1969 FORD MUSTANG torque

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com

07-01-09

General Transmission Service

07-01-09

For example, on a C4 transmission,

if the pressure at 10 inches of vacuum

was 120 psi and the pressure at 1.0

inch of vacuum was 170 psi, and up-

shifts and downshifts were harsh, a di-

aphragm adjustment to reduce the di-

aphragm assembly spring force would

be required.

If the pressure readings are low, an

adjustment to increase diaphragm

spring force is required.

To increase control pressure, turn

the adjusting screw in clockwise to re-

duce control pressure, back the adjust-

ing screw out by turning it counte-

rclockwise. One complete turn of the

adjusting screw (360 degrees) will

change idle line control pressure ap-

proximately 2-3 psi. After the adjust-

ment is made, install the vacuum line

and make all the pressure checks as

outlined in the Specification Section.

The diaphragm should not be ad-

justed to provide pressure below the

ranges shown in the Specification Sec-

tion in order to change shift feel. To

do so could result in soft or slipping

shift points and damage to the trans-

mission.

ALTITUDE

COMPENSATING TYPE

The altitude—compensating di-

aphragm is provided with an adjust-

ment screw located in the vacuum

connecting tube (Fig. 15). The adjus-

table feature allows control and TV

pressures to be adjusted (within limits)

to correct soft or harsh shift feel.

Control and TV pressures are in-

creased or decreased by turning the

adjusting screw.

Before replacing or adjusting the di-

aphragm, it must first be determined

that the pressure or vacuum is actual-

ly out of specification and that the

cause of the problem is not due to

other items within the transmission or

vacuum connecting lines.

If the tests outlined in the Specifi-
cation Section have been performed

and pressures are within specification

but shift feel is unsatisfactory, or if

the pressure is too high or too low at

10 inches of vacuum, the vacuum di-

aphragm may be adjusted to improve

the shift feel.

If shifts are excessively harsh, the

diaphragm should be adjusted to re-

duce control pressure by backing off

the adjusting screw (counterclock-

wise).
If shift quality is extremely soft,

control pressure should be increased

by turning the adjusting screw inward

(clockwise).

To adjust the vacuum diaphragm to

compensate for harsh shift quality,

first check control pressure in D, 2

and 1 at 10 inches manifold vacuum

and note the pressure reading ob-

tained. Remove the T-fitting from the

vacuum hose and back off the adjust-

ing screw (counterclockwise) by one

full turn. Each full turn will reduce

control pressure by approximately 2

1/2 psi at 10 inches of vacuum. Test

the vehicle for shift feel. If shift quali-

ty is still harsh, a further adjustment

should be made to reduce control

pressure. However, control pressure

should not be reduced below the speci-

fication shown for 10 inches of vacu-

um. If control pressure has been re-

duced to the low limit and shift feel is

still excessively harsh, the clutches and

band should be checked for correct

operation.

To adjust the vacuum diaphragm to

compensate for extremely soft shifts,

record the control pressure reading at

10 inches of vacuum in D, 2 and 1,

then make an initial adjustment of

one full turn inward (clockwise). Test

the vehicle for shift feel and again ad-

just the diaphragm, if necessary. Con-

trol pressure at 10 inches of vacuum

must not exceed the high limit shown

in the Specification Section.

When the necessary adjustments

have been completed and shift feel is

satisfactory, repeat all the tests out-

ADJUSTING

SCREW

PRIMARY

THROTTLE VALVE
DIAPHRAGM

SPRING

D 1639-A

FIG. 15—Altitude Compensating Type Vacuum Diaphragm
lined in the Specification Section. All

tests must be within specifications.

The adjustable vacuum unit must not

be used to allow for adjusting control

or TV pressures that are out of speci-

fications. If these pressures are found

to be out of specifications the cause

must be determined and corrected bef-

ore making any adjustment.

NEUTRAL START SWITCH

ADJUSTMENT AND

REPLACEMENT—COLUMN SHIFT

There are two types of column-

mounted neutral start switches: A and

B.
Type A switch has a parking brake

brake-release vacuum valve. Type B

switches do not have a vacuum valve.

The switches differ in appearance but

not in operation. Both switches are

actuated by a removable steel lever,

which is installed in the shifter tube

within the steering column assembly.

The following procedures outline the

steps necessary to correctly adjust and

replace the neutral start switch.

