1969 FORD MUSTANG engine

07-02-08
C4 Automatic Transmission

07-02-08

8. Install the outer downshift lever

and attaching nut, and torque the nut

to specification. Install the downshift

linkage rod to the downshift lever.

9. Install the switch wires. Connect

the wire multiple connector. Check

the operation of the switch in each de-

tent position. The engine should start

only with the transmission selector

lever in N (neutral) and P (park).

SELECTOR LEVER

REPLACEMENT—CONSOLE SHIFT

FORD-METEOR

1.
Raise the vehicle and disconnect

the link assembly from the selector

lever arm (Fig. 6).

2.
Lower the vehicle. Remove the

four screws and plates securing the se-

lector lever handle to the lever. Re-

move the handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

quadrant.

5.
Remove the four bolts that at-

tach the selector lever housing to the

floor pan and remove the selector

lever and housing.

6. Position the new selector lever

and housing assembly on the floor pan

and install the attaching bolts.

7.
Connect the bulb socket to the

quadrant and the neutral start switch

wires to the plug connector.

8. Raise the vehicle and secure the

link assembly to the selector lever arm

with the bushing, insulator, flat wash-

er and cotter pin (Fig. 6). Lower the

vehicle.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tr*rtt control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 7).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.
DETENT PAWL

LOCK NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG. 72—Typical Selector Lever Detent Pawl Adjustment

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se-

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-31bs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 12. With a feeler

gauge, check the clearance between

the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 12.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.
19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

7).

23.
Adjust the linkage as required.

J r the vehicle.

MUSTANG

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 8).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.

5.
Disconnect the dial indicator

light.

6. Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

7.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

8. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

9. Install the selector lever handle.

10.
Position the selector lever as

shown in Figure 12. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearance

should be 0.005 to 0.010 inch. If nec-

essary adjust the height of the detent

pawl as shown in Figure 12.procarmanuals.com

07-02-11
C4 Automatic Transmission
07-02-11

REMOVAL AND INSTALLATION

An oil impregnated plastic grommet

is incorporated in the end of the man-

ual shift linkage lever arm on all col-

umn shift vehicles. A special tool

T67P-7341-A is required to install the

grommet in the manual lever, and to

install the manual linkage rod into the

grommet. Refer to Part 7-1, Section

2,
for the grommet replacement pro-

cedures.

TRANSMISSION REMOVAL

1.
Raise the vehicle and remove the

converter cover attaching bolts, at the

lower front side of the converter hous-

ing. Remove the cover.

2.
Remove the two conveter drain

plugs (Fig. 20). Drain the fluid from

the converter. Install the two convert-

er drain plugs.

3.
Remove the drive shaft and in-

stall the extension housing seal repla-

cer tool in the extension housing.

4.
Remove the vacuum line hose

from the transmission vacuum unit.

Disconnect the vacuum line from the

retaining clip.

5.
Remove the two extension

housing-to-crossmember attaching

bolts.

6. Remove the speedometer cable

from the extension housing.

7.
Disconnect the exhaust pipe

flange from the manifolds.

8. Remove the parking brake cable

from the equalizer lever.

9. Remove the fluid filler tube from

the pan and drain the transmission

fluid on PEA models. On PEB and

PEE models, loosen the transmission

CONVERTER A
ATT,
pan bolts and drain the fluid at one

corner of the pan. Tighten the attach-

ing bolts after the fluid has drained.

10.
Disconnect the fluid cooler lines

from the transmission case.

11.
Remove the manual and kick-

down linkage rods from the transmis-

sion control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to remove

the selector rod from the manual

lever.

12.
On a Mustang, disconnect the

neutral start switch wires from the re-

taining clamps and connectors.

13.
Disconnect the starter cable.

Remove the starter attaching bolts

and remove the starter from the con-

verter housing.

14.
On PEB and PEE models, lift

the fluid filler tube from the case.

15.
Remove the four converter-

to-flywheel attaching nuts.

16.
Position the transmission jack

to support the transmission and secure

the transmission to the jack with a

safety chain.

17.
Remove the four crossmember

attaching bolts and lower the

crossmember.

18.
Remove the five converter

housing-to-engine attaching bolts.

Lower the transmission (Fig. 21) and

remove it from under the vehicle.

TRANSMISSION

INSTALLATION

1.
With the converter properly in-

D 2043-A

FIG. 20—Converter Drain Plug

Location
FIG. 21—Transmission Mounted

on Jack
stalled, place the transmission on the

jack (Fig. 21). Secure the transmission

to the jack with the safety chain.

2.
Raise the transmission into posi-

tion and install the five converter

housing-to-engine attaching bolts.

