1973 OPEL GT-R Service Manual

ZE-221973 OPEL SERVICE MANUAL’REAR COMPARTMENT LID
CONTENTS
Subject
DESCRIPTION AND OPERATION: (Not Applicable)
DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS: (Not
Applicable)
MAJOR REPAIR:
Removal and Installation
Weatherstrip
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Lock Cylinder
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LuggageCompartmentLid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SPECIFICATIONS: (Not Applicable)Page No.
2E-22
2E-22
2E-23
MAJOR REPAIRREMOVAL AND INSTALLATION OF LUGGAGE
COMPARTMENT LID WEATHERSTRIP
1. Detach old weatherstrip and clean sealing surface.2. Coat new weatherstrip and contacting surface
with rubber cement, and allow cement to dry for a
few minutes.3. Install new weatherstrip with rubber cement. See
Figure
2E-2.REMOVAL AND INSTALLATION OF LUGGAGE
COMPARTMENT LID LOCK CYLINDER
Removal
1. Remove luggage compartment lid lock. See Figure
2E-3.Figure
ZE-2 installing Luggage Compartment Lid2. With luggage compartment lid in almost horizon-Weatherstriptal position, unscrew lock cylinder nut, using a 13/16Figure
2E-3 Lid Lock Attaching Screws

REAR COMPARTMENT LID2E- 23
inch deep socket, and remove it, together with inter-
mediate ring. See Figure 2E-4.Fiyure
ZE-4 Removing Lock Cylinder Nut
Installation
1. Install lock cylinder nut, together with intermedi-
ate ring, and fasten with a 13/16 inch deep socket.
See Figure 2B96.
2. Install luggage compartment lock so that the lock
cylinder rod rests in opening of the lock. See Figure
2E-5.REMOVAL AND INSTALLATION OF LUGGAGE
COMPARTMENT LID
Removal1. With a wooden wedge, remove letters and orna-
ment.
2. From below, push ornament out of luggage com-
partment lid.2E-5
Figure
ZE-5 Lock Cylinder Rod Location
3. Remove rubber bumpers, lamp, lid lock, and lock
cylinder. See Figure
2E-6.Figure
2E-6 Rubber Bumpers Lamp and Lock Location
4. Unscrew luggage compartment lid from hinges.
5. The luggage compartment lid must be aligned so
that the gaps between lid and adjacent surfaces are
almost equal.

2F-241973 OPEL SERVICE MANUAL
ROOF AND SUN ROOF
CONTENTS
,.,Subject
DESC,RIF?TION AND OPERATION: (Not Applicable)
DIAGNOSIS: Sun Roof Diagnosis
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE AND ADJUSTMENTS:Sun Roof Height Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . .
MAJOR REPAIR:
Removal and Installation
Sun Roof Panel andFrame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . .
Velvet Strip and Weather Strip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RearGuides andCables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . .
Drive Pinion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water DrainHoses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . .
Luggage Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS: (Not Applicable) Page No.
2F-24
2F-26
iF-27
2F-29
2F-29
2F-30
2F-31
2F-3i
DIAGNOSIS
SUN ROOF DIAGNOSIS
_ -
CONhTlONPAUSEI~C~RRECTI~X~
Sun roof does not operate
Transporter cable lengths
parallel. equal.Close sun roof, slide sun roof
frame to rear, remove.crank
handle
and cable crank. Check
that sun roof bears against sun
roof opening velvet strip and
that lifter’ portion of rear lifter
guides is positioned approximately
90 degrees to guide rails.
Turn
cable crank fully clockwise and
reinstall into cable box.
Transporter cables damaged
or worn. Replace cables. Both cables
must be replaced if either one
is damaged or worn.

ROOF AND SUN ROOFZF-25ConditionCallseCorrectionSun roof lifts up on one
side only.Lifter wedge welded to under-
Remove sun roof panel and bend
side of sun roof panel doeslifter wedge so that it squarely hits
not run up ramp welded inramp. The only adjustment for
center of sun roof track.the ramp is the angle of the
rear portion. This should be
adjusted so that the wedge smoothly
rides up the ramp.
Transporter cable or drive
pinion damaged.If the transporter cable is worn
or damaged, replace both
cables. If drive pinion worn or
damaged, replace drive pinion and
also both transporter cables.
Sun roof scrapes on car roof
when closing sun roof.Lifters do not lie flat.Close sun roof, slide sun roof
frame to the rear and open and close
sun roof slightly noting operation
of lifters. Rework if necessary,plastjc lifter cushion with tile
to permit lifter to lie flat.
Sparingly lubricate lifter guide.
Sun roof frame becomes
detached.Attaching clips have lost
elasticity.Install new clips
Water enters car interior.
Water drain hoses blocked.
Bent water drain hoses
Rear water drain hoses have
been pulled out of rubber
grommets.
Velvet strips on front and
rear of sun roof do not seal
properly.Clean hoses with compressed air
or a flexible steel cable.
NOTE: To clear rear water
drain hoses, the sun roof panel
and frame must be removed.
Blowing out of rear drain hoses
from trunk compartment hose end
is not recommended due to
possibility of soiling car
interior.
Attempt to straighten drain
hoses by working a suitable
tube or cable through hose.
Replace hose if above corrective
action is not satisfactory.
Apply a small amount of rubber
cement to rear water drain
hoses and reinsert into rubber
grommet located in luggage
compartment floor panel.
Check sun roof for correct
height adjustment. If height
adjustment is correct, but a
tight seal does not exist,
relocate velvet strip upward
for better seal, or replace
velvet strip.

