1969 FORD MUSTANG differential

04-02-02

Rear Axle — Removable Carrier Type

04-02-02

COMPONENT INDEX

PINION SPACER (Solid)

Determining Spacer Size

Removal and Installation

REAR WHEEL BEARINGS AND SEALS

Cleaning and Inspection

Removal and Installation

TRACTION-LOK DIFFERENTIAL

Cleaning and Inspection

Description

Disassembly and Overhaul

Removal and Installation

U-JOINT FLANGE

Cleaning and Inspection

Removal and Installation
MODEL APPLICATION
All
Models

02-18

02-18

01-10

02-04

01-10

02-07
Ford
N/A

N/A

N/A

N/A
Mercury
N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

JN/A
Cougar
01-10

02-03

02-22

02-13
Fairlane
01-10

02-03

02-22

02-13
Falcon
01-10

02-03

02-22

02-13
Montego
01-10

02-03

02-22

02-13
Mustang
01-10

02-03

02-22

02-13
Lincoln-
Continental
N/A

02-03

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A
Continental-
Mark
III
N/A

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

1 DESCRIPTION

CONVENTIONAL AXLE

The rear axle is of the banjo-

housing, hypoid gear type using an 8
3/4, 9 or 9 3/8 inch ring gear, in

which the centerline of the pinion is

mounted below the centerline of the

ring gear (Fig. 1).
The pinion gear and the pinion

bearings are assembled in a pinion re-

tainer, which is bolted to the carrier.

The pinion is straddle mounted; that

LEFT AXLE SHAFT

4235

DRIVE PINION

4209

TAPERED ROLLER

BEARINGS 4621

SEAL - 4676

FIG.
1
—
Rear
Axle Assembly—Integral Pinion Gear and Shaft—8-3/4, 9, or 9-3/8 Inch Ring Gear—Typical
procarmanuals.com

04-02-03
Rear Axle — Removable Carrier Type

04-02-03

is,
it is supported by bearings both in

front of and to the rear of the pinion

gear. Two opposed tapered roller

bearings support the pinion shaft in

front of the pinion gear with a col-

lapsible spacer for 8-3/4 inch or 9

inch ring gear, and a solid spacer used

with the 9 3/8 inch ring gear. A

straight roller (pilot) bearing supports

the pinion shaft at the rear of the pi-

nion gear. Pinion and ring gear tooth

contact is adjusted by adding or re-

moving shims from between the pinion

retainer and the carrier housing.

The differential assembly is mount-

ed on two opposed tapered roller

bearings, which are retained in the

carrier by removable caps. The entire

carrier assembly is bolted to the axle

housing.

Ball bearing assemblies (rear wheel

bearings) are pressed onto the outer

ends of the axle shafts and set in the

outer ends of the axle housing. These

bearings support the semi-floating

axle shafts at the outer ends. The

inner ends of the shafts spline to the

differential side gears. Bearing retain-

er plates hold the shafts in the hous-

ing. The left and right axle shafts are

not interchangeable, the left shaft

being shorter than the right.
CASE

COVER

BELLEVILLE

SPRING

CLUTC

HUB
STEEL

PLATES

BONDED

PLATES

E1741-A

FIG. 2—Limited-Slip Differential

LIMITED-SUP DIFFERENTIAL

The axle assembly, except for the

differential case and its internal com-

ponents, is identical to the convention-

al axle.

A constant-friction locking differen-

tial,
which employs clutch plates to

control differential action, is available

as optional equipment (Fig. 2).

Four steel clutch plates are locked

into the differential cover. Three

bronze, bonded clutch plates are

splined to a clutch hub which, in turn,
is splined to the left axle shaft. A

Belleville spring washer maintains a

constant pressure between the steel

and bonded clutch plates so that the

clutch is always engaged.

