1969 FORD MUSTANG torque

04-04-03
Rear Axle
—
Ford Light-Duty (WER)

04-04-03

LOCK BOLT

DIFFERENTIAL PINION SHAFT
E 1596- A

FIG.
2—Differential pinion shaft

and Lock Bolt

AXLE SHAFT

LOCK

E 1597-A

FIG. 3—Removal
and
Installation

of C-Locks
and
Axle Shaft

Carefully remove
any
burrs
or
rough

spots.
Replace worn
or
damaged

parts.
A
brownish yellow color
on the

bearing journal
of the
shaft
is
normal

and
the
shaft need
not be
replaced.

Slight pitting
and
wear
is
also normal.

INSTALLATION

1.
Lightly coat
the
wheel bearing

rollers with axle lubricant. Install
the

bearings
in the
axle housing with
the

tool shown
in Fig. 5. The
bearing

should seat firmly against
the
shoul-

der.

2.
Wipe
all
lubricant from
the oil

seal bore before installing
the
seal.

3.
Inspect
the
original seal
for

nicks,
scuffs
or
abnormal wear,
and

replace
it if
necessary.
The new
seals

are pre-packed with lubricant
and do

not require
an oil
soak before installa-

tion.

4.
Install
the oil
seal with
the
tool

shown
in Fig. 6.
Installation without

the
use of the
proper tool will distort

the seal
and
cause leakage.

5. Replace
the
O-ring
in the
C-lock

groove
on the
axle shaft.

6. Slide
the
axle shaft(s) into place
Tool
-
T66L-12132

Tool
-
7507- 700-A

\

1

T50T-100-A
BEARING

Tool - 766L-72J32-8

(THREAD
REDUCING

ADAPTER PART ONLY)

SEAL

FIG. 4—Removal
of
Axle Seal
or

in
the
axle housing. Exercise care that

splines
or any
portion
of the
axle

shaft(s)
do not
damage
the oil
seal(s)

and that they engage with
the
splines

of
the
differential side gear(s).

7. Install
the
axle shaft C-lock(s)

on
the
inner
end of the
shaft(s)
(Fig.

3)
and
push
the
shaft(s) outward
so

that
the
shaft locks seat
in the
conter-

bore(s)
of the
differential side gear(s).

8. Position
the
differential pinion

gears
and
thrust washers
180
degrees

apart
to the
differential side gears.

Revolve
the
gear assembly until
the

holes
in the
differential case
are a-

ligned with the pinion gears.

9. Position
the
differential pinion

shaft through
the
case
and
pinions,
a-

ligning
the
hole
in the
shaft with
the

lock bolt hole. Install
the
lock bolt

Tool
-
760K-7697.fi
E 1598.A

Axle Bearing

and torque
it to
specification.

10.
Install
the
brake drum
and

tighten
the
attaching (Tinnerman)

nuts.

11.
Install
the
wheel
and
tire
on the

brake drum.

12.
Clean
the
gasket mounting
sur-

faces
of the
rear axle differential

housing
and the
cover. Install
a new

cover gasket, cover
and the
attaching

bolts.
Torque
the
bolts
to
specifica-

tion.

13.
Raise
the
rear axle. Make sure

the rear axle
is in
running position.

Add
the
amount
of
specified lubricant

required
to
reach
to the
bottom
of the

filler plug hole. Install
the
filler plug

and torque
it to
specification.

14.
Remove
the
safety support

stands
and
lower
the
vehicle.

7oo/

765F-7 777-A

E 1571-A

FIG. 5—Installation
of
Axle

Shaft Bearing
FIG.
6—Rear
Axle Shaft Bearing

Seal Installationprocarmanuals.com

04-04-04
Rear Axle — Ford Light-Duty (WER)

04-04-04

REMOVAL AND INSTALLATION

AXLE HOUSING

Refer to Fig. 7.

REMOVAL

1.
Raise the vehicle on a hoist.

2.
Remove the wheels and tires

from the brake drums.

