1987 MAZDA 626 clutch

7C ASSEMBLY
7C-112
Procedure
1. Use the following procedure to adjust the total end
play and select a suitable bearing race.
(1) Remove the pump cover from the oil pump.
(2) Install the bearing into the rear clutch drum.
(3) Mount the bearing race to the pump cover; and
then install it into the front clutch drum.
Note
A front clutch drum end play adjust shim must
not be used between the pump cover and the
front clutch drum when checking total end
play.
(4) Position a straight edge on the transaxle case,
and measure the clearance between the
straight edge and either the pump cover or the
transaxle case.
a) If the pump cover surface is lower than the
transaxle case, measure the clearance be-
tween the straight edge and the pump
cover.
Specification:
0.10 mm (0.004 in) max.
Note
a) Make the measurement without the oil
pump gasket installed.
b) Measured clearance plus thickness of oil
pump gasket equals total end play.
b) If the pump cover surface is higher than the
transaxle case, measure the clearance be-
tween the straight edge and the transaxle
case.
Specification:
0.15 mm (0.006 in) max.
Caution
Do not position the straight edge on the bolt
holes for mounting the oil pump to the trans-
axle case.
Note
Thickness of oil pump gasket minus measured
clearance equals total end play.
2. If the end play is not within specification, adjust it
by selecting the proper bearing race.
Caution
Use only one bearing race.
Bearing race outer diameter: 41.0 mm (1.61 in)
Bearing race sizes mm (in)

1.2 (0.047) 1.4 CO.055) 1.6 (0.063)
1.8 (0.071) 2.0 (0.079) 2.2 (0.087)

3. Reinstall the oil pump cover.
Tightening torque: 11—14 N-m
(110—140 cm-kg, 95—122 in-lb)

ASSEMBLY 7C
4. Use the following procedure to adjust the front
clutch drum end play and select the adjust shim.
(1) Set the oil pump gasket onto the transaxle
case.
(2) Place the adjust shim onto the front clutch
drum.
(3) Install the oil pump and bearing race into the
transaxle; then tighten the oil pump mounting
bolts to the specified torque.
Tightening torque:
15—22 N m (1.5—2.2 m-kg, 11—16 ft-lb)
76G07C-300
76G07C-301
63U07B-220
(4) Position the transaxle with the oil pump facing
down ward position.
(5) While turning the connecting shell 2 complete
turns, push the front clutch drum toward the
oil pump with a screwdriver to seat the front
clutch drum.
(6) Measure the clearance between the front clutch
drum and the connecting shell. This clearance
is the front clutch drum end play.
End play: 0.5—0.8 mm (0.020—0.031 in)
(7) If the end play is not within specification, ad-
just it by selecting the proper adjust shim.
Shim sizes mm (in)

1.3 (0.051) 1.5 (0.059) 1.7 (0.067)
2.3 (0.091) 1.9 (0.075) 2.1 (0.083)
1.7 (0.067)
2.3 (0.091)
2.5 (0.098) 2.7 (0.106)

76G07C-302
7C-113

HYDRAULIC CIRCUIT 7C
R RANGE
Band servo
Release side
Oil cooler
Low and reverse brake 1 pressure Vacuum diaphragm Kick-down solenoid Rear clutch pressure
Front clutch pressure
Downshift valve H Oil pump Vacuum throttle valve
Throttle backup valve
Orifice check valve
Modifier 15| valve
2-3 shift valve
Second lock valve
Orifice valve Pressure regulator valve
Line pressure t4s2
Operating line pressure
Governor pressure
Torque converter
Throttle pressure Secondary x governor valve Primary governor valve
76G07C-340
7C—127

7C HYDRAULIC CIRCUIT
N RANGE
Oil cooler
Low and reverse brake •l pressure Vacuum diaphragm Kick-down solenoid
Rear clutch pressure
Front clutch pressure
Downshift valve 11 Oil pump Throttle backup valve
Vacuum throttle valve
x 18 Orifice YjI check valve H [ Throttle relief I valve
Modifier 15| valve Orifice check
I
valve
Orifice check valve 11 j! Pressure regulator valve
Line pressure
Governor pressure
Torque converter
Throttle pressure Primary governor valve Secondary x governor valve
76G07C-341
7C—128

HYDRAULIC CIRCUIT 7C
D RANGE (1ST GEAR)
Band servo
Kick-down solenoid
Downshift valve Throttle backup valve
76G07C-342
Pressure regulator valve
Line pressure
Operating line pressure
Governor pressure
Torque converter
Throttle pressure
Orifice ch< valve
Secondary * Primary x governor valve governor valve
Vacuum | throttle valve
valve
Apply side
Release side
Low and reverse brake pressure
Rear clutch pressure
Vacuum diaphragm
Oil pump
Throttle relief valve
J Orifii check valve
Orifice check valve
Front clutch pressure
Modifier 1! valve
7C—129

7C HYDRAULIC CIRCUIT
D RANGE (2ND GEAR)
Band servo
Vacuum diaphragm
Throttle backup valve
Orifice valve
76G07C-343
Oil cooler
Apply side
Release side
Oil pump
Secondary * governor valve Primary governor valve
Pressure regulator valve
Line pressure
Operating line pressure
Governor pressure
Torque converter
Throttle pressure
Orifice check valve
Modifier < valve
Low and reverse brake pressure
Rear clutch pressure
Front clutch pressure
Vacuum | throttle valve
Orifice check valve
Downshift valve 11
Throttl relief valve
Kick-down solenoid
7C—130

HYDRAULIC CIRCUIT 7C
D RANGE (3RD GEAR)
Band servo
Oil cooler
Low and reverse brake • pressure
Rear clutch pressure
4 Front clutch pressure
Vacuum diaphragm Kick-down solenoid
Downshift valve i I Vacuum throttle valve
Throttle backup valve
Orifice check valve
Modifier valve
Orifice check valve 11 Pressure regulator valve
Line pressure lis
Operating line pressure
Governor pressure
Torque converter
Throttle pressure Secondary x governor valve Primary * governor valve
76G07C-344
7C—131

7C HYDRAULIC CIRCUIT
D RANGE (KICK-DOWN; SHIFT VALVES IN 2ND POSITION)
Band servo
Oil cooler
Low and reverse brake • pressure Kick-down solenoid Vacuum 'diaphragm
Rear clutch pressure
Front clutch pressure
Jownshift 'alve 11 Oil pump Vacuum throttle valve
Throttle backup valve
Throttle relief I valve
Orifice check valve
Modifier valve Orifiw check valve
Second lock valve
Orifice chabk valve II Pressure regulator valve
CZ3 Line pressure
Ml Operating line pressure
• Governor pressure
Cm Torque converter
•I Throttle pressure
Primary x governor valve Secondary x governor valve
76G07C-345
7C—132