1986 TOYOTA LAND CRUISER roof

BO1K4-05
H05401
No. 2 Roof Drip Side Finish Center Moulding
Roof Drip Side Finish Moulding
No. 2 Roof Drip Side
Finish Moulding Clip



Non-reusable part BO-48
- BODYROOF DRIP SIDE FINISH MOULDING
2622 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ROOF DRIP SIDE FINISH MOULDING
COMPONENTS

BO1K6-05
BO-50
- BODYROOF DRIP SIDE FINISH MOULDING
2624 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. INSTALL NO. 2 ROOF DRIP SIDE FINISH MOULDING CLIP
If the No. 2 roof drip side finish moulding clip comes off.
(a) Using a heat light, heat the body mounting surface to 40 - 60 °C (104 - 140 °F).
NOTICE:
Do not heat the body excessively.
(b) Remove the adhesive tape and adhesive from the body.
(c) Wipe off stains with cleaner.
(d) Using a heat light, heat the body and clip.
Body: 40 - 60 °C (104 - 140 °F)
Clip: 20 - 30 °C (68 - 86 °F)
NOTICE:
Do not heat the body and clip excessively.
(e) Install the clip.
2. INSTALL NO. 2 ROOF DRIP SIDE FINISH CENTER MOULDING
Install the No. 2 roof drip side finish center moulding to the roof drip side finish moulding.
3. INSTALL ROOF DRIP SIDE FINISH MOULDING

BO1K5-03
H05400
Roof Drip Side Finish Moulding
Moulding Remover
No. 2 Roof Drip Side
Finish Moulding Clip
- BODYROOF DRIP SIDE FINISH MOULDING
BO-49
2623 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE NO. 2 ROOF DRIP SIDE FINISH CENTER
MOULDINGS
2. REMOVE ROOF DRIP SIDE FINISH MOULDING
Using a moulding remover, remove the roof drip side finish
moulding.
NOTICE:

Do not damage the body.

Do not remove the No. 2 roof drip side finish moulding
clip.

When the clip comes off, replace it with a new one.
HINT:
Tape the moulding remover tip before use.

BO1KP-04
H18921
Dome Light
Lens
Roof Headlining
Rear Trim
Roof Headlining Double Visor
Map Lamp
Center Pillar Garnish
Rear Mat
Set Plate
Striker Plate
Upper Roof
Side Inner Garnish Assist Grip
Cowl Side Trim Front Door Scuff Plate
Center Pillar Lower
Garnish CoverRear Door
Scuff PlateQuarter Trim PanelQuarter Trim
Jack Cover
Front Pillar Garnish Front Door
Opening TrimRear Door
Opening Trim Sun Visor
Holder
Assist Grip
Plug
Overhead
Console Box
Striker Plate
Center Pillar
Lower Garnish
Front Assist Grip
Front Assist Grip
Center Assist Gripw/ Curtain Shield Airbag:
42 (430, 31)
Adjustable
AnchorRear A/C Register
Rear A/C Register
Rear A/C Control Panel Rear A/C Register
Striker Plate
Striker Plate
Center Assist Grip
Center Assist Grip
Assist Grip
Rear
Assist Grip
x5Striker Plate
Center Assist Grip w/ Curtain Shield Airbag:
Adjustable
Anchor
Center Pillar Garnish
Center
Pillar
Garnish
: Specified torqueN´m (kgf´cm, ft´lbf)Rear Mat42 (430, 31)
Cap
Cap
Holder
rear
Assist Grip
w/ Curtain Shield Airbag:
Assist Grip
Assist Grip
Assist Grip Plug
w/ Curtain Shield Airbag:
Assist
Grip
Assist Grip Plug
Assist Grip
42 (430, 31)
Lens
Room Temperature
Sensor
BO-96
- BODYROOF HEADLINING
2670 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ROOF HEADLINING
COMPONENTS

BO1KR-01
- BODYROOF HEADLINING
BO-101
2675 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page BO-97).

BO4IZ-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips
- BODYROOF HEADLINING
BO-97
2671 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATES
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATES
9. REMOVE REAR DOOR OPENING TRIMS
10. REMOVE QUARTER TRIM PANEL LH
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel LH, then disconnect the
connector.

H18922
10 Clips
H18906
: 9 Clips
H18904
H05264
Claw
BO-98
- BODYROOF HEADLINING
2672 Author
: Date
:
2004 LAND CRUISER (RM1071U)
11. REMOVE QUARTER TRIM PANEL RH
(a) Using a clip remover, remove the clip.
(b) Remove the quarter trim panel RH.
12. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHORS
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
13. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHORS
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
14. REMOVE UPPER ROOF SIDE INNER GARNISHES
(a) Using a screwdriver, remove the 2 assist grip plugs, then
remove the 2 screws and the assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, remove the upper roof side inner gar-
nish.
HINT:
Tape up the screwdriver tip before use.
(d) Use the same manner described above to the other side.
15. REMOVE FRONT DOOR SCUFF PLATES
16. REMOVE COWL SIDE TRIMS
17. REMOVE FRONT DOOR OPENING TRIMS
18. REMOVE FRONT ASSIST GRIP
(a) Using a screwdriver, remove the 2 assist grip plugs, then
remove the 2 screws and front assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Use the same manner described above to the other side.
19. REMOVE FRONT PILLAR GARNISH
(a) Using a screwdriver, remove the front pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(b) Use the same manner described above to the other side.
20. REMOVE CENTER PILLAR LOWER GARNISH
(a) Using a screwdriver, remove the center pillar garnish cov-
er.
HINT:
Tape up the screwdriver tip before use.

H05265
: 4 Clips
H21424
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
H21425
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
- BODYROOF HEADLINING
BO-99
2673 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Using a screwdriver, remove the center pillar lower gar-
nish as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
(c) Use the same manner described above to the other side.
21. REMOVE CENTER PILLAR GARNISH
(a) Using a screwdriver, remove the seat belt anchor cover
cap.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the bolt and the front seat outer belt shoulder an-
chor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(c) Using a clip remover, remove the clip.
(d) Using a screwdriver, remove the center pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(e) Use the same manner described above to the other side.
22. REMOVE SUN VISOR
(a) Using a screwdriver, remove the caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screws, then disconnect the connectors.
(c) Remove the sun visors.
23. REMOVE DOUBLE VISOR
Remove the screws and the double visors.
24. REMOVE HOLDER
Remove the screws and the holders.