3.
Position a drain pan and loosen

the rear axle cover to housing attach-

ing bolts. Drain the housing.

4.
Remove the attaching (Tinner-

man) nuts that secure the brake drums

to the axle shaft flanges, and then re-

move the drums (Fig. 7).

5.
Remove the axle housing cover

bolts,
cover and gasket. Discard the

gasket. Remove the drain pan.

6. Disconnect the drive shaft at the

drive pinion companion flange. Re-

move the drive shaft from the trans-

mission extension housing. Install an

oil seal replacer tool in the transmis-

sion housing to prevent leakage. Refer

to the transmission group for the ap-

propriate tool.

7.
Disconnect the lower end of the

shock absorbers at the mounting

brackets.

8. Disconnect the track bar from

the axle housing stud. If the axle

housing is to be replaced, transfer the

stud to the new housing.

9. Position safety stands under the

rear frame members. Lower the vehi-

cle with the hoist and allow the axle

to lower far enough to relieve rear

spring tension.

10.
Remove the pinion shaft lock

bolt and pinion shaft (Fig. 2), differ-

ential pinion gears and thrust washers.

11.
Push the axle shaft(s) inward

toward the center of the axle housing.

Remove the C-locks from the inner

ends of the axles (Fig. 3). Remove the

axle shafts from the housing. Extreme

care must be used to avoid contacting

the axle shaft seal lip with any portion

of the axle shaft other than the seal

journal.

12.
Disconnect the vent hose from

the rear vent tube and remove all

brake lines from the axle housing re-

taining clips.

13.
Remove the brake backing

plate attaching nuts and the plates

from the axle housing. Suspend the

plates above the axle housing with

mechanics wire. The hydraulic brake

lines and the parking brake cables will

remain attached to the brake backing

plates.
14.
Support the rear axle housine

on a jack.

15.
Remove the right and left rear

springs and insulators.

16.
Remove the nuts, washers and

pivot bolts that connect the suspension

lower arms to the axle housing. Dis-

connect both arms from the axle

housing.

17.
Disconnect the upper suspen-

sion arm from the axle housing by re-

moving the pivot bolt, nut, lock wash-

er and two eccentric washers.

18.
Lower the rear axle to the floor

with the jack and remove the axle

from under the vehicle.

19.
Remove the wheel bearings and

oil seals with the tool shown in Fig. 4.

20.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. Refer

to Section 4, Major Repair Operation

for the procedure.

INSTALLATION

1.
Lightly coat the wheel bearing

rollers with axle lubricant. Install

wheel bearings in the axle housing

with the tool shown in Fig. 5. The

bearings should seat firmly against the

shoulder.

2.
Wipe all lubricant from the oil

seal bore before installing the seal. If

axle housing is being replaced, new

seals must be installed.

3.
Inspect the original seal for

nicks,
scuffs or abnormal wear, and

replace if necessary. New seals are

pre-packed with lubricant and do not

require an oil soak.

4.
Install the seal with the tool

shown in Fig. 6. Installation without

the use of the proper tool will distort

the seal and cause leakage.

5. Raise the rear axle into position

under the vehicle with a hoist or floor

jack. Connect the suspension lower

arms to their mounting brackets on

the axle housing with pivot bolts and

nuts.
Do not tighten the mounting

bolts at this point.

6. Position the suspension upper

arm in its mounting bracket on the

axle housing and install the adjusting

bolt, eccentric washers, lock washer

and nut. Do not tighten the mounting

bolt at this point.

7.
Place the rear coil springs and

insulators into position in the pockets

provided.
8. Place the brake backing plates

on the axle housing flanges, install 4

attaching bolts and nuts and torque

them to specifications.

9. Position the brake lines to the

axle housing and secure them with the

retaining clips. If the axle housing is

new, install a new vent. When install-

ing the new axle vent apply a small

amount of Locktite (C5AZ-19554-B)

to prevent oil leakage between vent

and axle housing. Connect the vent

tube to the vent.

