 3A-
5
76G03A-004
3A—4

3A WATER PUMP
WATER PUMP
REMOVAL
1. Disconnect the negative battery cable.
2. Turn the crankshaft so that the No. 1 cylinder is at TDC of compression.
3. Drain the engine coolant.
4. Remove in the sequence shown in the figure.
1. Timing belt (Refer to Section 1B) 4. Idler pulley
2. Camshaft pulley (Refer to Section 1B) 5. Water pump
3. Seal plate 6. O-ring
3A—8

WATER PUMP 3A
SOHC
19—25 N m (1.9—2.6 m-kg, 14—19 ft-lb)
37—52 N m (3.8—5.3 m-kg, 27—38 ft-lb)
1. Timing belt (Refer to Section 1A)
2. Idler pulley
3. Water pump
4. O-ring
76G03A-007
3A-9

TROUBLESHOOTING GUIDE
3B

SPECIFICATIONS

Cooling system Water-cooled, forced circulation
Coolant capacity liters (US
qt,
Imp
qt)

With heater 9.5 (10.0, 8.4) Coolant capacity liters (US
qt,
Imp
qt)

Without heater 9.0 (9.5, 7.9)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified mechanical seal
Thermostat
Type Wax, two stage
Thermostat
Opening temperature °C(°F) Main Sub
Thermostat
Opening temperature °C(°F)
86.5-89.5 (188-193) 78.5—81.5 (173-179) Thermostat
Full-open temperature °C(°F) 100 (212) 100 (212)
Thermostat
Full-open lift
mm (in)
8.0 (0.31) min. 1.5 (0.06) min.
Radiator
Type Corrugated
fin

Radiator Cap valve opening pressure
kPa (kg/cm2,
psi)
74-103 (0.75-1.05, 11—15)
Cooling
fan

Type Electric
Cooling
fan

Capacity
W
120
Cooling
fan
Switching temprature orvopi OFF
- ON ^
91 (196) Cooling
fan

Number
of
blade 4
Cooling
fan

Outer diameter
mm
(in) 340 (13.4)

76G03B-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3B-
4

Coolant leakage Repair
—

Radiator fins clogged Clean 3B—
6

Radiator cap malfunction Replace 3B—
5

Cooling fan malfunction Repair 3B-11 Thermostat malfunction Replace 3B—
9

Water passage clogged Clean 3B—
4

Water pump malfunction ReDair
or
replace 3B—
7

Corrosion
Impurities
in
coolant Replace 3B-
4

76G03B-004
3B—3