1969 FORD MUSTANG lights

07-02-06
C4 Automatic Transmission

07-02-06

PLUG-7256
•HANDLE-7217

BUTTON-7C439

DIAL HOUSING

ASSEMBLY-7E034

POINTER BACK-UP

SHIELD

ENGAGE FLATS OF STUD IN SLOT OF

ROD BEFORE APPLYING TORQUE

D2022-A

FIG. 8—Manual Linkage—Console Shift—Mustang

ACTUATOR LEVER ATTACHING BOLT

D1812-A

FIG. 9—Neutral Start Switch Adjustments—Console Shift—Ford-Meteor

9. Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.
10.
Place the console top panel on

the console and install the retaining

screws.

11.
Position the selector lever de-

tent control and handle on the selector
lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
With the manual linkage proper-

ly adjusted, check the starter en-

gagement circuit in all positions. The

circuit must be open in all drive posi-

tions and closed only in park and neu-

tral.

Gauge Pin

(No.43 Drill)

NEUTRAL START

SWITCH

Dl759-A

70—Neutral Start Switch

Adjustments—Console Shift—

Fairlane-Montegoprocarmanuals.com

07-02-07
C4 Automatic Transmission

07-02-07

2.
Remove the selector lever handle

from the lever.

3.
Remove the trim panel from the

top of the console.

4.
Remove the cover and dial indi-

cator as an assembly.

5.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

6. Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 10).

7.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG

1.
With the manual lever properly

NEUTRAL
START

SWITCH

(D1439-A

FIG. 11—Neutral Start Switch

Adjustments—Console Shift—

Mustang
adjusted, loosen the two switch attach-

ing bolts (Fig. 11).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 11).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE SHIFT

On vehicles equipped with a column

mounted neutral start switch, refer to

Part 7-1, Section 2, for the replace-

ment procedures.

FORD-METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 9).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle

MUSTANG

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 11).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 11).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.procarmanuals.com

07-03-07
FMX Transmission

07-03-07

Gauge Pin

(No.
43 Drill)

NEUTRAL START

SWITCH

ADJUSTMENT

SCREWS

D 1759-A

FIG. 8—
Neutral
Start Switch-

Console Shift—Fairlane-Montego

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
With the manual linkage proper-

ly adjusted and the engine turned off,

place the selector lever in the N (Neu-

tral) position. Then, shift the selector

lever from neutral to 1, to P (park)

and back to neutral. Shifting the se-

lector lever through this shift pattern

should adjust the switch automatical-

ly. If not, adjust it manually as fol-

lows:

2.
With the selector lever in neu-

tral,
remove the selector lever handle

attaching screw and remove the

handle (Fig. 7).

3.
Remove the dial housing attach-

ing screws and remove the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.
NEUTRAL START SWITCH

AND HARNESS ASSEMBLY

32027-A

FIG. 9—Neutral Start Switch—Console Shift—Mustang-Cougar

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing.

6. Lift the switch from the housing

and move the actuator lever all the

way to the left. Then, return the actu-

ator lever to the neutral position as

shown in Figure 9.

7.
Position the neutral switch as-

sembly to the selector lever housing,

and secure with the two attaching

screws.

8. Place the selector lever in the P

(Park) position and check the opera-

tion of the switch. The engine should

start with the selector lever in the

park position. If the engine does not

start, replace the switch. Refer to the

Neutral Start Switch Replacement

procedures in this section.

9. Install the pointer back-up shield

on the housing and lever assembly.

10.
Install the dial housing on the

selector lever housing assembly.

11.
Install the selector lever.'handle.

NEUTRAL START SWITCH

REPLACEMENT-

CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

replacement procedures.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 8).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.procarmanuals.com

07-04-06
C-6 Automatic Transmission
0704-06

TRANSMISSION

MANUAL LEVER

STUD-7B415

ENGAGE FLATS OF STUD IN SLOT OF

ROD BEFORE APPLYING TORQUE

FIG. 6—Manual Linkage—Column Shift—Lincoln Continental

INNER BRACKET-7C431

TRANSMISSION

MANUAL LEVER

ROD-7326

SHIFT ROD-7A024

ENGAGE FLAT OF STUD IN SLOT
OF

ROD BEFORE APPLYING TORQUE
POINT A

BRACKET ASSEMBLY-7C324

D1831-A

FIG.
7—Manual
Linkage—Column Shift—Thunderbird-Continental Mark
III

the switch lever contacts
the
selector

lever actuator.
If an
adjustment
can

not
be
made
by
rotating
the
switch,

loosen
the
actuator lever attaching

bolt
and
adjust
the
lever (Fig.
11).

8. Tighten
the
neutral start switch

attaching screws.
If the
actuator lever
was adjusted, tighten
the
actuator

lever bolt.

9. Turn
the
ignition
key to the

ACC position
and
place
the
selector

lever
in the
reverse position
and
check

the operation
of the
back-up lights.

Turn
the key off.
D2033-A

10.
Place
the
console
top
panel
on

the console
and
install
the
retaining

screws.

11.
Position
the
selector lever
de-

tent control
and
handle
on the
selector

lever
and
secure with
the
four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
With
the
manual linkage proper-

ly adjusted, check
the
starter
en-

gagement circuit
in all
positions.
The

circuit must
be
open
in all
drive posi-

tions
and
closed only
in
park
and neu-

tral.

2.
Remove
the
selector lever handle

from
the
lever.

3.
Remove
the
trim panel from
the

top
of the
console.

4.
Remove
the
cover
and
dial indi-

cator
as an
assembly.

5.
Remove
the six
screws that
se-

cure
the
selector lever retainer
to the

selector lever housing. Lift
the
retainer

from
the
housing.

6. Loosen
the two
combination

starter neutral
and
back-up light

switch attaching screws (Fig.
12).

7.
Move
the
selector lever back
and

forth until
the
gauge
pin
(No.
43
drill)

can
be
fully inserted into
the
gauge

pin holes (Fig.
12).

8. Place
the
transmission selector

lever firmly against
the
stop
of the

neutral detent position.procarmanuals.com

07-04-08
C-6 Automatic Transmission

07-04-08

PLUG-7256
•

•HANDLE-7217

I DIAL HOUS NG

ASSEMBLY-7E034

POINTER BACK-JP

SHIELD
HOUSING AND LEVER

ASSEMBLY-7C453

ENGAGE FLATS OF STUD IN SLOT OF

ROD BEFORE APPLYING TORQUE

D2034-A

FIG. 10—Manual Linkage—Console Shift—Mustang-Cougar

ACTUATOR LEVER ATTACHING BOLT

Gauge Pin

(No.
43 Drill)

NEUTRAL START

SWITCH

D1812-A

FIG. 11—Neutral Start Switch Adjustments—Console Shift

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.
Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.
FIG. 72—Neutral Start Switch

Adjustment—Console Shift—

Fairlane-Montego

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the six attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.procarmanuals.com