TRACTION-LOK

DIFFERENTIAL

The Traction-Lok (torque sensitive)

locking differential (Fig. 3) employs a

multiple disc clutch to control differ-

ential action. Shim(s), which control

side gear mounting distance, four

steel, four friction and one composite

plate (steel on one side and friction

material on the other) stacked on a

clutch hub, and four ear guides are

housed in the differential cover. Lo-

cated in the differential case between

the side gears is a one-piece pre-load

plate and block (four-pinion) and four

calibrated pre-load springs, which

apply an initial force to the clutch

pack. Additional clutch capacity is

derived from the side gear thrust

loads.
The four friction plates are

splined to the clutch hub which in turn

is splined to the left axle shaft, and

the eared steel plates are dogged to

the case; thus, the clutch is always en-

gaged.

PINION SHAFT

4211

PINION SHAFT

RETAINING PINS

359475-S
DIFFERENTIAL

CASE-4204

CASE-TO-COVER

RETAINING SCREWS

50025-S2

SIDE GEAR

THRUST WASHER

4228

CENTER BLOCK

(SHORT PINION PINION

SHAFT SEAT) SHAFT

4420 44207
7
PINION GEAR

THRUST WASHER

4230

PINION GEARS

4215

PINION GEAR

THRUST WASHER

4230

PINION SHAFT

44207
SHIM(S)

(AS REQ'D.)

4A324

DIFFERENTIAL

CASE COVER

4204

PINION GEAR

THRUST WASHER

4230
PRE-LOAD SPRING

PINION GEAR PLATE-4A326

THRUST WASHER

4230

CLUTCH PLATE

EAR GUIDES
(4)

4A323

E 1896-A

FIG. 3—Traction-Lok Differentialprocarmanuals.com

04-02-04
Rear Axle — Removable Carrier Type
04-02-04

IN-VEHICLE ADJUSTMENTS AND REPAIRS

REAR AXLE SHAFT, WHEEL

BEARING AND OIL SEAL

REPLACEMENT

The rear axle shafts, wheel bear-

ings,
and oil seal can be replaced

without removing the differential as-

sembly from the axle housing.

REMOVAL OF

AXLE SHAFT

Synthetic wheel bearing seals are

used in production only. Removal and

insertion of rear axle shafts must be

performed with caution. The entire

length of the shaft (including spline)

up to the seal journal must pass

through the seal without cutting of the

seal element during axle removal or

installation will result in early seal fai-

lure.
Leather seals only will be used as

service replacement for synthetic

wheel bearing seals.

1.
Remove the wheel cover, wheel

and tire from the brake drum.

2.
Remove the nuts that secure the

brake drum to the axle shaft flange,

then remove the drum from flange.

3.
Working through the hole pro-

vided in each axle shaft flange, re-

move the nuts that secure the wheel

bearing retainer plate. Then pull the

axle shaft assembly out of the axle

housing (Fig. 4). The brake backing

plate must not be dislodged. Install

one nut to hold the plate in place after

the axle shaft is removed.

Too/-4235-C

E1032-D

FIG. 4—Removing Axle Shaft

REMOVAL OF REAR

WHEEL BEARING AND

SEAL

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvents.

Removal of the wheel bearings from

the axle shaft makes them unfit for

further use.

1.
On all models except Ford, Mer-

cury or Meteor, if the rear wheel

bearing is to be replaced, loosen the

inner retainer ring by nicking it deeply

with a cold chisel in several places

(Fig. 5). It will then slide off easily.
E 1731-A

FIG. 5—Removing Rear Wheel

Bearing Retainer Ring

On Ford, Mercury and Meteor mo-

dels,
it is necessary to first drill a 1/4

inch hole not more than 5/16 inch

deep in the retainer ring surface bef-

ore using the cold chisel.

2.
Remove the bearing from the

axle shaft with the tool shown in Fig.

6 or Fig. 7.

3.
Whenever a rear axle shaft is re-

placed, the oil seal must be replaced.

Remove the seal with Tool 1175-AB

and a slide hammer (Fig. 8). If new

leather-type wheel bearing service

seals are to be installed, soak new oil

seals in SAE 10 oil for 1/2 hour

before installing.

INSTALLATION OF REAR

WHEEL BEARING AND

SEAL

1.
Inspect the machined surface of

the axle shaft and the axle housing for

rough spots or other irregularities

which would affect the sealing action

of the oil seal. Check the axle shaft

splines for burrs, wear or twist. Care-

fully remove any burrs or rough spots.