Torque the bolts to specification. Re-

move the safety chain from the trans-

mission.

3.
Position the crossmember and

install the four attaching bolts. Torque

the bolts to specifications.

4.
Lower the transmission and in-

stall the extension housing and

crossmember attaching bolts. Torque

the bolts to specification.

5.
Install the four flywheel to con-

verter attaching nuts. Torque the nuts

to specification.

6. Remove the transmission jack.

Install the fluid filler tube in the

transmission case or pan. Install the

vacuum hose on the transmission vac-

uum unit. Install the vacuum line re-

taining clip.

7.
Connect the fluid cooling lines to

the transmission case.

8. On a Mustang, connect the neu-

tral start switch wires to their respec-

tive connectors and secure the harness

in the retaining clamps.

9. Install the linkage rods on the

transmission downshift and manual

control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to install

a new grommet in the manual lever,

and to install the manual linkage rod

into the grommet.

10.
Connect the speedometer cable

to the extension housing.

11.
Connect the exhaust inlet pipes

to the manifolds.

12.
Install and adjust the parking

brake cable at the equalizer lever.

13.
Install the converter housing

cover and torque the attaching bolts

to specification.

14.
Install the starter and torque

the attaching bolts to specification.

Connect the starter cable.

15.
Install the drive shaft. Torque

the companion flange U-bolts attach-

ing nuts to specification.

16.
Lower the vehicle. Fill the

transmission to the proper level with

the specified fluid. Adjust the manual

and downshift linkage.procarmanuals.com

07-02-16

C4 Automatic Transmission
07-02-16

COVER SEAL

STEM NUT

SERVO PISTON STEM

PISTON RETURN SPRING PISTON AND SEAL

(SEAL BONDED TO PISTON)

FIG. 43—Low-Reverse Servo Disassembled

PARTS REPAIR OR

REPLACEMENT

During the repair of the sub-

assemblies, certain general instructions

which apply to all units of the trans-

missions must be followed. These in-

structions are given here to avoid un-

necessary repetition.

Handle all transmission parts care-

fully to avoid nicking or burring the

bearing or mating surfaces.

Lubricate all internal parts of the

transmission before assembly with

clean automatic transmission fluid. Do

not use any other lubricants except on

gaskets and thrust washers which may

be coated with vaseline to facilitate

assembly. Always install new gaskets

when assembling the transmission.

Tighten all bolts and screws to the

recommended torque as outlined in

the Specification Section.

TRANSMISSION CASE AND

LINKAGE REPAIR

Low-Reverse Servo

1.
Remove the four servo cover-

to-case attaching bolts. Remove the

vent tube and retaining clip from the

case.

2.
Remove the servo cover, cover

seal, servo piston and piston return

spring from the case (Fig. 43).

3.
The servo piston seal is bonded

to the piston. If the seal has to be re-

placed, replace the piston assembly

which includes the seal. Disassemble

the servo piston from the piston stem

by inserting a small screwdriver in the

hole of the piston stem and removing

the piston attaching nut (Fig. 44).

Position the accumulator spring and

spacer (Fig. 43) on the piston stems.

Make sure the crowned side of the

spring is facing toward the rod. Install

the new servo piston and attaching nut
COVER

D1880-A

LOW-REVERSE

PISTON

D1881-A

FIG. 44—Removing or Installing

Low-Reverse Servo Piston

on the stem, torque the nut to specifi-

cation.

4.
Place the piston return spring in

the servo bore of the case. Lubricate

the piston seal with clean transmission
fluid and install the servo pistion into

the bore of the case.

5.
Place a new cover seal on the

cover and install the servo cover. In-

stall the vent tube and retaining clip.

Install the four cover attaching bolts.

Torque the cover-to-case retaining

bolts to specifications.

Intermediate Servo

1.
Remove the transmission
identif-

ication tag and the four servo cover to

case attaching bolts.

2.
Remove the servo cover, gasket,

servo piston, and piston return spring

from the case (Fig. 45).

3.
Remove the intermediate servo

piston from the cover.

4.
Remove the seal rings from the

servo piston and cover.

5.
Install a new seal on the cover

and servo piston. Figure 46 shows the

correct servo piston and cover for

each transmission model. Lubricate

the seals with clean transmission fluid.

Install the piston into the cover. Be

careful not to damage the piston seal.

6. Install the piston return spring in

the servo bore of the case.

