1969 FORD MUSTANG light

02-02-30
Brake System

02-02-30

7.
Disconnect the wire lead at the

parking brake warning light switch

and remove the control assembly.

Installation

1.
Connect the wire lead to the

parking brake warning light switch.

2.
Position the control assembly to

the cowl inner side panel and install

the three attaching screws.

3.
Connect the ball-end of the park-

ing brake front cable assembly to the

control assembly, and install the hair-

pin retainer.

4.
Position the cable ball in the

notch in the brake clevis.

5.
Position the left air vent assem-

bly to the dash and instrument panels.

Install the four bolts and one nut re-

taining the air vent to the panels.

6. Check the operation of the park-

ing brake. Adjust the parking brake.

MUSTANG AND COUGAR

Removal

Refer to Fig. 36.

1.
Make sure the parking brake is

completely released,

2.
Remove all tension from the rear

cables by backing off the jam nut and

adjusting nut from the equalizer.

3.
Disconnect the wire lead at the

parking brake warning light switch (if

so equipped).

4.
Remove the parking brake front

cable ball retaining clip from the clev-

is.

5.
Remove the parking brake warn-

ing light switch and attaching screw (if

so equipped).

6. Disconnect the cable ball from

the notch in the brake clevis.

7.
Remove the three screws that at-

tach the control assembly to the left

cowl inner side panel.

8. Pull the control away from the

cowl, panel. Remove the hair-pin re-

tainer securing the front cable assem-

bly to the control assembly. Remove

the control assembly

Installation

1.
Connect the ball-end of the park-

ing brake front cable assembly to the

control assembly, and install the hair-

pin retainer.

2.
Position the control assembly to

the cowl inner side panel and install

the three attaching screws.
3.
Position the parking brake warn-

ing light switch and install the attach-

ing screw. Connect the parking brake

warning light switch wire lead (if vehi-

cle is so equipped).

4.
Position the cable ball in the

notch in the brake clevis.

5.
Check the operation of the park

ing brake. Adjust the parking brake.

THUNDERBIRD AND

CONTINENTAL MARK III

Removal

Refer to Fig. 37.

1.
Remove the two nuts retaining

the control to the dash panel.

2.
Remove two screws from the left

scuff plate.

3.
Remove one screw retaining the

left cowl trim panel and remove the

panel.

4.
Remove the two screws retaining

the left air duct and remove the air

duct.

5.
Remove the two screws retaining

the dimmer switch and position the

switch out of the way.

6. Remove the clip retaining the

cable assembly to the control.

7.
Disconnect the cable ball from

the control clevis.

8. Disconnect the vacuum hose at

the brake release.

9. Remove the bolt retaining the

control to the cowl side bracket and

remove the control.

Installation

1.
Position the parking brake con-

trol in the vehicle.

2.
Install the cable assembly in the

control and connect the cable ball to

the control clevis.

3.
Install the clip retaining the

cable to the control.

4.
Install the bolt retaining the con-

trol to the cowl side bracket.

5.
Connect the vacuum hose to the

parking brake release vacuum motor.

6. Position the dimmer switch and

install the retaining screws.

7.
Position the air duct and install

the retaining screws.

8. Position the cowl trim panel and

install the retaining screw.

9. Install the two scuff plate screws.

10.
Install the two nuts retaining

the control to the dash panel.

11.
Adjust the parking brakf
LINCOLN CONTINENTAL

Removal

Refer to Fig. 38.

1.
Raise the vehicle on a hoist.

2.
Loosen the parking brake cable

adjusting nut, remove the return

spring and remove the cable ball end

from the equalizer.

3.
Lower the vehicle.

4.
Disconnect the battery.

5.
Disconnect the wire harness con-

nector and two vacuum hoses at the

Automatic Temperature Control box.

6. Working inside the vehicle, re-

move the windshield wiper control

knob and bezel from the lower control

panel.

7.
Remove the screws retaining the

lower control panel. Lower the control

panel and disconnect wire harnesses

and vacuum hoses. Position the con-

trol panel aside.

8. Remove the screw retaining the

plastic wire cover and place 'the cover

aside.

9. Disconnect three vacuum hoses

and the wiring harness at the Auto-

matic Temperature Control box.

10.
Remove the two screws retain-

ing the Automatic Temperature Con-

trol box to the dash panel and remove

the box for clearance.

11.
Disconnect the ball end of the

cable from the control clevis.

12.
Remove the four bolts retaining

the control to the dash panel and

lower instrument panel flange.

13.
Disconnect the vacuum release

hose from the control and remove the

control assembly from the vehicle.

Installation

1.
Position the control assembly to

the dash panel and instrument panel

flange and install the four retaining

screws.

2.
Connect the vacuum release hose

to the control assembly.