Replace worn or damaged parts.

2.
Lightly coat wheel bearing bores

with axle lubricant.

3.
Place the retainer plate on the

axle shaft, and press the new wheel

bearing on the shaft with the tool

shown in Fig. 6 or Fig. 9. Do not at-

tempt to press on both the bearing

and the inner retainer ring at the same

time.

4.
Using the bearing installation

tool (Tool 4621-A or 4234-4), press

the bearing inner retainer ring on the

shaft until the retainer seats firmly

against the bearing. On Ford, Mercu-

ry, or Meteor models, before assem-

bling the retainer onto the axle shaft,

the shaft journal and the inside di-
ameter of the retainer should be wiped

clean with a dry cloth. These parts

must not be degreased or lubricated.

5. Rear wheel oil seals with synthe-

tic sealing elements have been incor-

porated in production only. However,

leather seals only will be used as re-

placements for the synthetic sealing

elements. Install the new oil seal with

the tools shown in Figs. 10 and 12. Be

sure the new seal has been soaked in

SAE 10 oil for 1/2 hour before in-

stalling it. Wipe a small amount of oil

resistant sealer on the outer edge of

the seal before it is installed. Do not

put sealer on the sealing lip.

INSTALLATION OF

AXLE SHAFT

1.
Carefully slide the axle shaft into

the housing so that the rough forging

of the shaft will not damage the oil

seal. Start the axle splines into the

side gear, and push the shaft in until

the bearing bottoms in the housing.

2.
Install the bearing retainer plate

and the nuts that secure it. Torque the

nuts to specifications.

3.
Install the brake drum and the

drum attaching (Tinnerman) nuts.

4.
Install the wheel and tire on the

drum. Install the wheel cover.

DRIVE PINION OIL SEAL

REPLACEMENT

COLLAPSIBLE SPACER

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvent.

The drive pinion oil seal can be re-

placed without removing the differen-

tial carrier assembly from the axle

housing.

1.
Raise the vehicle and install

safety stands. Remove both rear wheels

and brake drums.

2.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 11). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission fluidprocarmanuals.com

04-02-08
Rear Axle — Removable Carrier Type

04-02-08

REMOVAL AND INSTALLATION

CARRIER ASSEMBLY

REMOVAL

1.
Raise the vehicle on a hoist and

remove the two rear wheels and tires.

2.
Remove the two brake drums (3

Tinnerman nuts at each drum) from

the axle shaft flange studs. If diffi-

culty is experienced in removing the

drums, remove the brake adjuster

knockout slug or rubber plug (if so

equipped) and back off the brake

shoes.

3.
Working through the hole pro-

vided in each axle shaft flange, re-

move the nuts that secure the rear

wheel bearing retainer plate. Pull each

axle shaft assembly out of the axle

housing using axle shaft remover,

Tool 4235-C. (Fig. 4). Care must be

exercised to prevent damage to the

production-type synthetic oil seal, if so

equipped. Any roughing or cutting of

the seal element during removal or in-

stallation can result in early seal fail-

ure.
Install a nut on one of the brake

backing plate attaching bolts to hold

the plate to the axle housing after the

shaft has been removed. Whenever a

rear axle shaft is replaced, the wheel

bearing oil seals must be replaced.

Remove the seals with tool 1175AB.

4.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position at as-

sembly. Disconnect the drive shaft at

the rear axle U-joint. Hold the cups

on the spider with tape. Mark the

cups so that they will be in their orig-

inal position relative to the flange

when they are assembled. Remove the

drive shaft from the transmission ex-

tension housing. Install an oil seal re-

placer tool in the housing to prevent

transmission leakage. Refer to the

transmission group for the appropriate

tool.

5.
Clean area around carrier to

housing surfaced with a wire brush and

wipe clean, to prevent dirt entry into

the housing. Place a drain pan under

the carrier and housing, remove the

carrier attaching nuts, and drain the

axle.
Remove the carrier assembly

from the axle housing.