10.
Install the pinion side gears and

thrust washer.

11.
Slide the axle shafts into place

in the axle housing. Exercise care that

splines or any portion of the axle

shafts do not damage the oil seals and

that they engage with the splines of

the differential side gears.

12.
Install the axle shaft C-lock O-

ring and C-lock on the inner end of

the shaft and push the shaft outward

so that the shaft lock seats in the

counterbore of the differential side

gear.

13.
Position the pinion differential

gears and thrust washers 180 degrees

apart to the differential side gears.

Revolve the gear assembly until the

holes in the differential case are al-

igned with the pinion gears.

14.
Position the differential pinion

shaft through the case and pinions, al-

igning the hole in the shaft with the

lock bolt hole. Install the lock bolt

and tighten it to specification.

15.
Clean the gasket mounting sur-

face of the rear axle housing and the

cover. Install a new cover gasket,

cover and the attaching bolts. Torque

the bolts to specification.

16.
Raise the rear axle on a hoist

and remove the safety stands.

17.
Connect the track bar to the

mounting stud. Install the washer and

nut. Torque the nut to specification.

18.
Connect the two rear shock ab-

sorbers to the mounting brackets on

the axle housing and torque the at-

taching nuts to specification.

19.
Make sure that both the front

and rear pivot bolts of the upper and

the two lower arms are loose, then

raise the axle assembly to the con-

trolled height (Fig. 8). Hold the axle

at the controlled height by placing

blocks or pieces of steel pipe between

the axle housing and the bumper rear

screw on the side rail.procarmanuals.com

04-04-06
Rear Axle — Ford Light-Duty (WER)

04-04-06

20.
With the axle at controlled

height, torque the suspension upper

and lower arm front pivot bolts and

nuts to specifications. Torque the

lower arm to axle housing pivot bolts

and nuts to specifications.

21.
Remove the oil seal replacer

from the transmission extension hous-

ing. Install the drive shaft in the ex-

tension housing. Align the scribe

marks on the cups, flange and drive

shaft and connect the drive shaft at

the drive pinion flange. Torque the at-

taching bolts to specification
FRAME

TIGHTEN ARM

ATTACHING BOLTS

AT 5-45/64 INCH

HEIGHT POSITION
5-45/64 INCH

HEIGHT FOR

INSTALLATION

OF ARMS

E 1600-B

FIG.8—
Axle
Normal Curb Height

and Controlled Height for Arm

Installation
22.
Install the brake drum and at-

taching (Tinnerman) nuts.

23.
Install the wheel and tire on the

brake drum. Install the wheel covers.

24.
Adjust the drive shaft and pin-

ion angle to specification.

25.
Add the amount of specified lu-

bricant required to reach to the bot-

tom of the filler plug hole. Make sure

the rear axle is in running position.

Install the filler plug and torque it to

specification.

26.
Lower the vehicle.

4 MAJOR REPAIR OPERATIONS

DISASSEMBLY OF AXLE
The rear axle components are

shown in Fig. 9.

DIFFERENTIAL SIDE GEAR

AXLE SHAFT C-WASHER \

DIFFERENTIAL PINION SHAFT

THRUST WASHER

BEARING ASSEMBLY

CUP
THRUST WASHER

^^ DIFFERENTIAL PINION GEAR

BEARING ADJUSTING NUT

DIFFERENTIAL

PINION SHAFT

LOCK BOLT

LOCK WASHER
BOLT

LOCK WASHER

ADJUSTING NUT LOCK

DRIVE GEAR ATTACHING BOLT

BEARING CAP

AXLE HOUSING ASSEMBLY

PINION AND RING GEAR

PINION LOCATING SHIM(S)

BEARING CUP

BOLT

NUT

BEARING CUP

COLLAPSIBLE SPACER

AXLE SHAFT

E 1572-C

FIG. 9—Disassembled Light-Duty (WER) Rear Axleprocarmanuals.com

04-04-09
Rear Axle — Ford Light-Duty (WER)
04-04-09

case several revolutions in each direc-

tion while the bearings are loaded to

seat the bearings in their cups. This

step is important.