3.
Connect the cable ball to the

control clevis.

4.
Position the Automatic Temper-

ature Control box to the dash panel

and install the retaining screws.

5.
Connect the wiring harness and

vacuum hoses to the Automatic Tem-

perature Control box.

6. Position the plastic wire covei

and install the retaining screw.

7.
Connect the wire harnesses and

vacuum lines to the lower control

panel and position the panel to the inprocarmanuals.com

02-02-38
Brake System

02-02-38

2.
Disconnect the actuator solenoid

and warning switch harness connectors

from the control module.

3.
Remove the two wiring harness

grommets from the dash panel and

push the wiring harness and connec-

tors through the openings in the dash

panel.

4.
Working in the engine compart-

ment loosen the hose clamp and re-

move the air hose from the air filter.

5.
Remove the engine air cleaner-

Loosen the hose clamp and remove

the vacuum hose from the vacuum

manifold fitting.

6. Raise the vehicle on a hoist.

7.
Disconnect the exhaust pipes

from the exhaust manifold and sup-

port with wire to provide access to the

actuator assembly.

8. Remove the bolt retaining the

actuator ground wire to the rear outer

corner of the engine right bank.

9. Loosen the tube nuts and discon-

nect the brake system hydraulic tubes

from the hydraulic valve housing.

10.
Remove the three nuts retaining

the actuator assembly to the actuator

support bracket.

11.
Remove the three bolts that re-

tain the actuator mounting bracket to

the side rail and remove the mounting

bracket.

12.
Remove the actuator assembly

from the vehicle and place it on a

bench.

13.
Remove the air and vacuum

hoses from the actuator.

INSTALLATION

1.
Install the air and vacuum hoses

on the new actuator.

2.
Place the actuator assembly into

position under the vehicle, routing the

air and vacuum hoses up between the

engine and fender apron and inserting

the solenoid leads through the holes in

the firewall.

3.
Position the ground wire to the

rear of the engine block and install re-

taining bolt.

4.
Position the actuator mounting

bracket to the frame side rail and in-

stall the three retaining bolts.

5.
Position the actuator assembly

to the mounting bracket and install

the three retaining nuts.

6. Connect the hydraulic tubes to

the hydraulic valve assembly and

tighten the tube nuts to specifications.

7.
Connect the exhaust pipes to the

exhaust manifolds.

8. Lower the vehicle.

9. Pull the actuator solenoid and

brake warning switch wiring harness
through the two holes in the dash

panel from inside the car. Seat the

wiring harness grommets in the dash

panel.

10.
Connect the actuator solenoid

and brake warning switch wiring har-

ness connectors to the control mo-

dules.
'

11.
Position the control module in

the bracket under the glove box and

install the retaining screw.

12.
In the engine compartment con-

nect the air hose to the air filter and

position the hose clamp.

13.
Connect the vacuum hose to the

engine vacuum manifold fitting. In-

stall the engine air cleaner.

14.
Bleed the rear brake system and

centralize the pressure differential

valve.

15.
Raise the rear wheels. Apply

the brakes with the rear wheels turn-

ing to verify proper operation of the

anti-skid control system.

ANTI-SKID CONTROL MODULE

REMOVAL

Refer to Fig. 39.

1.
Remove the retaining strap hold-

ing the harnesses.

2.
Remove the screw that attaches

the forward end of the control module

retainer to the support assembly.

3.
Lower the forward end of the

control module and retainer from the

support assembly; move the module

and retainer forward slightly until the

flange clears the slot in the support

assembly.

4.
Disconnect the five wiring har-

ness plugs from the control module.

5.
Remove the control module from

the vehicle.

INSTALLATION

1.
Connect the five wiring harness

plugs to the control module. Only one

arrangement is possible.

2.
Position the control module in

the retainer, orienting the module per

the markings on it, and insert the re-

tainer flange into the slot at the rear

of the support assembly.

3.
Pivot the retainer and control

module upward and align the screw

hole in the forward end of the retainer

with the hole in the support bracket

assembly. Install the retaining screw.

4.
Test the vehicle on the hoist to

verify correct operation of the skid

control system.
5.-
Secure the wiring to the module

support extension with the retaining

strap.

ANTI-SKID CONTROL SENSOR

REMOVAL

Refer to Fig. 39.

1.
Raise the vehicle on a hoist.

2.
Remove the rear wheel and tire

assembly.

3.
Remove the three Tinnerman

nuts (3) and remove the brake drum.

4.
Disconnect the sensor lead from

the rear wiring harness.

5.
Unseat the sensor lead grommet

pushing it to the inside of the brake

assembly.

6. Remove the four nuts that retain

the sensor to the backing plate and

pull the axle shaft, sensor assembly

and wheel bearing assembly from the

axle housing.