7.
Place a new gasket on the servo

cover. Position the servo piston and

cover assembly into the case with the

piston stem slot in a horizontal posi-

tion to engage the strut. Use two

5/16-18 bolts, 1 1/4 inch long, 180

degrees apart, to position the cover

against the case. Install two cover at-

taching bolts. Remove the two 1 1/4

V-8 ENGINE

COVER

RETURN SPRING

PISTON
COVER SEAL COVER^ GASKET

PISTON SEALS

6 CYLINDER ENGINE
COVER

D1882-A

FIG. 45—Intermediate Servo Disassembledprocarmanuals.com

07-02-17

C4 Automatic Transmission

07-02-17

Vehicle

Ford,
Meteor

Fairlane,

Montegc,
Falcon,

Mustang

Ford,
Meteor

Fairlane,

Montego,
Mustang

Mustang

Falcon
Engine

302-2V

302-2V

240-IV

250-1V

200-1V

170-1V

200-1V
Transmi ssion

PEA-MI,
Nl

PEE-M,
V, AC

PEA-A2

PEE-AD,

AE,
AF

PEB-B2

PEB-C2
Servo Piston

Dia.
A

3.7875

3.7875

3.3265
Dia.
B

2.8265

2.7065

2.4865
Servo Cover

Dia.
C

None

None

3.340
Dia.
D

2.840

2.975

2.500
Spring

Free Length

(Inches)

2.480

2.480

2.480
Color

Cniif

White

White

White

D 1800-D

FIG. 46—Intermediate Servo Piston, Cover and Spring Identification

inch bolts and install the transmission

identification tag and the other two

cover attaching bolts. Torque the bolts

to specifications.

Downshift and Manual

Linkage

1.
Apply penetrating oil to the

outer lever attaching nut to prevent

UPPER RETAINING RING
breaking the inner lever shaft. Remove

the downshift outer lever nut. Remove

the downshift outer and inner lever.

From inside the transmission case, re-

move the upper retaining ring from

the manual lever link (Fig. 47). Re-

move the upper end of the lever link

from the case retaining pin.

2.
From the back of the transmis-

sion case, remove the upper retaining

INNER MANUAL

'ER ATTACHING NUT

mmMm

INNER MANUAL LEVER MANUAL LEVER LINK

FIG. 47—Case Internal Linkage
ring and flat washer from the parking

pawl link (Fig. 48). Remove the pawl

link from the case retaining pin.

3.
From the back of the transmis-

sion case, remove the parking pawl

link, toggle rod, and manual lever link

as an assembly (Fig. 49).

UPPER

r RETAINING

RING

D1885-A

FIG. 48—Parking Pawl Link

/7^-MANUAL LEVER LINK

D1405-B
FIG. 49—Removing or Installing

Parking Pawl Link

4.
Remove the rear parking pawl

link lower retaining ring, flat washer

and link from the toggle rod (Fig. 50).

5.
Remove the manual lever link,

lower retaining ring, flat washer, and

link from the toggle rod.

6. Install the manual and marking

pawl links, flat washers and retaining

rings to the toggle rods.

7.
Remove the inner manual lever

attaching nut and lever. Remove the

outer manual lever from the case.

8. To remove the manual lever seal,

use the tools shown in Fig. 51. To in-

stall the new seal, use a driver that fits

the ID of the seal.

9. Install the outer manual lever in

the case. Install the inner manual

lever and attaching nut with the cham-

fer facing toward the lever (Fig. 47).

Torque the nut to specification.

10.
From the back of the transmis-

sion case, install the parking toggle

rod and link assembly into the case

(Fig. 49).

11.
Install the parking pawl link on

the case retaining pin. Install the flat

washer and link retaining ring (Fig.

48).procarmanuals.com

07-03-01
FMX Transmission

07-03-01

PART
7-3 FMX
Transmission

SELECTOR

TRANSMISSION ENGINE LEVER

MODEL MODEL LOCATION

PHB-A 390-2V Column

PHB-C 351-2V Column

PHB-D 351-2V Console

PHB-E 351-2V Console

PHB-F 351-4V Column

PHB-G 351-4V Console

PHB-H 351-4V Console

PHD-A 240-1V Column

PHD-B 302-2V Column
MODEL APPLICATION
All
Models
Ford

X

X

X
Mercury
Meteor
X

X

X
Cougar
X

X
Fairlane
X

X

X

X
Falcon
Montego
X

X

X

X
Mustang
X

X
Lincoln-
Continental
Thunderbird
Continental-
Mark III

COMPONENT INDEX

ASSEMBLY
OF
TRANSMISSION

End Play Check

BAND ADJUSTMENTS

Front Band

Rear Band (Ford
and
Meteor)

Rear Band (Fairlane, Montego, Mustang
and

Cougar)

