1986 TOYOTA LAND CRUISER roof

I24922
Cowl Side J/B LH
ABCD
Relays:
A. DEFOG
B. IG1 No.2
C. ACC
D. DOME Fuses:
1. AHC-IG
2. POWER HTR
3. FUEL HTR
4. AHC-B
5. DEFOG
6. AM1
7. ACC
8. CIG
9. PWR OUTLET
10. OBD-2
11. STOP
12. A/C
13. BATT CHARGE
14. DBL LOCK
15. ECU-B1
16. ECU-IG1
17. GAUGE1
18. EFI or ECD NO.2
19. RR WIPER
20. SUN ROOF
21. DOOR
22. LH SEAT
23. IDLE UP
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
19 20 21 22 23
- BODY ELECTRICALPOWER SOURCE
BE-13
2386 Author
: Date
:
2004 LAND CRUISER (RM1071U)

BE0S9-04
I06151
I04045
Wire Harness Side:
- BODY ELECTRICALSLIDING ROOF SYSTEM
BE-107
2480 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT SLIDING ROOF SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
SLIDE OPEN3 - 5Continuity
SLIDE OFF -No continuity
SLIDE CLOSE3 - 4Continuity
TILT DOWN2 - 3Continuity
TILT OFF -No continuity
TILT UP1 - 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SLIDING ROOF CONTROL ASSEMBLY CIR-
CUIT
Disconnect the connector from the ECU and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 - GroundConstantContinuity
4 - GroundSliding roof control switch (TILT) OFF or CLOSENo continuity
4 - GroundSliding roof control switch (TILT) UPContinuity
5 - GroundConstantBattery positive voltage
3 - GroundConstantContinuity
3 - GroundSliding roof control switch (TILT) OFF or UPNo continuity
7 - GroundSliding roof control switch (TILT) DOWNContinuity
8 - GroundIgnition switch LOCK or ACC* No voltage
8 - GroundIgnition switch ONBattery positive voltage
9 - GroundSliding roof control switch (SLIDE) OFF or
CLOSENo continuity
9 - GroundSliding roof control switch (SLIDE) OPENContinuity
10 - GroundSliding roof control switch (SLIDE) OFF or OPENNo continuity
10 - GroundSliding roof control switch (SLIDE) CLOSEContinuity
*: Exceptions: During 45 second period after ignition switch
ON"OFF (ACC) or until driver or passenger door is opened af-
ter ignition switch ON"OFF (ACC).

BE-108
- BODY ELECTRICALSLIDING ROOF SYSTEM
2481 Author
: Date
:
2004 LAND CRUISER (RM1071U)
If circuit is as specified, replace the relay.

BE0S8-05
I24749
Sliding Roof Control Gear Assembly with ECU
Cowl SId e J/B LH

SUN ROOF Fuse

ECU-IG1 Fuse
Ignition SwitchSliding Roof Control Switch
BE-106
- BODY ELECTRICALSLIDING ROOF SYSTEM
2479 Author
: Date
:
2004 LAND CRUISER (RM1071U)
LOCATION

BE0O9-02
Sliding Roof reverses during close (down) operation.
Start
Mechanical check
Replace sliding roof motor with ECU. Perform forced operation.*
*: Holding the CLOSE/UP (OPEN/DOWN) switch pressed inhibits the jam protection function at approx.
10 sec. after starting the reverse operation.
If the switch remains pressed any longer, the sliding door starts close operation and it stops when
detecting the fully closed position.
CLOSE/UP
(OPEN/DOWN)
SWITCHON
OFF
Close
(Down)
Roof OperationStop Forced Operation Reverse
Stop
Close (Down)
Close Position Approx. 10 sec.
HINT:
At approx. 10 sec. after starting the reverse operation, it is switched to the forced close (down) operation.
- BODY ELECTRICALSLIDING ROOF SYSTEM
BE-105
2478 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SLIDING ROOF SYSTEM
TROUBLESHOOTING

BO1LD-03
H18905
Rear Door Opening TrimRoof Headlining Rear Trim
Upper Roof Side
Inner Garnish
Quarter Trim Jack CoverStriker Plate
Quarter Trim Panel Rear Door Scuff PlateQuarter Belt MouldingRear Mat
Rear Mat Set Plate Quarter Window
GlassStriker Plate Quarter Window
Glass Weatherstrip
Striker Plate
x5 Rear
Assist Grip Rear Vent Window Motor
Assist Grip
Plug
Assist Grip
Plug
- BODYQUARTER WINDOW GLASS
BO-61
2635 Author
: Date
:
2004 LAND CRUISER (RM1071U)
QUARTER WINDOW GLASS
COMPONENTS

BO4IW-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips BO-62
- BODYQUARTER WINDOW GLASS
2636 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATE
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque:42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATE
9. REMOVE REAR DOOR OPENING TRIM
10. REMOVE QUARTER TRIM PANEL
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel, then disconnect the con-
nector.
11. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHOR
12. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHOR

H18906
: 9 Clips
H04108
H05403
Quarter Belt
Moulding
Clip
: 4 Clips
H04110
- BODYQUARTER WINDOW GLASS
BO-63
2637 Author
: Date
:
2004 LAND CRUISER (RM1071U)
13. REMOVE UPPER ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the assist grip plugs, then re-
move the 2 screws and the rear assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, remove the upper roof side inner gar-
nish.
HINT:
Tape the screwdriver tip before use.
14. REMOVE QUARTER WINDOW GLASS
(a) Disconnect the connector.
(b) w/ Antenna:
Disconnect the connector.
(c) Remove the 2 bolts, the 2 nuts and the quarter window
glass.
15. REMOVE QUARTER WINDOW GLASS WEATH-
ERSTRIP
16. REMOVE QUARTER BELT MOULDING
(a) Remove the screw.
(b) Using a screwdriver, remove the quarter belt moulding.
HINT:
Tape up the screwdriver tip before use.
17. REMOVE REAR VENT WINDOW MOTOR
Remove the screw and the rear vent window motor.
18. REMOVE QUARTER WINDOW LOCK
Remove the screw and the quarter window lock.