7.
Press the wheel bearing retainer

and wheel bearing off the axle shaft

(Refer to Part 4-2).

8. Remove the sensor assembly and

press the rotor off the shaft with tool

T69P-2B384-A Detail 2 and TOOL

1225-DA.

INSTALLATION

1.
Press a new rotor onto the axle

shaft. Install a new sensor assembly

on the shaft with tool T69P-

2B384-ADetail 1 and TOOL 1225-

DA, and press the bearing and bear-

ing retainer onto the shaft (Refer to

Part 4-2).

2.
Insert the axle shaft assembly in

the rear axle housing onto the four

backing plate retaining bolts, feeding

the sensor lead through the hole in the

backing plate.

3.
Seat the sensor lead grommet in

the backing plate.

4.
Install the four nuts on the re-

taining bolts and tighten to specifica-

tions.

5.
Connect the sensor lead to the

rear wiring harness and install two re-

taining straps.

6. Install the rear brake drum and

retain with the Tinnerrhan drum re-

taining nuts.

7.
Install the rear wheel and tire as-

sembly and tighten the wheel nuts to

specifications.

8. Test the vehicle on the hoist to

verify proper operation of the skid

control system.procarmanuals.com

02-02-41
Brake System

02-02-41

bolt and G-ring in the bottom of the

master cylinder.

8. Install the bleed screw (if so

equipped). Install the gasket (dia-

phragm) in the master cylinder filler

cover. Position the gasket as shown in

Figs.
40 and 41. Make sure the gasket

is securely seated.

9. Install the cover and gasket on

the master cylinder and secure the

cover into position with the retainer.

DISC BRAKE CALIPER

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Disassembly

1.
Remove the caliper assembly

from the vehicle as outlined in Section

2.

2.
Remove the caliper locating pins

from the caliper assembly and lift the

anchor plate from the caliper.

3.
Slide the two outer shoe retain-

ing clips off the retaining pins (Fig.

43).

4.
Remove the two retaining pins,

then remove the outer brake shoe

from the caliper.

5.
Slide the inner brake shoe out-

ward until it is free of the hold-down

springs, then remove the brake shoe.

6. Apply air pressure to the fluid

port in the caliper with a rubber

tipped nozzle (Tool 7000-DD) as

shown in Fig. 44 to remove the piston.

Place a cloth over the piston before

applying air pressure to prevent dam-

age to the piston. If the piston is

seized and cannot be forced from the

FIBER

BLOCK

CALIPER

PISTON

H 1574-B

FIG. 44 —Removing Piston From

Caliper —
All
Models Except

Lincoln Continental
caliper, tap lightly around the piston

while applying air pressure. Care

should be taken because the piston

can develop considerable force due to

pressure build-up.

7.
Remove the dust boot from the

caliper assembly.

8. Remove the rubber piston seal

from the cylinder and discard it.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent. Use

clean, dry, compressed air to clean out

and dry the grooves and passage ways.

Be sure that the caliper bore and com-

ponent parts are completely free of

any foreign material.

Check the cylinder bore and piston

for damage or excessive wear. Replace

the piston if it is pitted, scored, or the

chrome plating is worn off.

Assembly

1.
Apply a film of clean brake fluid

to the new caliper piston seal and in-

stall it in the cylinder bore. Be sure

the seal does not become twisted and

that it is seated fully in the groove.

2.
Install a new dust boot by setting

the flange squarely in the outer groove

of the caliper bore.

3.
Coat the piston with the speci-

fied fluid and install the piston in the

cylinder bore. Spread the dust boot

over the piston as it is installed. Seat

the dust boot in the piston groove.

4.
Position the inner brake shoe so

that the ears of the shoe rests on the

top of the anchor plate bosses and be-

neath the hold-down springs.

5.
Install new caliper locating pin

insulators in the anchor plate.

6. Position the caliper on the an-

chor plate.

7.
Apply water or isopropyl alcohol

to the caliper locating pins and install

them loosely in the anchor plate. Be

sure the guide pins are free of oil,

grease or dirt.

8. Install the caliper on the spindle

as outlined under Disc Brake Caliper

Assembly.

LINCOLN CONTINENTAL

Disassembly

Do not remove the bridge bolts that

hold the two halves of the caliper to-

gether. The two caliper housings are

shown separated in Fig. 46 for illus-

tration purposes only.
1.
Remove the caliper assembly

from the car as outlined in Section 2.

2.
Remove the two attaching bolts

and the caliper splash shield (Fig. 46).

3.
Remove the two shoe and lining

assemblies.

4.
Remove the flexible brake hose

from the caliper.

5.
Remove the external transfer

tube.

6. Remove the four dust boots from

the caliper housings and piston

grooves.