5. Again loosen the right nut to re-

lease the preload. Check to see that

the left nut contacts the bearing cup.

Using the dial indicator set-up shown

in Fig. 13, Part 4-1, adjust the preload

to 0.008 to 0.012 case spread for new

bearings or 0.005 to 0.008 for the

original bearings, if re-used.

6. Check the runout of the differen-

tial case flange with a dial indicator.

If the runout does not now exceed

specifications, install a new ring gear,

if the runout still exceeds specifica-

tions,
the ring gear is true and the

trouble is due to either a defective

casting or worn bearings.

7.
Remove the differential case

from the carrier and remove the side

bearings from the case.

8. Install new bearings on the case

hubs,
and again install the differential

assembly in the carrier without the

ring gear.

9. Check the case runout again with

the new bearings. If the runout is now

within limits, the old bearings were

excessively worn. Use the new bear-

ings for assembly. If the runout is still

excessive, the case is defective and

should be replaced.

ASSEMBLY OF AXLE

Refer to Part 4-1 of this Shop

Manual for Cleaning and Inspection

procedures before starting assembly

operations.

ASSEMBLY OF

DIFFERENTIAL CASE

1.
Place the ring gear on the differ-

ential case. Install the retaining bolts

and torque them to specification.

2.
If the differential bearings were

removed, press them on as shown in

Fig. 17.

3.
Insert the pinion gear shaft lock

bolt into the case (loosely).

INSTALLATION OF DRIVE

PINION AND

DIFFERENTIAL CASE

1.
Place the shim(s) and pinion rear

bearing cone on the pinion shaft.

Press the bearing and shim(s) firmly

against the pinion shaft shoulder (Fig.

18).

2.
Place a new pinion bearing pre-

load (collapsible) spacer on the pinion

shaft.
REAR BEARING

CONE AND

ROLLER
Press Ram

FIG. 18—Drive Pinion Bearing

Installation

3.
Lubricate the pinion rear bearing

with axle lubricant.

4.
Lubricate the pinion front bear-

ing with axle lubricant. Lubricate the

pinion front bearing cone and place it

in the carrier housing.

5.
Install a new oil seal in the car-

rier casting (Fig. 19).

6. Insert the drive pinion shaft (U-

joint) flange into the pinion seal and

hold it firmly against the pinion front

bearing cone. From the rear of the

carrier casting, insert the pinion shaft

into the flange.

7.
Apply a small amount of lubri-

cant to the washer side of the flange

nut and start the nut. Use a new nut.

Hold the flange with the tool shown in

Fig. 12 and tighten the pinion shaft

nut. As the pinion shaft nut is tight-

ened, the pinion shaft is pulled into

the front bearing cone and into the

flange.

As the pinion shaft is pulled into

the front bearing cone, pinion shaft

end play is reduced. While there is

still end play in the pinion shaft, the

flange and cone will be felt to bottom.

This indicates that the bearing cone

and flange have bottomed on the col-

lapsible spacer.

From this point, a much greater

torque must be applied to turn the

pinion shaft nut, since the spacer must

be collapsed. From this point, also,

the nut should be tightened very slow-

ly and the pinion bearing preload play

checked often, so that the pinion bear-

ing preload does not exceed the speci-

fied limits.

If the pinion shaft nut is tightened

to the point that pinion bearing pre-

load exceeds the limits, the pinion

shaft must be removed and a new col-

lapsible spacer installed. Do not de-

crease the preload by loosening the
/
Tool
-
T58L-4676-A

/ E
1581-A

FIG. 19—Installing Pinion Seal

E 1582-A

FIG. 20—Checking Pinion Bearing

Preload

pinion shaft nut. This will remove the

compression between the pinion front

and rear bearing cones and the col-

lapsible spacer and may permit the

front bearing cone to turn on the pin-

ion shaft.