SWITCH ADJUSTMENT

Neutral Position

1.
With the selector lever held light-

ly against the neutral stop, attempt to

start the engine. If the engine starts

while holding the lever but does not

start when the lever is released, the

shift linkage should be adjusted. If the

engine does not start in either condi-

tion, adjust the switch.

2.
To adjust the switch in neutral,

place the transmission selector lever

against the stop of the neutral detent

position.

3.
Loosen the two retaining screws

that locate the switch on the steering

column (Fig. 16).

4.
With the selector lever against

the neutral stop, rotate the switch

until a start in the neutral position is

obtained. Then, tighten the switch at-

taching screws to 20 in-lbs torque.

5.
With the switch properly adjust-

ed in neutral, place the selector lever

in the 1 position and push the park

reset button (Fig. 16) to the left

(counterclockwise) until it stops. The

park reset must be performed when-

ever the switch has been adjusted.

Park Position

1.
Place the selector lever in the

park position, release the lever and at-

tempt to start. If the engine does not

start, reset the park adjustment.procarmanuals.com

07-01-10
General Transmission Service

07-01-10

2.
To adjust the switch for the park

position, place the transmission selec-

tor lever in 1 and push the park reset

button (Fig. 16) to the left (counter-

clockwise) until it stops.

3.
Check the operation of the

switch in each selector lever position.

The starter should engage in only the

neutral and park positions. Be sure to

perform
the
park reset
if for any rea-

son
the
neutral switch
is
adjusted.

If,
after performing
the
switch
ad-

justments,
the
starter still will
not en-

gage
in the
neutral
or
park positions,

replace
the
switch. Never replace
the

neutral switch until
the
switch adjust-

ments have been made.

SWITCH REPLACEMENT

1.
Disconnect the neutral start

switch wires at the plug connector.

2.
Disconnect the vacuum hoses, if

so equipped.

3.
Remove the two screws securing

the neutral start switch to the steering

column and lift the switch from the

column.

Check the column to be sure the

metal switch actuator is secure to the

shift tube and that it is seated as far

forward against the shift tube bearing

as is possible. Also check for a broken

or damaged actuator. If it is broken

or damaged, replace it as shown in

Figure 17.

4.
Before installing a new switch to

the column, check to see that the red

neutral position gauge inserted in the

neutral pinning hole. If the pin is

missing, align the two holes at the

neutral pinning hole on top of the

switch and install a No. 43 drill or

0.092-0.093 inch gauge pin.

5.
While holding the selector lever

against the stop in the neutral detent
ACTUATOR LEVER INSTALLED

WHEN INSTALLING
THE
ACTUATOR

LEVER
BE
SURE THAT
IT
1$ SEATED

AS
FAR
FORWARD AGAINST
THE
SHIFT

TUBE BEARING
AS IS
POSSIBLE.
FORWARD

D2019-A

FIG. 17—Removing
or
Installing Neutral Start Switch Actuator Lever

position, place the switch on the col-

umn and install the two attaching

screws. Tighten the screws to 20 in-lbs

torque.

6. Remove the gauge pin (or No.

43 drill if used).

7.
Connect the switch wires to the

plug connector and check for a start

in the neutral position. The starter

should engage with the selector lever

against the neutral stop. If not, loosen

the attaching screws and move the

switch just enough to engage the start-

er. Tighten the screws to 20 in-lbs tor-

que.

8. With the switch properly adjust-
ed in neutral, push the park reset but-

ton (Fig. 16) to the left (counterclock-

wise) until it stops. The park reset

must be performed whenever the

switch has been adjusted or replaced.

9. To adjust the switch for the park

position, place the transmission selec-

tor lever in 1 and push the park reset

button (Fig. 16) to the left (counter-

clockwise) until it stops.

10.
Connect the vacuum hoses to

the switch, if so equipped.

11.
Check the operation of the

switch in each selector lever position.

The starter should engage in only the

neutral and park detent positions.

NEUTRAL SWITCH-TYPE
A

(USED
ON
VEHICLES WITH VACUUM

OPFRATED PARKING BRAKE)
NEUTRAL SWITCH-TYPIE
B

(USED
ON
VEHICLES WITHOUT VACUUM

OPERATED PARKING BRAKE)

ATTACHING

FIG.
16—Ad
justing Neutral Switch—Column Shift
D2018-Aprocarmanuals.com

07-01-11
General Transmission Service

07-01-11

STOP
PIN

GROMMET

Tool - T67P-734LA

GROMMET

LEVER

CONTROL ROD REMOVAL
GROMMET INSTALLATION

Tool - T67P-734LA

r

CONTROL ROD INSTALLATION
3/16"-1/4'

CONTROL ROD

STOP
PIN

FIG. 18—Removing
or
Installing Shift Linkage Grommet
D 1742-A

MANUAL SHIFT LINKAGE

GROMMET REPLACEMENT-

COLUMN SHIFT

The manual lever assembly
on ve-

hicles equipped with
a
column shift
in-

corporates
an oil
impregnated plastic

grommet
in the end of the
lever
arm.