7.
Clamp the caliper in a vise and

secure it by the mounting flanges on

the inboard housing (Fig. 45).

8. Remove the four pistons from

the cylinder bores with the special tool

shown in Fig. 45. To prevent cocking

with consequent damage to the piston

or bore, rotate the piston with the tool

while pulling it outward at the same

time.
Be careful to avoid scratching or

damaging the outside diameter surface

or dust boot retaining groove of the

piston. Such damage causes poor seal-

ing.

If a piston is so completely seized in

the cylinder bore that it can not be re-

moved with the special tool, the cali-

per housing must be replaced, by posi-

tioning two screwdrivers in the piston

dust boot retaining groove and prying

outward. To prevent cocking, tap the

end of the piston lightly around the

circumference with a hammer, while

the prying force is being applied. Be

careful to avoid damaging the dust

boot retainer in the caliper housing

(Fig. 46). If this method of removal is

used, the pistons must be replaced.

If the caliper dust boot retainer or

retaining groove is damaged or

scratched, pry the retainer out of the

caliper housing with screwdrivers.

Too/-T65P-2
J
18- A

H 1652-A

FIG. 45—Removing or Installing

Pistons —
Lincoln
Continentalprocarmanuals.com

03-01-11
Suspension — Steering, Wheels And Tires — General Service

03-01-11

3.
Inspect the rotor, rollers, cam

ring, pressure plate, cover, and bush-

ing in the pressure plate for wear or

scoring. If damaged, replacement of

the pump (less housing) is required.

4.
Make sure the inner faces of the

cover and the housing are free of

paint, nicks, or burrs. Check all fluid

passages for restrictions.

5.
Inspect the valving surfaces

(areas where the rotor and rollers con-

tact) for wear or scoring. Replace the

pressure plate or the cover if worn or

scored. Inspect the bushing in the

pressure plate for wear or scoring, and

replace the plate if necessary.

6. Inspect the control valve for

scores, nicks, or burred edges. Re-

place the valve if damaged. Do not dis-

assemble the valve. Check the valve

for free movement in the housing

bore.

7.
Inspect the tube seat in the hous-

ing. If damaged, remove it with an

E-Z-Out and install a new seat.

SHOCK ABSORBER CHECKS

All vehicles are equipped with hy-

draulic shock absorbers of the direct-

acting type and are nonadjustable and

nonrefillable. They cannot be repaired.
Before replacing a shock absorber,

check the action of the shock absor-

bers as follows:

ON VEHICLE TESTS

1.
Check the shock absorber to be

sure it is securely and properly in-

stalled. Check the shock absorber in-

sulators for damage and wear.

Replace any defective insulators and

tighten attachments to the specified

torque (on a shock absorber which in-

corporates integral insulators, replace

the shock absorbers).

2.
Inspect the shock absorber for

evidence of fluid leakage. A light film

of fluid is permissible. Be sure any

fluid observed is not from sources

other than the shock absorber.

Replace the shock absorber if leak-

age is severe.

3.
Disconnect the lower end of the

shock absorber. Extend and compress

the shock absorber as fast as possible,

using as much travel as possible.

Action should become smooth and

uniform throughout each stroke.

Higher resistance on extension than

on compression is a normal condition.

Faint swish noises are also normal.

Remove the shock absorber for a

bench test if action is erratic. If the
action is smooth, but the shock absor-

bers are suspected of being weak fol-

low step 4:

4.
Repeat step 3 on the mating

shock absorber installed on the oppo-

site side of the vehicle, and compare

results of both tests. If the action is

similar, it is unlikely that either shock

absorber is defective. Reconnect both

shock absorbers.

Replace the shock absorber having

the lower resistance. Ensure that the

part number of the replacement is the

same as that of the original shock ab-

sorber. The replacement shock absor-

ber resistance will appear to be higher

than either original due to initial fric-

tion of the rod seal.

BENCH TEST

With the shock absorber right side

up (as installed in vehicle), extend it

fully. Then turn the shock absorber

upside down and fully compress it.

Repeat this procedure at least three

times to ensure that any entrapped air

has been expelled. Now place the

shock absorber right side up in a vise,

and hand stroke the shock absorber as

described in On Vehicle Tests, step 3.

If action is not now smooth and uni-

form, install a new shock absorber.procarmanuals.com

03-02-10
Suspension

03-02-10

lower
arm
free
to
drop
as
coil spring

tension
is
eased.
If a
chain hoist
or a

jack that
has
a
narrow contact
pad is

to
be
used
on the
bumper
to
raise
the

car, distribute
the
load along
the

bumper
by
using
a
steel plate
3 or 4

inches long
as a
contact
pad to pre-

vent damaging
the
bumper.

