1986 TOYOTA CAMRY V20 service

Maintenance services indicated by a star (*) or asterisk (*) are required under the terms of the Emission Control Systems Warranty.
See Owner's Guide or Warranty
Booklet for complete warranty information.

For vehicles sold in California
* For vehicles sold outside California
(1) Includes inspection of fuel tank band and vapor vent system.
(2) Also applicable to drum lining for parking brake.
(3) Check for leakage.
(4) Check for oil leaks from steering gear housing.
(5) The applicable part are listed below
wFront and rear suspension member to body
wStrut bar bracket to body bolts
wBolts for sheet installation
Maintenance service beyond 60,000 miles (96,000 km) should continue to be performed at the same intervals shown
for each maintenance schedule.
SCHEDULE BCONDITIONS: Conditions other than those listed for SCHEDULE A.
Service interval
(Odometer reading or
months, whichever
comes first)
Maintenance items
Manual transaxle, automatic
transaxle and differential (3) Brake pads and discs (Front and rearBolts and nuts on chassis and body 17)Exhaust pipes and mountings
Steering gear housing oil 1s) Brake linings and drums (4)
Brake line pipes and hoses Fuel lines and connections (31
Ball joints and dust covers Engine oil and oil filterSpark plugs (platinum tippedFuel tank cap gasket
MA±14 (item 22) MA±10 (item 20)
Charcoal canister
Steering linkage
Drive shaft boots
MA±7 (item 11)
MA±9 (item 19) MA±9 (item 18) MA±7 (item 13) MA±7 (item 10)
MA±8 (item 14) MA±7 (item 12)
MA±8 (item 16) MA±8 (item 15) See page
(item No.)
Engine coolant
MA±9 (item 17)
Valve clearance
MA±6 (item 8) MA±4 (item 2)
MA±6 (item 9) MA±6 (item 7)
MA±6 (item 7)
MA±5 (item 5) MA±5 (item 4)
Drive belts
Air filterSpark plugs
IGNITION
CHASSISBRAKES ENGINESystem
EVAPFUEL
± MAINTENANCEMaintenance ScheduleMA±3

GENERAL MAINTENANCE
These are the maintenance and inspection items
which are considered to be the owner's responsibility,
They can be performed by the owner or he
can have then done at a service shop. These items
include those which should be checked on a daily ba-
sis, those which, in most cases, do not require
(special) tools and those which are considered to be
reasonable for the owner to perform.
Items and procedures for general maintenance are as
follows:
OUTSIDE VEHICLE
1. TIRES
(a) Check the pressure with a gauge. Adjust
if necessary.
(b) Check for cuts, damage or excessive wear.
2. WHEEL NUTS
When checking the tires, check the nuts for looseness
or for missing nuts. If necessary,
tighten them.
3. TIRE ROTATION
It is recommended that tires be rotated every
7,500 miles (12,000 km).
4. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe
clean. Replace if necessary.
5. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or
other fluid.
(b) If you smell gasoline fumes or notice any leak,
have the cause found and corrected.
6. DOORS AND ENGINE HOOD
(a) Check that all doors including the trunk lid and
back door operate smoothly, and that all
latches lock securely.
(b) Check that the engine hood secondary latch se-
cures the hood from opening when the prima-
ry latch is released.
INSIDE VEHICLE
7. LIGHTS
(a) Check that the headlights, stop lights, taillights,
turn signal lights, and other
lights are all working.
(b) Check the headlight aiming.8. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers func-
tion properly.
9. HORN
Check that it is working.
10. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
11. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
12. WINDSHIELD DEFROSTER
Check that air comes out from the defroster out-
let when operating the heater or air conditioner
at defroster mode.
13. REAR VIEW MIRROR
Check that it is mounted securely.
14. SUN VISORS
Check that they move freely and are mounted
securely.
15. STEERING WHEEL
Check that it has the specified freeplay. Be alert
for changes in steering condition, such as hard
steering, excessive freeplay or strange noise.
16. SEATS
(a) Check that all front seat controls such as
seat adjusters, seatback recliner, etc.
operate smoothly.
(b) Check that a11 latches lock securely in
any position.
(c) Check that the locks hold securely in any
latched position.
(d) Check that the head restraints move up
and down smoothly and that the locks
hold securely in any latched position.
(e) For folding±down rear seat backs, check
that the latches lock securely.
17. SEAT BELTS
(a) Check that the seat belt system such as
buckles, retractors and anchors operate
properly and smoothly.
(b) Check that the belt webbing is not cut,
frayed, worn or damaged.
± MAINTENANCEGeneral MaintenanceMA±16