A special tool T67P-7341-A
is re-

quired
to
install
the
grommet
in the

manual lever,
and to
install
the
manu-

al linkage
rod
into
the
grommet.
Re-

move
and
install
the
grommet
as fol-

lows:

1.
Place
the
lower
jaw of the
tool

between
the
manual lever
and the con-

trol
rod.
Position
the
stop
pin
against
the
end of the
control
rod (Fig. 18)

and force
the rod out of the
grommet.

Remove
the
grommet from
the
manu-

al lever
by
cutting
off the
large shoul-

der with
a
sharp knife.
The
grommet

must
be
removed from
the
manual

lever
and a new one
installed each

time
the rod is
disconnected.

2.
Before installing
a
new grommet,

adjust
the
stop
pin to 1/2
inch
and

coat
the
outside
of the
grommet with

lubricant. Then, place
the
grommet
on

the stop
pin and
force
it
into
the
man-

ual lever hole. Turn
the
grommet
sev-

eral times
to be
sure
it is
properly

seated.

3.
Readjust
the
stop
pin to the
height shown
in Fig. 18. The pin

height
is
determined
by the
length
of

the
rod end
which
is to be
installed

into
the
grommet.
If the pin
height
is

not adjusted,
the
control
rod may be

pushed
too far
through
the
grommet

causing damage
to the
grommet
re-

taining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
control
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of the
grom-

met.
Be
sure
the rod
protrudes

through
the
grommet approximately

1/4 inch after installation.

CLEANING
AND
INSPECTION

CLEANING

TRANSMISSION

Clean
the
parts with suitable solvent

and
use
moisture-free
air to dry off all

the parts
and
clean
out oil
passages.

The composition clutch plates,

bands
and
synthetic seals should
not

be cleaned
in a
vapor degreaser
or
with
any
type
of
detergent solution.

To clean these parts, wipe them
off

with
a
lint-free cloth.
New
clutch

plates
or
bands should
be
soaked
in

transmission fluid
for
fifteen minutes

before
the
plates
or
bands
are as-

sembled.

CONVERTER

The converter cannot
be
disas-

sembled
for
cleaning.
If
there
is rea-
son
to
believe that
the
converter
con-

tains
an
excessive amount
of
foreign

material,
it
should
be
thoroughly

cleaned.
See the
instructions provided

with
the
Rotunda Automatic Trans-

mission Torque Converter
and
Cooler

Cleaner LRE-60081.

OIL COOLER

When
a
clutch
or
band failure
or

other internal trouble
has
occurred
inprocarmanuals.com

07-01-12
General Transmission Service

07-01-12

the transmission,
any
metal particles

or clutch plate
or
band material that

may have been carried into
the
cooler

should
be
removed from
the
system
by

flushing
the
cooler
and
lines before

the transmission
is put
back into serv-

ice.
In no
case should
an
automatic

transmission having
a
clutch
or
band

failure
or
other internal trouble result-

ing
in
fluid contamination,
be put

back into service without first flushing

the transmission
oil
cooler.

To flush
the oil
cooler, follow
the

instruct!
on >
provided with
the
Rotun-

da Automatic Transmission Torque

Converter
and
Cooler Cleaner
LRE-

60081.

INSPECTION

TURBINE
AND
STATOR
END

PLAY CHECK

A special tool
(Fig. 19)
must
be

used
to
check
the
condition
of the

converter. This special tool
is
used
to

check
the
turbine
and
stator
end
play

and
the
operation
of the
one-way
sta-

tor clutch.

CRUISE-O-MATIC

Too/-T58L-7902-A

C-4 AND C-6 TRANSMISSION

Tool-T59P.7902.Bor 7937-B

ON C-4 AND C-6 TRANSMISSION

Tool-T64L-7902-A
D
1499-E

FIG. 19—Converter Checking Tool

1.
Insert
the
tool (Fig.
19)
into
the

converter pump drive
hub
until
it
bot-

toms.