2.
If the
ball joint
is
riveted
to the

arm, drill
a
1/8-inch
pilot hole
com-

pletely through each rivet. Then drill

off
the
rivet head through
the
pilot

hole with
a
3/8-inch drill,
and
drive

out both rivets.

3.
Position
a
jack
or
safety stand

under
the
lower
arm, and
lower
the

vehicle about
6
inches
to
offset
the

coil spring tension.

4.
Remove
the
cotter
pin
from
the

ball joint stud,
and
remove
the nut.

5.
Place
a box
wrench over
the

lower
end
of the
tool shown
in
Fig.
7,

and position
the
tool.
The
tool should

seat firmly against
the end of
both

studs,
and
not
against
the
upper stud

nut.

6. Turn
the
wrench until both studs

are under tension,
and
then, with
a

hammer,
tap the
spindle near
the

lower stud
to
loosen
the
stud from
the

spindle.
Do not
loosen
the
stud with

tool pressure alone. Remove
the
ball

joint.

7.
Clean
the end of the arm, and

remove
all
burrs from
the
hole edges.

Check
for
cracks
in the
metal
at the

holes,
and
replace
the arm if it is

cracked.

8. Position
the
stud
of
the
ball joint

to
the
spindle bore,
and
install
the at-

taching
nut
finger-tight.

9. Attach
the
ball joint
to
the
lower

arm.
Use
only
the
specified bolts
and

nuts.
Do not
rivet
the new
ball joint
to

the
arm.
Torque nuts
to
specification.

10.
Torque
the
ball joint stud
nut

to specification,
and
install
a
new cot-

ter
pin.

11.
Remove
the
jack.

12.
Check
and, if
necessary, adjust

caster, camber,
and
toe-in. Whenever

any part
of the
front suspension
has

been removed
and
installed, front

wheel alignment must
be
checked.

BALL JOINT REPLACEMENT

LINCOLN CONTINENTAL

The lower ball joint
is
riveted
to
the

lower
arm
wheras
the
upper ball joint

is bolted
to the
upper
arm.
When
re-

placing
a
ball joint,
use all the
parts

supplied
in the kit.
T57P-3006-A
UPPER
ARM

UPPER BALL JOINT

LOWER BALL JOINT
\
LOWER
ARM

T62F.3006-A
F
1493-A

FIG. 13— Loosening Ball Joint

Stud

Lower
Arm

1.
Raise
the
vehicle. Place
a sup-

port under each rail
to the
rear
of
the

lower
arm in the
lifting
pad
area.

2.
Remove
the
wheel
and
tire from

the
hub.

3.
Remove
2
bolts
and
washers that

attach
the
caliper
to the
spindle.
Re-

move
the
caliper from
the
rotor
and

wire
it to the
underbody
to
prevent

damage
to the
brake hose.

4.
Remove
the hub and
rotor from

the spindle.

5.
Remove
the
splash shield
and

gasket from
the
spindle.

6. Remove
the
cotter
pin
from
the

lower ball stud,
and
loosen
the nut

one
to two
turns.

7.
Place
a box
wrench over
the

lower
end of the
ball joint remover

tool,
and
position
the
tool
as in Fig.

13.
The
tool should seat firmly against

the ends
of
both studs,
and not

against
the
lower stud
nut.

8. Turn
the
wrench until both studs

are under tension,
and
then, with
a

hammer,
tap the
spindle near
the

lower stud
to
loosen
the
stud from
the

spindle.
Do not
loosen
the
stud with

tool pressure alone.

9. Place
a
jack under
the
spring

pocket
in the
lower
arm, and
raise
the
arm slightly. Place
a
support stand

under
the
lower
arm as a
safety
pre-

caution.

10.
Remove
the nut
from
the
ball

joint stud. Raise
the
upper
arm and

spindle until
the
spindle clears
the
ball

stud. Prop
the
upper
arm in a
raised

position.

11.
Remove
the
ball -joint rivet

heads with
a
chisel. Punch
the
remain-

ing portion
of the
rivets from
the

holes,
and
remove
the
joint.

12.
Install
the
new
joint using
the

parts supplied
in the kit.
Torque
the

nuts
to
specification. Make sure
the

joint
is
completely filled with
the
spec-

ified lubricant.

13.
Lower
the
upper
arm
while

guiding
the
spindle over
the
ball stud.

Install
the
stud
nut and
tighten
it to

specification. Continue
to
tighten
the

nut
to
line
up the
cotter
pin
hole.
In-

stall
the
cotter
pin.

14.
Install
the
gasket
and
shield
on

the spindle. Tighten
the
attaching

bolts
to
specifications.

15.
Install
the
hub and
rotor
on the

spindle
and
adjust
the
wheel bearings.

