1987 MAZDA 626 service

4D FUEL SYSTEM
Overhaul
Service point
1. For overhauling the injection pump, see the "Repair Service and Maintenance" manual prepared
by the manufacturer of the pump.
2. If the inside of the injection pump is disassembled for maintenance, be sure to properly use the
checking device such as the pump tester.
76G04D-068
Manufacturer of Injection Pump:
Diesel Kiki Co., Ltd.
63G04D-312
Construction of VE Injection Pump
Servo diaphragm
Boost compensation stopper
p^ ^-Fue! cut solenoid
valve
'Cold start device
63G04D-313
4D—28

4D FUEL SYSTEM
FUEL TANK
Removal and Installation
1. Drain the fuel from the fuel tank.
2. Remove in the sequence shown in the figure, referring to the removal note for the specially marked
parts.
76G04D-081
1. Fuel level gauge connector 4. Joint hose 7. Fuel tank
2. Fuel main hose 5. Ventilation hose 8. Fuel tank pad
3. Fuel return hose 6. Breather hose
Removal note
Fuel main and return hoses
1. Remove the service hole cover from the body.
2. Disconnect the fuel main and return hoses and
plug them.
Warning
Keep fire and open flame away from the fuel
area.
4D—34

TROUBLESHOOTING (G4A-EL) 7B
06 4 second period
55 4 second period
63
-*•
4 second period
Repeats above
General Note
1. If there is more than one malfunction, the code
numbers will be displayed on the tester one by one
in a numerical order. In the case of malfunctions,
55, 06, and 63, the code numbers are displayed
in an order of 06, 55, then 63. The display is as
shown.
86U07B-018
When the service connector
is not grounded
Malfunctions YES
NO
Hold indicator YES
flashing NQ
YES
NO
Memory in control unit
2. The hold indicator flashes to indicate the same pat-
tern as the buzzer of the EC-AT Tester when the
EC-AT service connector is grounded.
When the EC-AT service connector is not ground-
ed, the indicator flashes in a constant frequency
while a malfunction is occurring and goes out
if
the
malfunction recovers. However, the warning code
is memorized in the EC-AT control unit.
76G07B-015
Sensors-
Solenoid-valve
Fail-safe program Proces--\Out sing -v puts
The EC-AT control unit has a built-in fail-safe func-
tion for the throttle sensor, the pulse generator, and
the 1-2, 2-3, and 3-4 shift solenoid valves.
If a malfunction occurs, the EC-AT control unit will
control operation of the remaining components ac-
cording to a preset fail-safe program.
The vehicle may still be driven, although the driv-
ing performance will be slightly affected.
79G07C-062
4. The memory of warning codes is canceled by dis-
connecting the negative battery terminal for ap-
prox. five seconds.
79G07C-063
7B-17

7B TROUBLESHOOTING (G4A-EL)
Retrieval Procedure
1. Locate the service connector.
86U07B-019
76G07B-214

11 IDLFC
5» O | || KICK DOWNS* _ If, DEPRESS
|[BRAKE UORRSW
MNMWE STF *
° M CRUISE CONTROL SW
CDS®> *• PI ^ SPEED DROPS
Gf Aft
•
OO ou
I I
w

6019 HI NOW* XIKI
CO , LTQ
MUX
IN
JAP"
76G07B-016
2. Ground the ground connector of the EC-AT
Tester.
3. Connect the 6-pin connector of the EC-AT Tester
to the service connector.
Note
The service connector is blue-colored con-
nector.
4. Ground the 1 pin service connector.
Note
The service connector is blue-colored con-
nector.
5. Turn the ignition switch ON.
6. Check that "88" flashes on the digital display and
the buzzer sounds for three seconds after turning
the ignition switch ON.
7. If "88" does not flash, check the service connec-
tor wiring.
8. If "88" flashes and the buzzer sounds continuously
for more than 20 seconds, check wiring to 2M ter-
minal of the EC-AT control unit for short-circuit then
replace the EC-AT control unit and repeat steps
3 and 4.
9. Note the code numbers and check for the causes
by referring to the Inspection Procedure shown on
pages 7B—19 to 7B—21, repair as necessary.
Note
After repairs are made, recheck for code num-
bers by performing the "After-repair
procedure."
7B—18

TROUBLESHOOTING (G4A-EL) 7B
79G07C-068

Drive at 50
km/h
(31
mph)
Kick-down
Stop
the
vehicle
79G07C-069
After-repair Procedure
1. Cancel the memory of malfunctions by disconnect-
ing the negative battery terminal for at least five sec-
onds, then reconnect it.
2. Remove the EC-AT tester if it is connected.
3. Drive the vehicle at 50 km/h (31 mph), then de-
press the accelerator pedal fully to activate kick-
down. Stop the vehicle gradually.
KICK goimsv
BRAKE LIGHTS*
CRUISE CONTROL
C V,. DEPRESS FULL*
Ox
azsa
ORUti rpn
"J
i"
•
rm uu

£ZL ofF

4. Reconnect the EC-AT tester to the 6-pin service
connector.
5. Ground the 1 -pin service connector with a jumper
wire.
6. Turn the ignition switch ON.
7. Check that no code numbers are displayed.
79G07C-070
Inspection Procedure
No. 06 code display (Vehicle speed sensor)
76G07B-017
7B-19

FRONT DOORS 14
REMOVAL
Front Door Glass and Regulator
Note
Raise the door glass 100 mm (3.94 in) from the
fully open position.
1. Remove the clip and regulator handle.
(Manual type)
86U14X-036
Remove the inner handle cover, the screws (ar-
rows), and the door trim.
Note
For vehicles with power windows, disconnect
the connectors.
86U14X-037
3. Remove the door screen.
Caution
Remove the screen carefully so that it may be
reused.
86U14X-038
86U14X-039
4. Position the door glass so that the mounting bolts
can be removed from the service holes.
5. Remove the mounting bolts.
14—15

1 4 FRONT DOORS
86U14X-060
86U14X-040
86U14X-041
6. Remove the beltline molding. (Refer to page
14-39)
7. Remove the door glass upward.
8. Remove the mounting bolts, and remove the regu-
lator through the service hole.
9. Remove the window motor mounting bolt, and re-
move the motor from the regulator (power window).
Removal of Outer Handle and Key Cylinder
1. Disconnect the rod from the outer handle.
69G14X-036
14—16

1 4 REAR DOORS
86U14X-047
86U14X-048
86U14X-049
REMOVAL
Rear Door Glass and Regulator
1. Lower the door glass the way.
2. Remove the clip. (Manual type)
3. Remove the regulator handle. (Manual type)
4. Remove the inner handle cover.
5. Remove the door trim.
Note
For vehicles with power windows, disconnect
the connectors.
6. Remove the door screen.
Caution
Remove the screen carefully so that it may be
reused.
7. Position the door glass so that the mounting bolts
can be removed from the service hole.
8. Remove the mounting bolts.
86U14X-050
14—20