2.
Install
the
guide over
the con-

verter pump drive
hub.
3.
Expand
the
split fiber bushing
in

the turbine spline
by
tightening
the

adjusting
nut.
Tighten
the
adjusting

nut until
the
tool
is
securely locked

into
the
spline.

4.
Attach
a
dial indicator
to the

tool (Fig.
20 or
21). Position
the
indi-

cator button
on a
converter pump

drive
hub, and set the
dial face
at 0

(zero).

5.
Lift
the
tool upward
as far as it

will
go and
note
the
indicator reading.

The indicator reading
is the
total
end

play which
the
turbine
and
stator

share.
If the
total
end
play exceeds

the limits specified
in
Part 7-5, replace

the converter unit.

6. Loosen
the
adjusting
nut to
free

the split bushing,
and
then remove
the

tool from
the
converter.

STATOR ONE-WAY CLUTCH

CHECK

1.
Install
the
stator outer race hold-

ing tool
in one of the
four holes
pro-

vided
in the
stator (Fig.
20 or 21).

2.
Insert
the
tool
in the
converter

pump drive hub.
As the
tool enters
the

converter,
the
pins will engage
the sta-

tor clutch inner race spline.

3.
Place
a
torque wrench
on the

tool (Fig.
20 or
21).
The
tool (and
sta-

tor inner race) should turn freely

clockwise (from
the
pump drive
hub

inside
the
converter).
It
should lock
up

and hold
a 10
ft-lb pull when
the

wrench
is
turned counterclockwise.

Try
the
clutch
for
lockup
and
hold
in

at least five different locations around

the converter.
On
the
C4
or C6
Auto-

matics,
the
metal ring holding
the

locking tool will have
to be
held
by

hand during this check.

4.
If the
clutch fails
to
lock
up and

hold
a 10
ft-lb torque, replace
the

converter unit.

STATOR
TO
IMPELLER

INTERFERENCE CHECK

1.
Position
the
front pump assem-

bly
on a
bench with
the
spline
end of

the stator shaft pointing
up
(Fig.
22).

2.
Mount
a
converter
on the
pump

so that
the
splines
on the
one-way

clutch inner race engage
the
mating

splines
of the
stator support,
and the

converter
hub
engages
the
pump drive

gear.

3.
While holding
the
pump station-

ary, try
to
rotate the converter counter-

clockwise.
The
converter should
ro-

tate freely without
any
signs
of
inter-

ference
or
scraping within
the
convert-

er assembly.
4.
If
there
is an
indication
of
scrap-

ing,
the
trailing edges
of the
stator

blades
may be
interfering with
the

leading edges
of the
impeller blades.

In such cases, replace
the
converter.

STATOR
TO
TURBINE

INTERFERENCE CHECK

1.
Position
the
converter
on the

bench front side down.

2.
Install
a
front pump assembly
to

engage
the
mating splines
of
the
stator

support
and
stator,
and
pump drive

gear lugs.

3.
Install
the
input shaft, engaging

the splines with
the
turbine
hub (Fig.

23).

4.
While holding
the
pump station-

ary, attempt
to
rotate
the
turbine with

the input shaft.
The
turbine should
ro-

tate freely
in
both directions without

any signs
of
interference
or
scraping

noise.

5.
If
interference exists,
the
stator

front thrust washer
may be
worn,
al-

lowing
the
stator
to hit the
turbine.
In

such cases,
the
converter must
be re-

placed.

The converter crankshaft pilot

should
be
checked
for
nicks
or dam-

aged surfaces that could cause inter-

ference when installing
the
converter

into
the
crankshaft. Check
the con-

verter front pump drive
hub for
nicks

or sharp edges that would damage
the

pump seal.

OUTPUT SHAFT
AND

PRIMARY
SUN
GEAR SHAFT

(FMX TRANSMISSION)

1.
Inspect
the
thrust surfaces
and

journals
for
scores. Inspect
the
inter-

nal gear
for
broken
or
worn teeth.

2.
Inspect
the
aluminum sleeve
for

scores
or
leakage. Inspect
the
ring

grooves
for
burrs.

3.
Inspect
the
keyway
and
drive

ball pocket
for
wear,
and
inspect
the

splines
for
burrs, twist
or
wear.

4.
Inspect
the
output shaft sleeve

for alignment with
the
governor drive

ball (Fig.
24).