SERVICE SPECIFICATIONS
± SERVICE SPECIFICATIONSA±1

Front and rear brake
Pad thickness
Disc thickness
Disc runout
Parking brake
Lining thickness
Drum inside diameter
Front axle and suspension
Ball joint vertical play
Steering wheel freeplay
Torque specifications
Front seat mount bolts
Strut/stabilizer bar bracket x Body
Engine mounting center member x Body
Front suspension lower crossmember x Body
Rear suspension lower crossmember x Body
MAINTENANCE
Engine
Engine oil capacity (Drain and refill with oil fitter change)
Gap
Firing order
Valve clearance Coolant capacity 1w/ Heater) Drive belt tension
Alternator
Spark plug
Type
Chassis
PS pump
± SERVICE SPECIFICATIONSMaintenanceA±2

ENGINE MECHANICAL (3S±FE)
Specifications
Intake manifold
vacuum
Camshaft and
gearCompression
pressure
Valve guide
bushingCylinder head
Valve spring
Valve lifterIdle speed
ManifoldValve
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±3

Specifications (Cont'd)
Idler pulley
tension springCamshaft and
gear (cont'd)
Piston and
piston ring
Connecting rod Cylinder block
Crankshaft
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±4

Spark plug tube x Cylinder head
Camshaft bearing cap x Cylinder head
Cylinder head cover x Cylinder head
Intake manifold x Cylinder head
Intake manifold stay x Cylinder head
Intake manifold stay x Cylinder block
EGR valve x Intake manifold
EGR pipe x Cylinder head
Water outlet x Cylinder head
Exhaust manifold x Catalytic converter
Exhaust manifold x Cylinder head
Engine hanger x Cylinder head
Alternator bracket x Cylinder headOil pump pulley x Oil pump drive shaft
No. 1 idler pulley x Cylinder head
No. 2 idler pulley x Cylinder block
Camshaft timing pulley x Camshaft
Crankshaft pulley x Crankshaft
Cylinder head x Cylinder block
Specifications (Cont'd)
Torque Specifications
Crankshaft
(cont'd)
Part tightened
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±5

Engine RH mounting bracket x Cylinder block
Engine RH mounting insulator x Engine mounting bracket
Engine RH mounting insulator x Body (2WD)
Engine RH mounting insulator x Body (4WD)
Engine RH mounting stay x Engine mounting insulator
Engine RH mounting stay x Alternator bracket
Engine LH mounting bracket x Transaxle
Engine LH mounting insulator x Engine mounting insulator
Engine LH mounting insulator x Body
Engine LH mounting stay x Engine mounting insulator (4/T)
Engine LH mounting stay x Transaxle (A/T)
Engine front mounting bracket x Transaxle
Engine front mounting insulator x Engine mounting bracket
Engine center mounting bracket x Cylinder block (2WD)
Engine rear mounting x Transaxle
Engine rear mounting insulator x Engine mounting bracket
Engine front pipe x Catalytic converter
Exhaust front pipe x Exhaust center pipeMain bearing cap X Cylinder block
Connecting rod cap x Connecting rod
Rear oil seal retainer x Cylinder block
Rear end plate X Cylinder block
Flywheel x Crankshaft (M/T)
Drive plate x Crankshaft (A/T)
Suspension lower crossmember x Body
Suspension lower crossmember x Engine mounting center member
Engine mounting center member x Body
Engine mounting center member x Engine mounting insulator
Torque Specifications (Cont'd)
Part tightened
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±6