INSTALLATION

Synthetic production-type wheel

bearing seals must not be cleaned,

soaked or washed in cleaning solvent.

1.
Clean the axle housing and

shafts using kerosene and swabs. To

avoid contamination of the grease in
the sealed ball bearings, do not allow

any quantity of solvent directly on the

wheel bearings. Clean the mating sur-

faces of the axle housing and carrier.

2.
Position the differential carrier

on the studs in the axle housing using

a new gasket between carrier and

housing. Install the carrier-to-housing

attaching nuts, and torque them to

specifications.

3.
Remove the oil seal replacer tool

from the transmission extension hous-

ing. Position the drive shaft so that

the front U-joint slip yoke splines to

the transmission output shaft.

4.
Connect the drive shaft to the

axle U-joint flange, aligning the scribe

marks made on the drive shaft end

yoke and the axle U-joint flange dur-

ing the removal procedure. Install the

U-bolts and nuts and torque to speci-

fications.

5.
If the synthetic, production-type

wheel bearing seals were replaced with

service-type leather seals, soak the

new rear wheel bearing oil seals in

SAE 10 oil for 1/2 hour before instal-

lation. Wipe a small amount of an oil

resistant sealer on the outer edge of

each seal before it is installed. Do not

put any of the sealer on the sealing

lip.
Install the oil seals in the ends of

the rear axle housing with one of the

tools shown in Figs. 10 and 12.

Tool

T65F-1177.A

E 1571-A

FIG. 12—Rear Axle Shaft Bearing

Seal Installation

6. Install the two axle shaft assem-

blies in the axle housing. Care must

be exercised to prevent damage to the

oil seals. The shorter shaft goes into

the left side of the housing.

Carefully slide the axle shaft into

the housing so that the rough forging

of the shaft will not damage the oil

seal. Start the axle splines into the

differential side gear, and push the

shaft in until the bearing bottoms in

the housing.
7.
Install the bearing retainers on

the attaching bolts on the axle housing

flanges. Install the nuts on the bolts

and torque to specifications.

8. If the rear brake shoes were

backed off, adjust the brakes as out-

lined in Part 2-1 and install rubber

plugs in the adjuster slots.

9. Install the two rear brake drums

and the drum Tinnerman nuts.

10.
Install the rear wheels and tires.

11.
Fill the rear axle with specified

lubricant.

AXLE HOUSING (COIL

SPRING SUSPENSION)

REMOVAL

1.
Remove the carrier assembly

from the axle housing as outlined in

Differential Carrier Removal and In-

stallation.

2.
Position safety stands under the

frame rear members, and support the

axle housing with either a floor jack

or hoist.

3.
Disengage the brake line from

the clips that retain the line to the

axle housing.

4.
Disconnect the vent tube from

the rear axle housing.

5.
Remove the brake backing plate

assemblies from the axle housing, and

support them with wire. Do not dis-

connect the brake line.

6. Disconnect the lower studs of the

two rear shock absorbers from the

mounting brackets on the axle housing

(Fig. 13 and 14).

7.
Remove the attaching nut and

washer, and disconnect the track bar

from the mounting stud on the axle

housing bracket.

8. Lower the axle housing until the

coil springs are released. Lift out the

coil springs and insulators.

9. Remove the nuts, washers and

pivot bolts that connect the suspension

lower arms to the axle housing. Dis-

connect both arms from the axle

housing.

10.
Disconnect the upper suspen-

sion arm from the axle housing by re-

moving the pivot bolt, nut, lock wash-

er and the two eccentric washers (Fig.

13 and 14).

11.
Lower the axle housing and re-

move it from under the vehicle.

INSTALLATION

1.
Transfer the track bar mounting

stud from the old to the new housing.procarmanuals.com

04-02-11
Rear Axle — Removable Carrier Type

04-02-11

If the axle housing is new, install a

new vent. The hose attaching portion

must face toward the front of the ve-

hicle.