16.
Install
the
caliper
to
the
spindle

and tighten
the
attaching bolts
to

specifications. Check
for the
correct

flexible hose routing (Part
2-2).

17.
Install
the
wheel
and
tire.
Tor-

que
the
wheel nuts
to
specification
and

lower
the
vehicle.

Upper
Arm

1.
Place
a
jack under
the
outer
end

of
the
lower
arm,
and
raise
the arm.

Place
a
support stand under
the
side

rail
in the
lifting
pad
area.

2.
Remove
the
wheel
and
tire.

3.
Remove
the
cotter
pin
from
the

upper ball stud,
and
loosen
the nut

one
to two
turns.

%
4.
Place
a box
wrench over
the

lower
end of the
ball joint remover

tool,
and
position
the
tool
as in Fig.

13).
The
tool should seat firmly

against
the
ends
of
both studs,
and

not against
the
upper stud
nut.

5.
Turn
the
wrench until both studs

are under tension,
and
then, with
a

hammer,
tap the
spindle near
the

upper stud
to
loosen
the
stud from
the

spindle.
Do not
loosen
the
stud with

tool pressure alone.

6. Raise
the
upper
arm to
free
the

ball stud from
the
spindle. Wire
the

upper
end
of
the
spindle
to the
under-

body
to
prevent damage
to the
brake

hose.

7.
Remove
the
ball joint retaining

nuts
and
bolts,
and
remove
the
joint.

8. Install
the new
joint using
the

parts supplied
in the kit.
Torque
theprocarmanuals.com

03-02-18
Suspension

03-02-18

5.
Remove the cotter pin from the

upper ball joint stud nut.

6. Loosen the upper ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

7.
Install tool T57P-3006-A be-

tween the upper and lower ball joint

studs with the adapter screw on top

(Fig. 13). The tool should be seated

firmly against the ends of both studs

and not against the nuts or lower stud

cotter pin.

8. With a wrench, turn the adapter

screw until the tool places the stua

under tension. Tap the spindle near

the upper stud with a hammer to loos-

en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

9. Remove the tool from between

the ball joint studs and place a floor

jack under the lower arm.

10.
Raise the floor jack to relieve

the pressure from the upper ball joint

stud nut and remove the nut.

11.
Remove the upper arm inner

shaft attaching bolts. Remove the

upper arm and inner shaft as an as-

sembly (Fig. 1).

12.
Remove the bumpei from the

upper arm.

Installation

1.
Position the bumper to the upper

arm and install the nut and washer.

Torque the nut to specifications.

2.
Position the upper arm inner

shaft to the frame side rail and install

the 2 attaching bolts and washers

snug.

3.
Connect the upper ball joint stud

to the spindle and install the attaching

nut. Torque the nut to specification

and continue to tighten the nut until

the cotter pin hole in the stud is in

line with the nut slots. Then, install

the cotter pin.

4.
If equipped with drum type bra-

kes—Adjust the brakes as outlined in

Part 2-2. Install the wheel, tire, and

drum to the spindle and adjust the

wheel bearings as outlined in Part

3-12.

5.
If equipped with disc brak-

es—Install the wheel and tire on the

hub and adjust the wheel bearings as

outlined in Part 3-12.

6. Install the hub cap or wheel

cover.

7.
Remove the safety stands and

lower the front of the vehicle.

8. Check caster, camber, and toe-in

and adjust as required (Section 2, Part

3-D.
COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the front of the vehicle,

position safety stands under the

frame, and lower the vehicle slightly.

2.
Remove the wheel and tire.

3.
Remove the shock absorber

lower attaching nuts and washers.

4.
Remove the shock absorber

upper mounting bracket attaching

nuts,
and remove the shock absorber

and bracket as an assembly (Fig. 26).

On all 8-cylinder vehicles, remove

the air cleaner to obtain access for

tool installation.

5.
Install the spring compressor

tool and compress the spring (Figs.

19,
20 and 21).

6. Position a safety stand under the

lower arm.

7.
Remove the cotter pin from the

nut on the upper ball joint stud, and

loosen the nut one or two turns. Do

not remove the nut from the stud at

this time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs as shown in Fig. 10. The

tool should seat firmly against the

ends of both studs and not against the

stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension; then, hit the spindle

smartly near the upper stud with a

hammer to break the stud loose in the

spindle. Do not loosen the stud in the

spindle with tool pressure only. If

both arms are being removed, loosen

the lower stud in the same manner as

the upper stud.

10.
Remove the nut from the upper

stud and lift the stud out of the

spindle.

11.
Remove the upper arm inner

shaft attaching nuts from the engine

compartment, and remove the upper

arm.

12.
Wipe off all loose dirt from the

upper arm parts. Do not wash the ball

joint with a solvent.