2F-261973 OPEL SERVICE MANUALMAINTENANCE AND ADJUSTMENTSADJUSTING HEIGHT OF SUN ROOF PANEL
Adjust height of sun roof as follows:
1. Opel sun roof to half open position and pry apart
sun roof frame from sun roof panel (see Figure
2F-1).Figure
ZF-1 Separating Sun Roof Frame From SunRoof Panel2. Push detached sun roof frame rearward until it
contacts car roof stop.
NOTE: If difficulty is encountered when pushing
sun roof frame to rear due to the frame hooking into
the sun roof panel, close sun roof until lifters come
into operation. The sun roof frame should now easily
slide rearward.
ADJUSTMENT FRONT OF SUN ROOF
To adjust height of front of sun roof proceed as
follows:
1. Close sun roof.
2. Loosen screws securing front guides to front of sun
roof panel (see Figure
2F-2). Rotate height adjust-
ment ring until desired height is attained.
3. Readjust guides outward so that guides just touch
sides of rails and are not wedged or cocked against
rail sides and tighten screws. Recheck height adjust-
ment.
NOTE: The guides should lightly contact the guideFigure
ZF-2 Sun Roof Front Guide
rail and should have a clearance of no more than 0.02
inch.
ADJUSTMENT. REAR OF SUN ROOF
To adjust height of rear of sun roof proceed as fol-
lows:1. Completely close sun roof and check that the rear
sun roof lifter guides from approximately a 90 degree
angle with respect to the guide rail and that the lifter
contacts the guide stop (see Figure
2F-3). If this is
Figure
2F-3 Rear Sun Roof Lifter 90 Degrees toGuide Rail

ROOF AND SUN ROOF2F-27
not the case, take off crank handle and cable crank
(see Figure 2F-4) and physically reposition lifters to
be approximately 90 degrees to guide rails and to
contact guide stops. Rotate cable crank to its fully
clockwise limit alad reinstall.
Figure 2F-4 Sun Roof Cranking Handle and CableCrank2. Open sun roof until rear lifters lay in a horizontal
position (see Figure
2F-5), loosen lifter pin nut and
turn lifter pin adjusting screw accordingly to lower
or raise lifter pin in slot of lifter.3. Hold lifter pin adjusting screw down and tighten
lifter pin nut.
4. Recheck operation of sun roof and note that lifter
contacts stop when lifter is approximately 90 degrees
to guide rail.
Pull sun roof frame forward and reattach to sun roof
panel.
MAJOR REPAIRREMOVAL AND INSTALLATION OF SUN ROOF
PANEL AND SUN ROOF FRAME
Removal of Sun Roof Panel1. Open sun roof to half open position and pry loose
sun roof frame from sun roof panel (see Figure
2F-1).2. Push detached sun roof frame toward the rear
until it contacts car roof stop.
NOTE: If difficulty is encountered when pushing
sun roof frame rearward due to the frame hooking
into sun roof panel, close sun roof panel completely
and then proceed to push sun roof frame toward rear
of car.
3. Close sun roof panel and then open it approxi-
mately one turn of operating crank.
4. Remove one of two screws holding each of front
Figure
2F-5 Lifter Pin Adjusting Screw
Figure ZF-6 Swinging Front Guide Inboard