2.
If leather-type wheel bearing ser-

vice seals are to be installed, soak the

new rear wheel bearing oil seals in

SAE 10 oil for 1/2 hour before instal-

lation. Wipe a small amount of an oil

resistant sealer on the outer edge of

each seal before it is installed. Do not

put any of the sealer on the sealing

lip.
Install the oil seals in the ends of

the axle housing with one of the tools

shown in Fig. 10 and 12.

3.
Position the replacement axle

housing under the vehicle, and raise

the axle with a hoist or floor jack.

Connect the suspension lower arms to

their mounting brackets on the axle

housing with pivot bolts and nuts. Do

not tighten the bolts and nuts at this

point.

4.
Position the suspension upper

arm in its mounting bracket on the

axle housing, and install the adjusting

bolt, eccentric washers, lock washer

and nut. Leave the bolt and nut loose

at this point.

5.
Position the brake lines to the

axle housing, and secure with the re-

taining clips.

6. Install the brake backing plates

on the axle housing flanges.

7.
Connect the track bar to the

mounting stud, install the washer and

attaching nut, and torque to specifica-

tions.

8. Position the rear coil springs and

insulators in the pockets provided.

9. Connect the lower studs of the

two rear shock absorbers to the

mounting brackets on the axle hous-

ing. Install the attaching nuts, and

torque to specifications.

10.
Connect the vent tube to the

vent on the housing. If axle housing is

new, install a new vent.

11.
Clean the mating surfaces of

the axle housing and differential car-

rier. Position the carrier on the

mounting studs on the housing using a

new gasket between carrier and hous-

ing. Install the copper washers and the

carrier-to-housing attaching nuts, and

torque to specifications.

12.
Make sure that both the front

and rear pivot bolts of the upper and

the two lower arms are loose, and

then raise the axle assembly to con-

trolled curb height (Fig. 15). Hold the

axle at controlled curb height by plac-

ing blocks or pieces of steel pipe be-

tween the axle housing and the bumper

rear screw on the side rail. (See speci-

fications for dimensions.)
FRAME

TIGHTEN ARM

ATTACHING BOLTS

AT 5-45/64 INCH

HEIGHT POSITION
5-45/64 INCH

HEIGHT FOR

INSTALLATION

OF ARMS

E 1600-B

FIG. 75 -Axle Normal Curb

Height and Controlled Height

for Arm Installation

13.
With the axle at controlled curb

height, torque the suspension upper

and lower arm front pivot bolts and

nuts to specifications. Torque the

lower arm-to-axle housing pivot bolts

and nuts to specifications.

14.
Remove the oil seal replacer

tool from the transmission extension

housing. Position the drive shaft so

that the front U-joint slip yoke splines

to the transmission output shaft.

15.
Connect the drive shaft to the

U-joint flange, aligning the scribe

marks made on the drive shaft end

yoke and the axle U-joint flange dur-

ing the removal procedure. Install the

U-bolts and nuts and torque to speci-

fications.

16.
Carefully slide the two axle

shaft assemblies in the axle housing.

The shorter shaft goes into the left

side of the housing. Use care in slid-

ing the axle shafts into the housing so

that the rough forging of the shaft will

not damage the oil seal. Start the axle

splines into the differential side gear,

and push the shaft in until the rear

wheel bearing bottoms in the housing.

17.
Install the rear wheel bearing

retainers on the attaching bolts on the

axle housing flanges. Install the nuts

on the bolts and torque to specifica-

tions.

18.
If the rear brake shoes were

backed off, adjust the brakes as out-

lined in Part 2-1, and install rubber

plugs in the adjuster slots.

19.
Install the two rear brake

drums and the drum attaching (Tin-

nerman) nuts.

20.
Install the rear wheels and tires.

21.
Fill the rear axle to the bottom

of the filler plug hole located in either

the carrier casting or housing cover

with specified lubricant. Be sure that

the axle is in operating position.

22.
Road test the vehicle to be sure

that pinion and driveshaft angles are
correct. Any shudder during heavy ac-

celeration, or deceleration may require

a pinion and driveshaft angle re-

adjustment as detailed in Driveshaft

and Pinion Angle Adjustment, Group

3,
Part 3-2.