Installation

1.
Position the upper arm on the

underbody mounting bracket, and in-

stall the nuts and lock washers on the

two inner shaft attaching bolts. The

specified keystone-type lock washers

must be used. Torque the nuts to

soecification.
2.
Position the upper ball joint stud

in the top of the wheel spindle, and in-

stall the stud nut. Torque the nut to

specification, and continue to tighten

it until the cotter pin hole and slots

line up. Install a new cotter pin.

3.
Release the coil spring, remove

the tool, and install the front shock

absorber and the wheel and tire.

LINCOLN CONTINENTAL

Removal

1.
Place a jack under the outer end

of the suspension lower arm and raise

the arm. Refer to Fig. 22.

2.
Remove the wheel and tire.

3.
Remove the cotter pin from the

upper ball joint stud. Loosen the nut

one or two turns.

4.
Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the upper stud nut.

5.
Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the upper

stud to loosen it from the spindle. Do

not loosen the stud with tool pressure

alone. Remove the nut.

UPPER MOUNTING BRACKET

LOWER RETAINING BOLTS F 1490-A

FIG. 26—Removing or Installing

Front Shock Absorber—Typicalprocarmanuals.com

03-02-26
Suspension

03-02-26

T64K-578 7-B2 (Adapter)

-83 (Nut)

(Bolt)

SPRING FRONT
EYE

Tool-T64K-5781-B2 (Adapter)
BUSHING

F 1484-A

FIG. 35—Rear Spring Front Bushing Installation—Typical

5.
Remove
the
rear shackle assem-

bly
and the two
outer bushings.

6. Remove
the
front hanger bolt,

nut,
and
washer from
the eye at the

forward
end of the
spring. Lift
out the

spring assembly.

7.
If the
front bushing
is
being
re-

placed, assemble
the
special tool
com-

bination
to the
bushing
in the
spring

front
eye as
shown
in
Fig.
34.

8. While holding
the
tool
nut,
tight-

en
the
tool bolt against
the
tool thrust

washer,
the
adapter,
and
detail
Al.

This operation will force
the
bushing

out
of the
spring
eye
into detail
A4 of

the tool
as
shown.

Installation

During rear suspension leaf spring

assembly replacement
in
service,
all

used attaching components must
be

discarded
and
replaced with
new com-

ponents.

1.
Assemble
the
bushing
and the

special tool combination
to the
spring

front
eye as
shown
in Fig. 35.

2.
While holding
the
tool
nut,
tight-

en
the
tool bolt against
the
tool thrust

washer, adapter,
and
detail
A4 to

force
the
bushing into
the
spring
eye

as shown.

3.
Position
the
spring under
the

rear axle
and
insert
the
shackle
as-

sembly into
the
rear hanger bracket

and
the
rear
eye of the
spring.
4.
Install
the
shackle inner bush-

ings,
the
shackle plate,
and the
lock-

nuts.
Tighten
the
locknuts finger-tight.

5.
Position
the
spring front
eye in

the front hanger, slip
the
washer
on

the front hanger bolt,
and
(from
the

inboard side) insert
the
bolt through

the hanger
and
eye. Install
the
locknut

on
the
hanger bolt
and
tighten finger-

tight.

6. Lower
the
rear axle until
it
rests

on
the
spring. Position
the
spring clip

plate
on the
clips (U-bolts). Install
the

U-bolt nuts
and
torque
to
specifica-

tion.

7.
Connect
the
lower
end of the

shock absorber
to the
spring clip plate

using
a new nut if
working
on a sta-

tion wagon
or
Ranchero.

8. Place safety stands under
the

rear axle, lower
the
vehicle until
the

spring
is in the
approximate curb load

position,
and
then torque
the
front

hanger stud locknut
to
specification.

9. Torque
the
rear shackle locknuts

to specification.

10.
Remove
the
safety stands
and

lower
the
vehicle.

REAR SPRING

LINCOLN CONTINENTAL

Removal

1.
Raise
the
vehicle
and
place
sup-

port stands under
the
sidemembers
on
the rear
of
each rear spring hanger.

2.
Lower
the
rear axle slightly
to

reduce some
of the
spring load; then,

remove
the
spring U-bolts.

3.
Remove
the
nuts, lock washers

and front mounting stud. Refer
to

Fig.
6.

4.
Remove
the
rear shackle nuts

and mounting plate. Remove
the

lower inner insulator. Remove
the

spring.
If the
rear shackle insulators

are
to be
replaced,
it
will
be
necessary

to remove
the
rear hanger assembly.

(Hanger attaching bolts must
be tor-

qued
to
specification when rein-

stalled.)

5.
Remove
the
insulators from
the

spring.

6. Examine
all
parts
for
wear
or

damage. Note
the
condition
of the

spring center bolt.

