1986 TOYOTA LAND CRUISER roof

Tool
Ta b
Ta b
Terminal
Retainer
Access Hole
( Mark)Tool
Tool
[Female] Example:
[Male] (Case 1)
[Male] [Female]Retainer
at Full Lock Position
Retainer
at Temporary Lock Position
Terminal Retainer
[Male]Press Down
[Female]Press DownTool
Tool Example:
(Case 2)
2004 LAND CRUISER (EWD548U)
15 C
[B] For Waterproof Type Connector
HINT : Ter m inal ret ainer color is diff er ent
according to connector body.
Example:
Terminal Retainer
: Connector Body
Black or White : Gray
Black or White : Dark Gray
Gray or White : Black
ºCase 1º
Type where terminal retainer is pulled
up to the temporary lock position (Pull
Type).
Insert the special tool into the terminal
retainer access hole (
Mark) and pull
the terminal retainer up to the
temporary lock position.
HINT : The needle insertion position varies
according to the connector 's shape
(Number of terminals etc.), so check
the position before inserting it.
ºCase 2º
Type which cannot be pulled as far as
Power Lock insert the tool straight into
the access hole of terminal retainer as
shown.

- SERVICE SPECIFICATIONSBODY ELECTRICAL
SS-47
187 Author
: Date
:
2004 LAND CRUISER (RM1071U) B22 - Ground (Ignition switch ON)
Battery positive voltage
A10 - Ground (Constant)Battery positive voltage
DEFOGGER SWITCH (w/o Navigation)
8 - Ground (Ignition switch LOCK or ACC)No voltage
8 - Ground (Ignition switch ON)Battery positive voltage
2 - Ground (Constant)Battery positive voltage
SLIDING ROOF CONTROL ASSEMBLY
5 - Ground (Constant)Battery positive voltage
8 - Ground (Ignition switch LOCK or ACC)No voltage
8 - Ground (Ignition switch ON)Battery positive voltage
POWER MIRROR SWITCH
4 - Ground (Ignition switch LOCK)No voltage
4 - Ground (Ignition switch ACC or ON)Battery positive voltage
POWER SEAT SWITCH (Driver's Seat)
11 - Ground (Constant)Battery positive voltage
POWER SEAT SWITCH (Passenger's Seat)
11 - Ground (Constant)Battery positive voltage
LUMBAR SUPPORT SWITCH (Driver's Seat)
POWER MIRROR SWITCH (Wire harness side)
4 - Ground (Ignition switch is LOCK)No voltage
4 - Ground (Ignition switch is ACC or ON)Battery positive voltage
POWER AMPLIFIER
7 - Ground (Constant)Battery positive voltage
16 - Ground (Constant)Battery positive voltage
REAR SEAT AUDIO
24 - Ground (Ignition switch LOCK)No voltage
24 - Ground (Ignition switch ACC or ON)Battery positive voltage
12 - Ground (Constant)Battery positive voltage
DVD CHANGER
1 - Ground (Ignition switch LOCK)No voltage
1 - Ground (Ignition switch ACC or ON)Battery positive voltage
10 - Ground (Constant)Battery positive voltage
RADIO RECEIVER
A1 - Ground (Ignition switch LOCK)No voltage
A11 - Ground (Ignition switch ACC or ON)Battery positive voltage
A11 - Ground (Constant)Battery positive voltage
ANTENNA MOTOR CONTROL RELAY
4 - Ground (Constant)Battery positive voltage
7 - Ground (Ignition switch ACC or LOCK)No voltage
7 - Ground (Ignition switch ON)Battery positive voltage
17 - Ground (Ignition switch LOCK)No voltage
17 - Ground (Ignition switch ACC or ON)Battery positive voltage
OVERHEAD J/B
8 - Ground (Constant)Battery positive voltage

RS0N4-09
H20931
H20932
RS-60
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2335 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. Vehicle not involved in collision:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the curtain shield airbag assembly installed in the vehicle.
Check cuts, minute cracks or marked discoloration on the
front pillar garnish and roof headlining.
2. Vehicle involved in a collision and airbag is not
deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the curtain shield airbag assembly removed from the ve-
hicle.

Check cuts, tears and cracks, or marked discolor-
ation of the curtain shield airbag assembly.

Check cuts and cracks in wire harness, and chip-
ping in connectors.
CAUTION:
For removal and installation of the curtain shield airbag as-
sembly, see page RS-59 and RS-68. Be sure to follow the
correct procedure.
3. Vehicle involved in a collision and airbag is deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the curtain shield airbag assembly removed from the ve-
hicle.

Check the deformation or cracks on the body that
the curtain shield airbag installed on.

Check the damage to the connector and wire har-
ness.
HINT:
If the body that the curtain shield airbag was installed on is de-
formed or cracked, replace it.

RS0TH-03
H20929
(1)(3)
(2)(3)
(3) RS-68
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2343 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a) In the order shown in the illustration, install the curtain
shield airbag with the 8 bolts.
Torque: 9.8 N´m (100 kgf´cm, 86 in.´lbf)
CAUTION:
Pay due attention not to twist the deployment section of the
curtain shield airbag assembly.
NOTICE:

Make sure that the curtain shield airbag assembly is
installed to the specified torque.

If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.

When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.
(b) Connect the connector of the curtain shield airbag as-
sembly.
2. INSTALL ROOF HEADLINING (See page BO-101)
3. INSPECT SRS WARNING LIGHT (See page DI-692)

RS0TG-03
H20929
(1)
(1)(3)
(2)
(1)
H20930
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS-59
2334 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:

If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.

Never use the airbag parts from another vehicle.
When replacing parts, replace them with new parts.
1. REMOVE ROOF HEADLINING (See page BO-97)
2. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(b) In the order shown in the illustration, remove the bolts and
curtain shield airbag assembly.
HINT:

Loosen the bolt (3) before removing the bolt (2).

Bind the front and rear parts of the curtain shield airbag
assembly before removing the bolt (3).
(c) Put the removed curtain shield airbag in a clear plastic
bag and keep it in a safe place.
CAUTION:
Never disassemble the curtain shield airbag assembly.
NOTICE:
Plastic bag is not reusable.

RS0N6-06
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS-67
2342 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the curtain shield airbag assembly or curtain shield airbag cover.
CaseReplacing part
If the curtain shield airbag has been deployed.Curtain shield airbag assembly
If the curtain shield airbag assembly has been found to be faulty in trouble-
shooting.Curtain shield airbag assembly
If the curtain shield airbag assembly has been found to be faulty during
checking items (See page RS-60).Curtain shield airbag assembly
If the front pillar garnish has been found to be faulty during checking items
(See page RS-60).Front pillar garnish
If the roof headlining has been found to be faulty during checking items
(See page RS-60).Roof headlining
If the curtain shield airbag assembly has been dropped.Curtain shield airbag assembly
CAUTION:
For removal and installation of the curtain shield airbag assembly, see page RS-59 and RS-68. Be
sure to follow the correct procedure.