AXLE HOUSING (LEAF

SPRING SUSPENSION)

REMOVAL

1.
Raise the vehicle and support it

with safety stands under the rear

frame member.

2.
Drain the lubricant from the

axle.

3.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly. Disconnect

the drive shaft at the drive pinion

flange.

4.
Disconnect the lower end of the

shock absorbers.

5.
Remove the wheels, brake drums

and both axle shafts as outlined in

Section 2.

6. Remove vent hose front vent

tube (Corbin clamp) and remove vent

tube from brake tube junction and

axle housing.

7.
Remove the hydraulic brake T-

fitting from the axle housing. Do not

open the hydraulic brake system lines.

Remove the hydraulic brake line from

its retaining clip on the axle housing.

8. Remove both axle shaft oil seals

with the tool shown in Fig. 8.

9. Remove both brake backing

plates from the axle housing and sus-

pend them above the housing with

mechanic's wire. The hydraulic brake

lines and the parking brake cables are

still attached to the brake backing

plates.

10.
Support the rear axle housing

on a jack, and then remove the spring

clip nuts. Remove the spring clip

plates (Fig. 16).

11.
Lower the axle housing and re-

move it from under the vehicle.

12.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. See

Section 4, Major Repair Operation*.

INSTALLATION

1.
Raise the axle housing into posi-

tion so that the spring clip plates can

be installed. On a Montego or Fair-

lane,
position the spring upper insula-

tors and retainers between the axle

housing and springs and install theprocarmanuals.com

04-02-13

Rear Axle
—
Removable Carrier Type
04-02-13

lower insulators. Torque
the
spring

clip nuts
to
specification.

2.
Place
the
brake backing plates
in

their normal position
on the
axle

housing.

3.
Install
new
axle shaft
oil
seals

with
the
tool shown
in Fig. 10.
Soak

the
new
seals
in
light weight engine
oil

(SAE
10) for 1/2
hour before install-

ing them. Installation without
use of

the proper tool will distort
the
seal

and cause leakage. Coat
the
outside
edges
of the new oil
seal with
a non-

hardening type
of
sealer such
as Per-

matex
No. 2 or its
equivalent.

4.
Install
the
axle shafts, brake

drums
and
wheels
as
outlined
in Sec-

tion
2.

5.
Attach
the
hydraulic brake line

T fitting
to the
axle housing,
and se-

cure
the
hydraulic brake line
in its re-

tainer
on the
axle housing.

6. Install vent tube
to
brake tube

junction
and
install vent hose
to
vent
tube.

7.
Raise
the
axle housing
and con-

nect
the
shock absorbers.

8. Connect
the
rear
end of the
drive

shaft
to the
axle U-joint flange, align-

ing
the
scribe marks made
on the

drive shaft
end
yoke
and the
axle
U-

joint flange.

9. Fill
the
axle with
the
proper

grade
and
amount
of
lubricant.

10.
Road test
the
vehicle.

MAJOR REPAIR OPERATIONS

DISASSEMBLY
OF

DIFFERENTIAL CARRIER

CONVENTIONAL

DIFFERENTIAL

A disassembled view
of the
rear

axle assembly
is
shown
in Fig. 17.

After mounting
the
carrier
in a

holding fixture, disassemble
the car-

rier
as
outlined
in the
following proce-

dures:

1.
Mark
one
differential bearing

cap
and the
mating bearing support

with punch marks
to
help position
the

parts properly during assembly
of the

carrier. Also, mark
one of the
bearing

adjusting nuts
and the
carrier with

AXLE SHAFT-4725
RETAINER RING-1100
scribe marks
for
proper location
dur-

ing assembly.

2.
Remove
the
adjusting
nut
locks,

bearing caps,
and
adjusting nuts. Then

lift
the
differential case assembly
out

of
the
carrier.

(Remove
the
bearing caps
by tap-

ping
the
caps lightly with
a
soft
mal-

let).

3.
Remove
the
differential bearings

with
the
tools shown
in Fig. 18.

4.
Mark
the
differential case, cover,

and ring gear
for
assembly
in the
orig-

inal position.