2F-281973 OPEL SERVICE MANUAL
guides to height adjustment rings, loosen second
screw (see Figure 2F-6), and swing guides away from
guide rail.
NOTE: When swinging front guides inboard, be
careful not to change position of height adjustment
rings. It is suggested that the position of the height
adjustment rings be marked with a pencil prior to
loosening of front guide attaching screws.
5. Retighten remaining screw holding front guide in
position to prevent height adjustment rings from
turning.
6. Turn lifter guide tension springs 90 degrees in-
board and pull lifters out of sun roof panel brackets
(see Figure
2F-7).Figure
ZF-7 Pulling Rear Lifter Guide out of Sun RoofPanel BracketNOTE: Do not loosen lifter pin nut as this will
change height adjustment on rear of sun roof.
7. Lift out sun roof panel.
Installation of Sun Roof Panel1. Install sun roof panel onto guide rails and locate
panel evenly in stin roof opening.
2. Reposition front guides in original position on
guide rails. Be sure that they squarely contact guide
rails and are not cocked.
NOTE: To achieve proper clearance of front guides
to guide rail, the guides should lightly touch edge ofdshould have a clearance of no
3. Reconnect
riar lifter guides onto sun roof panel
brackets and reposition tension spring as shown in
Figure
2F-3.4. Crank sun roof fully closed and check that the rear
lifters are at approximately 90 degrees with respect
to guide rails and contact guide stops (see Figure
2F-3). If adjustment is required remove crank handle
and cable crank (see Figure 2F-4) and physically
reposition lifters to position described above. Rotate
cable crank to its fully clockwise limit and reinstall.
5. Pull sun roof frame forward and reattach to sun
roof panel.
6. Open and close sun roof several times and recheck
for smoothness of operation.
Removal of Sunlpoof Frame1. Remove sun roof panel.
2. Crank rear lifter guides to furthermost rear posi-
tion.
3. Remove screws securing upper corner plates in
position and lift out upper corner plates (see Figure
2F-8).Figure 2F-&Removing Upper Corner Plates
4. Remove scretii securing left und
r@t guide rai1%lift up front ends
of- guide rails and msert wedge
under forward g&de rail ends. Slide out sun roof
frame.

ROOF AND SUN ROOF2F-29Installation of Sun Roof Frame1. Slide sun roof frame into lower slot of guide rails,
position fully rearward and reattach guide rails to
roof.NOTE: Be sure guide rail retainers at rear of guide
rails are positioned with their dowels in bores of roof
frame.2. Install upper corner plates and secure in place..
3. Install sun roof panel.
REMOVAL AND INSTALLATION OF VELVET STRIP
ON SUN ROOF OPENING, AND VELVET STRIP AND
WEATHERSTRIP ON REAR OF SUN ROOF PANEL
Removal of Velvet Strip on Sun Roof Opening1. Fully open sun roof.
;2. Carefully pull off velvet strip using solvent to dis-
solve cement. Clean area thoroughly before installing
new velvet strip.
Installation of Velvet Strip On Sun Roof Opening1. Cut away for a distance of 1.5 inch the velvet
material on velvet strip that will be on the outside
when strip is cemented in positioAlso cut off to
this dimension the plastic cord i
not cut away velvet material on
1strip which is to be cemented
2. Using
nitrile vinyl trim adhesive (3M Vinyl Trim
Adhesive, Permalastic Viny1 Trim Adhesive or
equivalent) apply sparingly to both sun roof opening
and side of velvet strip to be cemented.
3. Immediately install new velvet strip and position
so that upper edge of velvet strip is flush with car
roof.4. Clean off excess cement being careful not to con-
tact velvet strip.
Removal of Velvet Strip and Wea’therstrip on Rear
of Sun Roof Panel1. Remove sun roof panel.
2. Carefully detach weatherstrip and velvet strip
from sun roof panel using solvent as required todisdolve cement. Thoroughly clean area before in-
stalling new velvet strip and weatherstrip.
Installing Velvet Strip and Weatherstrip On Rear
of Sun Roof Panel1. Using
nitrile vinyl trim adhesive (3M Vinyl Trim
Adhesive Permalastic Viny1 Trim Adhesive or
equivalent) apply sparingly to vertical and horizontal
contact areas at rear of sun roof panel (see Figure
2F-9) and also to side of velvet strip which will touch sun
roof panel.
REAR OF SUN ROOF PANEL
ICAR ROOF
VELVET STRIP
II
,/ WETRSTRIP 1APPLY CEMENT TO HORIZONTAL AND
VERTICAL SURFACES,TO BOTH SIDES
OF VELVET STRIP AND TO SIDE AND
BOTTOM OF WEATHERSTRIP2F-9
Figure
ZF-9 Installing Velvet Strip and Weatherstrip
on Rear of Sun Roof Panel
2. Immediately install new velvet strip and position
so that top edge of velvet strip is flush with sun roof
panel.
3. Apply cement to outboard edge of velvet strip and
to top and bottom contact surfaces of weatherstrip,
and install weatherstrip in position.
4. Clean off excess cement being careful not to con-
tact velvet strip.
5. Install sun roof panel.
REMOVAL AND INSTALLATION OF REAR GUIDES
AND CABLE
Removal of Rear Guides and Cable
1. Remove sun roof panel.
2. Crank rear lifter guides fully rearward and then
remove crank handle and cable crank.