8. As soon as there is preload on

the bearings, turn the pinion shaft in

both directions several times to seat

the bearing rollers.

9. Adjust the bearing preload to

specification. Measure the preload

with the tool shown in Fig. 20.

10.
Apply a thin coating of lubri-

cant on the bearing bores so that the

differential bearing cups will move

easily.

11.
Place the cups on the bearings

and set the differential case assembly

in the carrier casting.

If the gear set is of the non-hunting

or partial non-hunting type, assemble

the differential case and ring gear as-

sembly in the carrier so that the

marked tooth on the pinion indexes

between the marked teeth on the ring

gear as shown in Fig. 49, Part 4-2.

In almost every case of improper

assembly (gears assembled out of

time),
the noise level and probability

of failure will be higher than they

would be with properly assembled

gears.

When installing the hunting type

gear set (no timing marks), assembleprocarmanuals.com

04-04-10
Rear Axle — Ford Light-Duty (WER)

04-04-10

the differential case and ring gear as-

sembly in the carrier without regard

to the matching of any particular gear

teeth.

12.
Slide the case assembly along

the bores until a slight amount of

backlash is felt between the gear teeth.

Hold the differential case in place.

13.
Set the adjusting nuts in the

bores so that they just contact the

bearing cups.

14.
Carefully position the bearing

caps on the carrier casting. Match the

marks made when the caps were re-

moved (Fig. 21).

15.
Install the bearing cap bolts

and lockwashers. As the bolts are

tightened, turn the adjusting nut with

the tool shown in Fig. 21.

16.
If the adjusting nuts do not turn

freely as the cap bolts are tightened,

remove the bearing caps and again in-

spect for damaged threads or incor-

rectly positioned caps. Tightening the

bolts to the specified torque is done to

be sure that the cups and adjusting
.BEARING CAP IDENTIFICATION-j

MARKS
A

T57L-4067-A

E 1583-A

27—Bearing Cap Installation

nuts are seated. Loosen the cap bolts,

and torque them to only 5 ft-)bs be-

fore making adjustments. Refer to

part 4-1, Section 2 of this shop manu-

al for backlash and bearing preload

adjustment procedures.

17.
Clean the marking compound

from the gear teeth.

18.
Install both side bearing adjust-

ing nut locks (bolts) and torque them

to specification.
19.
Install the differential pinion

side gears and thrust washers.

20.
Install the rear wheel bearings

seals,
rear axle shafts, wheels and tires

and the axle carrier cover as outlined

under Part 4-3, Section 2, Rear Axle

Shaft, Wheel Bearing and Oil Seal

Replacement, Steps 10 through 19.

21.
Raise the axle all the way up.

Rdnove the safety support stands.

22.
Connect the track bar to the

mounting stud. Install the washer and

retaining nut, and torque the nut to

specification.

23.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission.output

shaft. Align the scribe marks on the

cups,
flange and drive shaft and con-

nect the rear end of the drive shaft to

the axle U-joint flange. Torque the re-

taining bolts to specification.

24.
Lower the vehicle.procarmanuals.com

04-05-01
Specifications

04-05-01

PART
4-5
Specifications

REAR AXLE RATIOS. GEAR AND CuDE IDENTIFICATION
-
COUGAR FALCON. FAIRLANE. MUSTANG AND MONTEGO

Identifi-

cation

Tag

WCY-R1

WCY-AJ2

WCZ-F1

WCZ-V

WDJ-C1

WDV-B

WDV-G

WDW-H

WDW-B1

WDW-C1

WDW-F

WDW-J

WDW-K

WDY-A1

WDY-B1

WDZ-B1

WDZ-E

WEA-A1

WEA-F1

WEB-F6

WEB-F6

WEB-H2

WEB-L

WEB-M

WEB-N

WEB-P

WEB-R

WEB-S

WEB-T

WEB-U

WEC-D5

WEC-E5

WEC-H

WEC-J

©2-
Pini

©Torque
Ring Gear

Diameter

(Inches)