5.
Remove
the
bolts that attach
the

ring gear
to the
differential case. Press

the gear from
the
case
or tap it off

with
a
soft-faced hammer.

6. With
a
drift, drive
out the
differ-

AXLE HOUSING-4010

DIFFERENTIAL

PINION SHAFT-4211
ential pinion shaft lock
pin (Fig. 19),

and separate
the
2-piece differential

case.

7.
Drive
out the
pinion shaft with
a

brass drift
(Fig. 20).

8. Remove
the
gears
and
thrust

washers
(Fig. 48).

LIMITED-SLIP DIFFERENTIAL

1.
Remove
the
differential case

from
the
carrier
and
remove
the
bear-

ings from
the
differential case
in the

same manner
as the
conventional
dif-

ferential case.

2.
Place
the
differential case
in a

hydraulic press,
and
apply about
one

ton pressure across
the
case bearing

hubs while removing
the
ring gear
at-

FLAT WASHER (LIMITED SLIP ONLY)

DRIVE GEAR ATTACHING BOLT

DIFFERENTIAL CASE COVER -4206

DIFFERENTIAL PINION GEAR-4215

THRUST WASHER-4230

ADJUSTING NUT-4067

CARRIER HOUSING-4025

DRIVE PINION-4610
PINION BEARING

SPACER-4662

PINION FRONT

BEARING-4621

RING GEAR

PILOT BEARING-4A242

FIG. 17—Rear Axle Disassembled—Typical
PILOT BEARING

RETAINER-4627

PINION REAR

BEARING CUP-4616
DEFLECTOR-4859

PINION RETAINER-4668

SEAL-4676
FLANGE_4858
E1750-Aprocarmanuals.com

04-02-14

Rear Axle
—
Removable Carrier Type

04-02-14

DIFFERENTIAL

BEARING
Tool—
7
571-4220-A

T66P°4220-P

E1015-B

FIG. 18—Removing Differential

Bearing—Ford

taching bolts. Applying pressure will

contain
the
spring pressure between

the differential case
and
cover until

after
the
bolts
are
removed,
and
there-

by prevent stripping
of the
threads.

3.
Release
the
hydraulic press
ram,

and remove differential case cover.

4.
Remove
the
Belleville spring

(Fig.
54).

5.
Remove
the
steel
and the
bonded

clutch plates.

6. Remove
the
differential clutch

hub,
side gear,
and
thrust washer.

7.
Remove
the
ring gear from
the

differential case.

8. Drive
out the
differential pinion

shaft lock
pin.

9. With
a
brass drift, drive
out the

differential pinion shaft. Then remove

the pinion gears,
the
other side gear,

and thrust washers.
E 1724-A

FIG. 20—Driving
Out
Differential

Pinion Shaft

TRACTION-LOK

DIFFERENTIAL

1.
Remove
the
differential case

from
the
carrier
and
remove
the
bear-

ings from
the
differential case
in the

same manner
as the
conventional
dif-

ferential case.

2.
Remove
ten
bolts securing
the

ring gear
to the
differential case
as-

sembly.
The
ring gear must
be re-

moved
in
order
to
separate
the
case

halves.

3.
Remove
the
ring gear
by
tapping

the gear with
a
soft hammer
or
press

the gear from
the
case.

4.
Place
the
differential case
in a

press
to
load
the
bearing journals
so

that
the
pre-load
of the
springs
is ov-

ercome (approx.
1,500
lbs.).
(If a

press
is not
available,
two 7/16
inch

bolts
and
nuts
can be
used
in the
ring

gear mounting holes
(one on
each

side)
to
compress
the
case halves
to-
gether
and
overcome pre-load spring

tension.) Then, while
the
case
is
still

under pressure, loosen
the two
Allen

or Phillips head screws which hold
the

case halves together until
one or two

threads
of the
screws remain engaged.

Remove
the
case assembly from
the

press.
Tap on the
cover
to
spring
it

loose; then, remove both screws.

5.
With
the
cover facing down, lift

off
the
case. Remove
the
pre-load

spring plate
and
four pre-load springs.