External Adjustment

Internal Adjustment

CENTER SUPPORT, ONE-WAY CLUTCH

AND PINION CARRIER

Assembly

Center Support With Chamfered Edge

Center Support
not
Chamfered

Inspection

CONTROL VALVE BODY

Assembly

Disassembly
and
Overhaul

Inspection

Removal
and
Installation

DESCRIPTION

DISASSEMBLY
AND
OVERHAUL
OF

TRANSMISSION

End Play Check

DOWNSHIFT LINKAGE

Adjustment

Parts Repair
or
Replacement

EXTENSION HOUSING

Assembly

Inspection

EXTENSION HOUSING BUSHING

Page
03-26

03-08

03-09

03-09

03-10

03-10

03-10

03-26

03-26

03-27

03-14

03-28

03-21

03-16

03-11

03-03

03-16

03-16

03-05

03-25

03-28

03-14
COMPONENT INDEX

Removal
and
Installation

EXTENSION HOUSING REAR SEAL

Removal
and
Installation

FLUID FILTER ASSEMBLY

FRONT CLUTCH

Assembly

Disassembly
and
Overhaul

Inspection

FRONT PUMP

Assembly

Disassembly
and
Overhaul

Inspection

FRONT SERVO

Assembly

Disassembly
and
Overhaul

Inspection

Removal
and
Installation

GOVERNOR

Assembly

Disassembly
and
Overhaul

Inspection

Removal
and
Installation

MANUAL LINKAGE

Adjustments

Parts Repair
or
Replacement

NEUTRAL START SWITCH-CONSOLE SHIFT

Adjustment

Removal
and
Installation

(Refer
to
Part 7-1
for
Column Shift

Adjustment
and
Removal
and
Installation

procedures)

1

Page
03-13

03-13

03-29

03-26

03-19

03-15

03-28

03-20

01-15

03-28

03-24

01-16

03-12

03-28

03-24

01-16

03-10

03-05

03-25

03-05

03-07
procarmanuals.com

07-03-03
FMX Transmission

0703-03

PRIMARY DISTRIBUTOR SLEEVE EXTENSION HOUSING SEAL

SUN GEAR ! SPEEDOMETER DRIVE GEAR /

OIL SEAL ONE-WAY CLUTCH

FRONT FRONT

PUMP BAND

FRONT

CLUTCH

OUTPUT SHAFT

EXTENSION HOUSING

SPLINE SEAL

GOVERNOR

PRIMARY PINION

SECONDARY SUN GEAR

SECONDARY PINION

DIAPHRAGM

CONTROL VALVE BODY

OIL PAN

TURBINE SHAFT

FLYWHEEL
'REAR CLUTCH PISTON

REAR CLUTCH

REAR CLUTCH SPRING

FRONT CLUTCH PISTON

FRONT SERVO

PRESSURE REGULATOR BODY

STATOR SUPPORT

D 2045-A

FIG. 7—Typical FMX Transmission

TRANSMISSION MODEL

ENGINE DISPLACEMENT
BUILD DATE

FMX TRANSMISSION
SHIFT

D 2046-A

FIG. 2—Identification Tagsprocarmanuals.com

07-03-07
FMX Transmission

07-03-07

Gauge Pin

(No.
43 Drill)

NEUTRAL START

SWITCH

ADJUSTMENT

SCREWS

D 1759-A

FIG. 8—
Neutral
Start Switch-

Console Shift—Fairlane-Montego

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
With the manual linkage proper-

ly adjusted and the engine turned off,

place the selector lever in the N (Neu-

tral) position. Then, shift the selector

lever from neutral to 1, to P (park)

and back to neutral. Shifting the se-

lector lever through this shift pattern

should adjust the switch automatical-

ly. If not, adjust it manually as fol-

lows:

2.
With the selector lever in neu-

tral,
remove the selector lever handle

attaching screw and remove the

handle (Fig. 7).

3.
Remove the dial housing attach-

ing screws and remove the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.
NEUTRAL START SWITCH

AND HARNESS ASSEMBLY

32027-A

FIG. 9—Neutral Start Switch—Console Shift—Mustang-Cougar

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing.

6. Lift the switch from the housing

and move the actuator lever all the

way to the left. Then, return the actu-

ator lever to the neutral position as

shown in Figure 9.

7.
Position the neutral switch as-

sembly to the selector lever housing,

and secure with the two attaching

screws.

8. Place the selector lever in the P

(Park) position and check the opera-

tion of the switch. The engine should

start with the selector lever in the

park position. If the engine does not

start, replace the switch. Refer to the

Neutral Start Switch Replacement

procedures in this section.