7 1/4

7
1/4

8

8

8

7
1/4

7 1/4

7 1/4

8

8

8

8

8

8

8

8

8

8

8

9

9

9

9

9

8 3/4

9

9

9

9

8 3/4

9

9

9

8
3/4
Type
of

Differential®

Conventional

Conventional

Conventional

Conventional

Limited Slip

Conventional

Conventional

Limited Slip

Conventional

Conventional

Conventional

Conventional

Conventional

Conventional

Conventional

Limited Slip

Limited Slip

Limited Slip

Limited Slip

Conventional®

Conventional®

Conventional

Conventional®

Conventional®

Conventional

Conventional®

Conventional

Conventional

Conventional®

Conventional

Conventional®

Conventional®

Conventional®

Conventional
Axle

Ratio

2.83:1

3.08:1

3.00:1

2.79:1

3.00:1

2.83:1

3.20:1

3.20:1

3.00:1

3.25:1

3.00:1

2.79:1

2.79:1

3.00:1

3.25:1

3.00:1

3.00:1

3.00:1

3.25:1

3.00:1

3.25:1

2.75:1

3.50:1

3.00:1

3.00:1

2.75:1

3.00:1

3.25:1

3.25:1

3.25:1

3.00:1

3.25:1

3.00:1

3.00:1
No.
of
Teeth

Ring Gear

34

37

39

39

39

34

32

32

39

39

39

39

39

39

39

39

39

39

39

39

39

44

35

39

39

44

39

39

39

39

39

39

39

39
Pinion

12

12

13

14

13

12

10

10

13

12

13

14

14

13

12

13

13

13

12

13

12

16

10

13

13

16

13

12

12

12

13

12

13

13

on Unless Otherwise Noted ©Conventional
4 •
Pinion

Sensitive Locker
(4 •
Pinion) ©Limited Slip
4 -
Pinion
Identifi-

cation

Tag

WEC-K

WEC-L

WEC-M

WEC-N

WEC-R

WES-F

WES-G1

WES-M

WES-N

WES-P

WES-SI

WES-T1

WES-U

WES-AA

WES-AB

WES-AC

WES-AD

WFA-A

WFA-C

WFA-D

WFA-E

WFB-A

WFB-C

WFC-A

WFC-B

WFC-C

WFC-D

WFC-E

WFC-F

WFOS

WFC-K

WFC-G

WFD-A

WFD-B

WFD-C

WFD-H
Ring Gear

Diameter

(Inches)