6. From
the
cover remove
the
side

gear, four clutch plate
ear
guides,

clutch
hub,
friction
and
steel clutch

plates
and
shim(s).

7.
With
a
suitable drift, drive
out

the pinion shaft lock pins from
the

case.

8. With
a
brass drift, drive
out the

long pinion shaft from
the
case. Drive

from
the end
opposite
the
lock
pin

hole.

9. Remove
the two
short pinion

shafts using
a
drift, driving each shaft

from
the
center outward. Lift
out the

center block, then remove
the
pinion

gears,
thrust washers
and
side gear

and thrust washer.

10.
If the
differential bearings
are

removed,
the
bearings
can be
installed

in
one of the
following ways:

a. With
the
differential case
and

cover completely assembled.

b.
On the
case
or
cover when disas-

sembled. However, when pressing
the

bearings
on the
cover,
a
block
of

wood
or
fiber must
be
used
as
shown

in Fig.
21 in
order
to
avoid damage
to

the cover.

E 1709-A

FIG. 79—Removing Differential

Pinion Shaft Lock
Pin
DIFFERENTIAL BEARING

E1892-A

FIG. 21—Installing Differential Bearing—Traction-Lokprocarmanuals.com

04-02-16

Rear Axle — Removable Carrier Type
04-02-16

Tool~T53L-200-A

Tool-T57L-4625-A

or 4625-K

E 1725-A

FIG. 29—Removing Pilot Bearing

to adjust for individual variations in

both the carrier housing dimension

and in the original gear set dimension.

Therefore, to select the correct shim

thickness for the new gear set to be

installed, follow these steps:

1.
Use a micrometer to measure

the thickness of the original shim re-

moved from the axle and use the same

thickness upon installation of the re-

placement carrier assembly or drive

pinion. If further shim change is ne-

cessary, it will be indicated in the

tooth pattern check.

2.
If the original shim is lost, sub-

stitute a nominal shim for the original

and use the tooth pattern check to

determine if further shim changes are

required. Nominal shim thicknesses is

E 1734-A
PINION BEARING

RETAINER

E 1482-B

FIG. 31—Removing Pinion Front

Bearing Cup

indicated in Part 4-3, Specifications.

A new ring gear and pinion should

always be installed in an axle as a

matched set (never separately). Be

sure the same identifying (matching)

number, appears on the bolt hole face

of the ring gear and on the head of

the drive pinion (Fig. 35).

3.
After determining the correct

shim thickness as explained in the

ss
Rom

Too/-T58L-70?-A

or4675-J

FIG. 30—Removing Pinion Front

Bearing Cup
FIG. 32—Removing Pinion Rear

Bearing Cup

foregoing steps, install the new pinion

and ring gear as outlined under As-

sembly.

DIFFERENTIAL
CASE

BEARINGS
AND
RING

GEAR
TEST

If the ring gear runout check (be-

fore disassembly) exceeded specifica-

tions,
the condition may be caused by

a warped gear, a defective case, or ex-

cessively worn differential bearings.

To determine the cause of excessive

runout proceed as follows:

1.
Assemble the two halves of the

differential case together without the

ring gear, and press the two differen-

tial side bearings on the hubs.
Press Ram

Tool -

T57L - 4614-A
Tool -

T57L - 4676-A2

1736-/

FIG. 33—Installing Pinion Front

Bearing Cup

too;-
IB .

T55P-46U
A2V •H"^^

\
Press Ram

Tool-

T57L-46U-A

FIG. 34—Installing Pinion Rear

Bearing Cup

2.
Place the cups on the bearings

and set the differential case in the car-

rier.

3.
Install the bearing caps and ad-

justing nuts as outlined in Steps 11

thru 14 under Assembly and Installa-

tion of Conventional Differential Case

which follows in this section.

4.
Tighten the right nut two notches

beyond the position where it first con-

tacts the bearing cup. Rotate the dif-

ferential case several revolutions in

each direction while the bearings are

MATCHED

GEAR SET

IDENTIFICATION

E 1628-A

FIG. 35— Pinion and Ring Gear

Markingsprocarmanuals.com