9. Install the pointer back-up shield

on the housing and lever assembly.

10.
Install the dial housing on the

selector lever housing assembly.

11.
Install the selector lever.'handle.

NEUTRAL START SWITCH

REPLACEMENT-

CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

replacement procedures.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 8).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.procarmanuals.com

07-03-09
FMX Transmission

07-03-09

4.
Remove the pointer back-up

shield attaching screws and the shield.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

8. Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

9. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

10.
Install the selector lever handle.

11.
Position the selector lever as

shown in Figure 10. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearince

should be 0.005 to 0.010 inch. If nec-

essary, adjust the height of the detent

pawl as shown in Figure 10.

12.
Remo"~ the handle from tte se-

lector lever.

13.
Install the selector housing and

lever assembly as shown in Figure 4.

Torque the attaching bolts 4-6 ft-lbs.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the pointer back-up

shield and tighten the attaching

screws.

17.
Install the selector lever handle

and tighten the attaching screw.

18.
Position the selector lever in the

D position.

19.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

20.
Lower the vehicle and check the

transmission operation in each selec-

tor lever detent position.

BAND ADJUSTMENTS

FRONT BAND

ADJUSTMENT

1.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Use a clean

drain can equipped with a 100-mesh

screen if the fluid is to be reused.
Too/—
7225-C-13B

/A
-inch
Spacer
FRONT SERVO

ACTUATING LEVER

D 2048-A

FIG.
7
7—Adjusting Front Band—

Typical

2.
Remove the pan, then remove

the fluid filter and clip from the trans-

mission. Clean the inside of the pan.

Remove all gasket material from the

pan and pan mounting face of the

case.

3.
Loosen the front servo adjusting

screw lock nut.

4.
Pull back on the actuating rod,

and insert the 1/4 inch spacer between

the adjusting screw and servo piston

stem (Fig. 11). Tighten the adjusting

screw to 10 in-lbs. torque. Remove the

spacer and tighten the adjusting screw

an additional 3/4 turn. Hold the ad-

justing screw stationary and tighten

the lock nut securely.

5.
Install the transmission fluid

screen and clip. Install the pan using a

new gasket.

6. Refill the transmission to the

FULL mark on the dipstick.

7.
Start the engine and engage the

transmission in each drive range to fill

all fluid passages, then place the selec-

tor lever in the P position. Check the

fluid level and add enough fluid to

bring the level above the ADD mark

on the dipstick.

ALTERNATE FRONT

BAND ADJUSTMENT

1.
Drain the fluid from the trans-

mission. If the same fluid is to be

used again in the transmission after

Che band adjustment, filter the fluid

through a 100-mesh screen as it drains

from the transmission. Re-use the

fluid only if it is in good condition.

2.
Remove and thoroughly clean

the pan and screen. Discard the pan

gasket.

3.
Loosen the front servo adjusting

screw locknut two full turns with a
inch Driv

Detail #2

D.tai\
#3

T-Hond/e
Extension

Tool-758L-7195-A
f/2 inch Driv

Detail
#7

Qj-«—
TM-470 TM-82

D1950-A

FIG. 12—Front and Rear Band

Adjusting Tools

9/16-inch wrench. Check the. adjusting

screw for free rotation in the actuating

lever after the lock nut is loosened,

and free the screw if necessary.

4.
Pull the adjusting screw end of

the actuating lever away from the

servo body, and insert the 1/4 inch

spacer (Fig. 12) between the servo pis-

ton stem and the adjusting screw.

5.
Install the socket handle on the

9/16-inch socket.

6. Insert the T-handle extension

through the socket handle and socket,

and install the screwdriver socket on

the T-handle extension.

7.
Place the tool on the adjusting

screw so that the screwdriver socket

engages the screw and the 9/16-inch

socket engages the lock nut.

8. With a torque wrench on the T-

handle extension, tighten the adjusting

screw to 10 in-lbs torque.

9. Remove the spacer and tighten

the adjusting screw an additional 3/4

turn. Hold the adjusting screw station-

ary, and torque the lock nut to speci-

fication.

10.
Place a new gasket on the pan,

and install the screen and pan on the

transmission.

11.
Fill the transmission with fluid.

REAR BAND ADJUSTMENT—

FORD-METEOR

1.
Fold back the floor mat to ex-

pose the right side of the floor pan.

2.
Remove the access hole cover

from the floor pan. Remove all dirt

from the adjusting screw threads, then

oil the threads.

3.
Loosen the rear band adjusting

screw lock nut with the tool shown in

Fig. 13. Using the T-handle portion of

the tool, tighten the adjusting screw

until the wrench overruns.procarmanuals.com