5.
Inspect
the
external parking gear

teeth
for
damage
and the
speedometer

drive gear teeth
for
burrs.

6.
If
either
the
output shaft
or
ring

gear
has
been replaced, place
the as-

sembled unit with
the
gear face down

on
the
bench, push
the
shaft down-

ward,
and
check
the
clearance
be-

tween
the top of the
snap ring
and its

groove
(Fig. 25).
If
this clearance
ex-

ceeds 0.002 inch, replace
the
snap ring

with
a
thicker ring
to
reduce
the
clear-

ance
to
less than 0.002 inch. Selectiveprocarmanuals.com

07-01-13

General Transmission Service

Tool -T59P-7902-C

or 7937-

(C4
and
C6)

STATOR CLUTCH INNER RACE

Split Fiber Bushing

END PLAY CHECK

Torque Wrench

Torque Wrench

Tool-T64L.790~2-A

C4 TRANSMISSION

STATOR CLUTCH CHECK

FIG. 20—Typical Converter Checking Tool—C4
and C6
Transmissions
D1842-Aprocarmanuals.com

07-01-14

General Transmission Service

07-01-14

STATOR CLUTCH INNER RACE

Splh Fiber Bushing

END PLAY CHECK

Torque
Wrench

Torque
Wrench

Tool -T58L-7902-B or 7946-A

TURBINE HUB

STATOR CLUTCH CHECK

D1934-A

FIG. 21—Typical Converter Checking Tool—FMX Transmissionprocarmanuals.com

07-02-04
C4 Automatic Transmission

07-02-04

The transmission consists essentially

of a torque converter, planetary gear

train, two multiple disc clutches, a
one-way clutch and a hydraulic con-

trol system (Fig. 3).

The only adjustments on the trans-
mission proper are the intermediate

and low-reverse bands.

TRANSMISSION

MANUAL LEVER
2 IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

CONTROL LINKAGE ADJUSTMENTS

The transmission control linkage

adjustments should be performed in

the order in which they appear in this

section of the manual.

THROTTLE AND DOWNSHIFT

LINKAGE ADJUSTMENTS

Adjusting the throttle linkage is im-

portant to be certain the throttle and

kickdown systems are properly adjust-

ed. The kickdown system should come

in when the accelerator is pressed

through detent, and not before detent.

Refer to Group 10 for detailed

throttle and downshift linkage adjust-

ment procedures.

MANUAL LINKAGE

ADJUSTMENTS

Column Shift

1.
Place the selector lever in the D

position tight against the D stop.

2.
Loosen the shift rod adjusting

nut at point A (Fig. 4 or 5).

3.
Shift the manual lever at the

transmission into the D detent posi-

tion, third from the rear.

4.
Make sure that the selector lever

has not moved from the D stop; then,

tighten the nut at point A to 10-20 ft-

lbs.

5.
Check the transmission operation

for all selector lever detent positions.

Console Shift

1.
Position the transmission selec-

tor lever in D position.

2.
Raise the vehicle and loosen the

manual lever shift rod retaining nut

(Fig. 6, 7 or 8). Move the transmis-

sion manual lever to the D position,

fourth detent position from the back

of the transmission.

3.
With the transmission selector

lever and manual lever in the D posi-

tions,
torque the attaching nut 10 to

20 ft-lbs.

4.
Check the operation of the trans-

mission in each selector lever position.

NEUTRAL START SWITCH

ADJUSTMENT—CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

adjustment procedures.

FORD-METEOR

1.
With the manual linkage proper-
COLUMN SHIFT LEVER

D2020-A

FIG.
4—Manual
Linkage—Column Shift—Ford
and
Meteor

"COLUMN

SHIFT LEVER

POINT
A

SHIFT
ROD

D2021-A

FIG.
5—Typical
Manual Linkage—Column
Shift—Fairlane,

Falcon
and
Montego

ly adjusted, check the starter en-

gagement circuit in all positions. The

circuit must be open in all drive posi-

tions and closed only in park and neu-

tral.

2.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

3.
Remove two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 9).

5.
Move the selector lever back and
forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 9).

6. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

7.
Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch lever contacts the selector

lever actuator. If an adjustment can

not be made by rotating the switch,

loosen the actuator lever attaching

bolt and adjust the lever (Fig. 9).

8. Tighten the neutral start switch

attaching screws. If the actuator lever

was adjusted, tighten the actuator

lever bolt to 6-10 ft-lbs.procarmanuals.com