9

9

8 3/4

9

9

9

9

9

8 3/4

8 3/4

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9
Type
of

Differential®

Conventional

Conventional®

Conventional

Conventional

Conventional®

Conventional®

Limited Slip®

Conventional®

Conventional

Conventional

Conventional®

Conventional

Conventional®

Conventional

Conventional

Conventional®

Conventional®

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok©

Traction Lok©

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®

Traction LokCD

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®

Traction Lok®
Axle

Ratio

3.00:1

3.25:1

3.25:1

3.25:1

3.50:1

3.00:1

3.25:1

3.25:1

3.00:1

3.25:1

2.75:1

2.75:1

3.50:1

3.00:1

3.25:1

3.00:1

3.25:1

3.25:1

3.25:1

3.25:1

3.00:1

3.25:1

3.25:1

3.50:1

3.91:1

4.30:1

3.91:1

4.30:1

3.91:1

3.50:1

4.30:1

3.00:1

3.50:1

3.91:1

4.30:1

3.25:1
No.
of
Teeth

Ring Gear

39

39

39

39

35

39

39

39

39

39

44

44

35

39

39

39

39

39

39

39

39

39

39

35

43

43

43

43

43

35

43

39

35

43

43

39
Pinion

13

12

12

12

10

13

12

12

13

12

16

16

10

14

12

13

12

12

12

12

13

12

12

10

11

10

11

10

11

10

10

13

10

11

10

12procarmanuals.com

04-05-03
Specifications

04-05-03

SHIM PACK THICKNESS CHART TRACTION-LOK DIFFERENTIAL

Feeler

Gauge

Reading

0.001

0.002

0.003

0.004

0.005

0.006

0.007

0.008

0.009

0.010

0.011

0.012

0.013

0.014

0.015

0.016

0.017

0.018

0.019

0.020

0.021

0.022

0.023

0.024

0.025

0.026

0.027
Remove Shim(s)

From

Nominal

None

0.005

0.010

0.015

0.020

0.025
Total Req'd

Shim Pack

Thickness®

0.050

0.045

0.040

0.035

0.030

0.025
Feeler

Gauge

Reading

0.028

0.029

0.030

0.031

0.032

0.033

0.034

0.035

0.036

0.037

0.038

0.039

0.040

0.041

0.042

0.043

0.044

0.045

0.046

0.047

0.048

0.049

0.050
Remove Shim(s)

From

Nominal

0.030

0.035

0.040

0.045

0.050
Total Req'd

Shim Pack

Thickness ®

0.020

0.015

0.010

0.005

0.000

©Service Shims are available in 0.010" and 0.005" Thicknesses.

ADJUSTMENT TORQUE SPECIFICATION -(BY AXLE RING GEAR DIAMETERS

Description

Minimum torque required to tighten

pinion flange nut to obtain

correct pinion bearing preload

7 1/4" & 8 1/2"

8", 8 3/4" & 9"

9 3/8"

Pinion Bearing Preload-

collapsible spacer)®

Original Bearings 7 1/4"

8", 8 1/2", 8 3/4", 9"

New Bearings 7 1/4"

8", 8 1/2", 8 3/4", 9"

Pinion Bearing Preload-

(Solid Spacer) 9 3/8" Only
Torque

Lbs.
In.

6-12

8-14

17-32

22-32

15-35
. Lbs. Ft.

140®

175®

180-220
Description

Lockers Only • Minimum rotating

Torque required to turn axle

shaft and side gear with one

wheel on ground:

Limited Slip 7 1/4"

All other R. G. Sizes

Traction-Lok-All

Lockers only-Rotating Torques

required during bench check

after assembly:

Original Clutch Plates-

Limited Slip 71/4",

All other R. G. Sizes

Traction-Lok-(All)

New Clutch Plates-

Limited Slip 7 1/4"

All other R. G. Sizes

Traction-Lok-All
Torque

Lbs.
In.
Lbs.
Ft.

50

75

40

50 Min.

75 Min.

40 Min.

100-125

155-195

100-250G

©If pinion bearing preload exceeds specification before this torque is obtained, install a new spacer.

©With Oil Seal.

©Rotating torque may fluctuate up to 40 Lbs. Ft.procarmanuals.com

04-05-04
Specifications

04-05-04

ATTACHING TORQUE SPECIFICATIONS -(By Axle Ring Gear Diameter)

Description

Differential Bearing Cap Bolt- 7 1/4"

8"

All Others

Differential Bearing Adjusting

Nut Lock Bolts

Carrier
to
Housing Stud Nuts-

8", 8 3/4", 9" 8 3/8"

Pinion Retainer
to
Carrier Bolts-

8", 8 3/4", 9" 9 3/8"

Ring Gear Attaching Bolts-

7 1/4"

All Others

Differential Pinion Shaft

Lock Pin
•
8 1/2" Only
Torque Lbs.
Ft.