7.
The
spring center bolt
can be re-

placed
by
clamping
the
spring
in a

vise,
thus keeping
the
spring
com-

pressed during bolt removal
and in-

stallation.

Installation

1.
Attach
the
spring
and
bushing
to

the front hanger. Torque
the
outboard

nut
to
specifications.
Do not
tighten

the inboard
nut at
this time.

2.
Install
the
spring
to the
rear

shackle assembly with
the
insulators

in position.
Do not
tighten
the
nuts
at

this time. Refer
to Fig. 6.

3.
Place
the
insulator
and
retainers

in position
on the
spring.

4.
Lower
the
axle housing onto
the

insulator
and
retainer assembly.

If
a
wedge
was
located between
the

upper retainer
and
mounting
pad,

reinstall
the
same thickness wedge

with
the
taper
in the
original direc-

tion. Raise
the
axle until
the
spring
is

approximately horizontal with
the

floor.

5.
Install
the
lower insulator retain-

er
and
U-bolts.
Do not
tighten
the U-

bolt nuts
at
this time. Torque
the
rear

shackle nuts
to
specifications.

6. Torque
the
inboard
nut at the

front
eye to
specification.

7.
Tighten
the
U-bolt nuts evenly
to

the specified torque.

8. Make sure
the
lower insulator

retainer contacts
the
upper retainer.procarmanuals.com

03-04-03
Automatic Air Leveling System — Lincoln Continental

03-04-03

outlet lines to their respective parts.

3.
Adjust the trim height as de-

tailed in Section 4.

4.
Connect the link to the arm.

5.
Remove the jack stands and

lower the vehicle.

SUPER LIFT SHOCK ABSORBER

REMOVAL

1.
Raise the vehicle and place jack

stands under the axle to compress the

super lift.

2.
Loosen the air line or lines (right

super lift) slowly to release the air
from the system. Then, disconnect the

line or lines.

3.
Remove the three mounting plate

attaching screws from the upper end

of the super lift.

4.
Remove the attaching nut and

washer from the lower end of the

super lift and remove it from the vehi-

cle.

5.
Remove the nut, outer washer

and the insulator that attach the super

lift to the mounting plate. Remove the

plate, remaining insulator and washer.

INSTALLATION

1.
Position a washer, insulator,

mounting plate, insulator, washer and
nut on the stud at the upper end of

the super lift. Torque the nut to speci-

fication.

2.
Install the mounting plate, outer

insulator, washer and nut on the stud.

Torque the nut to specification.

3.
Attach the mounting plate and

shock absorber to the crossmember

with the attaching screws to specifica-

tions.

4.
Connect the lower end of the

super lift to the mounting stud with

the washers and attaching nut. Torque

the nut to specification.

5.
Connect the air line or lines

(right super lift) to the super lift.

6. Start the engine and check for

leaks.

3 IN-VEHICLE ADJUSTMENTS AND REPAIRS

REGULATOR ADJUSTMENT HEIGHT CONTROL VALVE

The regulator may be adjusted if

the regulator pressure is under 100 psi

with the reservoir pressure at a mini-

mum of 140 psi. If the regulated pres-

sure exceeds 130 psi, the regulator

must be replaced.

To adjust the regulator, remove the

boot and reposition the sleeve and re-

tainer deeper into the body of the re-

gulator, using a deep well socket (Fig.

4).
If the regulator pressure remains

under 100 psi, replace regulator.
SILICONE FLUID

REPLACEMENT

If the height control valve time

delay does not fall within specifica-

tion, the silicone fluid must be re-

placed. Then repeat the time delay

test. If delay is still not within specifi-

cations, replace the height control

valve.

1.
Remove control valve and clean
the exterior of the valve thoroughly.

2.
Position the valve with delay

plug on top. Remove delay plug and

drain silicone fluid from the chamber.

Remove the O-ring from the chamber

(Fig. 5), and discard the O-ring.

3.
Remove the cover plate retaining

ring, using snap ring pliers. Remove

the delay cover from the valve body.

Remove the O-ring from the chamber,

and discard the O-ring.

4.
Place a new O-ring over the

delay plug and install the plug. Tor-

que the plug to 20-30 in-lbs. .

5.
Pour silicone fluid into the delay

piston chamber until fluid level is 5/16

inch below the top edge of the body.

Add or remove fluid with an eye drop-

per until the proper fluid level is

reached.

6. Hold the control valve body in a

vise with the delay chamber elevated

slightly. Carefully operate the lever to

purge trapped air from the fluid.

7.
Place a new O-ring in the groove

around the delay piston bore. Install

5/16" TO

FLUID LEVEL

F 1405 A

FIG. 4—Adjusting Regulator
F1406 A

FIG. 5—Replacing Silicone Fluidprocarmanuals.com