40-55

55-70

70-85

12-25

25-40

30-45

40-55

65-80

15-22
Description

Rear Cover Screw and Washer

Assemblies
-8
1/4" &
8
1/2

Only

Oil Filler Plug

Rear Axle Shaft Bearing Retainer

Bolt Nuts:

Falcon,
Fairlane, Montego,

Mustang and Cougar (All)

Ford & Meteor (Exc.
8 1/2" R.G.)

Mercury,
T
Bird

Lincoln Continental (All)

Brake Backing Plate Bolt Nuts-

Ford & Meteor
8
1/2" Only
Torque Lbs.
Ft.

25-35

25-50

20-40

50-75

30-55

20-40

LUBRICANT
CAPACITIES
AND CHECKING PROCEDURES®

Vehicle

Falcon,
Mustang

Cougar, Fairlane, Falcon

Montego, Mustang

Ford,
Meteor

Ford,
Meteor

Cougar, Fairlane, Falcon, Ford,

Mercury, Meteor, Montego, Mustang

Lincoln,
Thunderbird
Engine

(C.I.D.)

170,
200

250,
302

240,
302

240,
302

351,
390,

428,
429

429,
460
Axle

Ratio

All

All

2.80:1,
3.10:1

All Except

2.80:1,
3.10:1

All

All
U.S. Measure

Capacity® (Pints)

2.5

4.0

4.0

5.0

5.0

5.0©
Imperial

Capacity
CD
(Pints)

2

31/5

3 1/5

4.0

4.0

4.0©

©All limited slip and Traction-Lok axles use ESW-M2C-104-A lubricant (C6AZ-19580-C).

All conventional axles use ESW-M2C-105-A lubricant (C6AZ-19580-B).

©Approximate refill capacity-Actual lubricant capacities are determined
by
filling
to
bottom
of
filler hole.

©To check these axles, the plug should be backed
out
slowly.
If
seepage occurs around the threads, the plug should
be
turned back
in

immediately to avoid any drainage. This indicates that the specified amount
of
lubricant
is
present
in
the axle.

SPECIAL TOOLS

FORD,
MERCURY, METEOR

Ford Tool No.

T66L-4204-L

T57L-500-A

T50T-100-A

TOOL-4235-C

T00L-4621-A

TOOL-1225-D

T00L42344

TOOL-1177

TOOL-U75-AB

T57L4220-A

T00L4221-AE

T00L-4221-AF

T66P-4220-P

TOOL-4851-K
Former No.

42211 or

42211-A

6005-M

6005-MS

B-160

4235C

—

—

4234-A

4245-B

1175-AB

—

4221-AF

T57L-4851-A

4851-K
Description

Limited-Slip Differential Check

Bench Fixture

Impact Hammer

Axle Shaft Remover

Drive Pinion Bearing and

Rear Wheel Bear Replacer

Rear Wheel Bearing Remover

Rear Wheel Bearing Installer

Rear Wheel Bearing Oil Seal Installer

Rear Wheel Bearing Oil Seal Remover

Differential Bearing Remover

Differential Bearing Remover

U-Joint
Flange Holder
Ford Tool No.

T53T4851-A

T00L4858-D

T57L4614-A

T00L4621-K

T53L-200-A

T57L-4625-A or

T00L4625-K

T57L4616-A or

T00L4615-D

T58L-101-A

T55P4616-A2

T57L4621-B or

T00L4621-L

T58L4676-A

T00L4858-E
Former No.

4851-A, D

—

4614

4621-K

—

4625-K

—

—

—

—

4676-F

4858-E
Description

U-Joint
Flange Remover

U-Joint
Flange Remover

Drive Pinion Retainer Support

Pinion Rear Bearing Cone Remover

Handle Adapter

Pinion Pilot Bearing Remover and

Installer

Pinion Front Bearing Cup Remover

and Replacer

Puller Attachment—For Bearing

Cup Removal

Pinion Rear Bearing Cup Remover

and Replacer

Pinion Rear Bearing Cone Installer

Drive Pinion Oil Seal Replacer

U-Joint
Flange and Pinion Bearing

Replacerprocarmanuals.com