1967 CHEVROLET CAMARO wheel

FRONT SUSPENSION 3-16

available the following procedure may also be

used (fig. 22-Alternate Method).

1.
Support car on suitable hoist or jack (so control

arms may swing free) and remove the wheel and

tire assembly, shock absorber, and stabilizer link

at control arm.

2.
Place suitable jack stand under the lower control

arm cross shaft.

3.
Follow Steps 2-5 as outlined on previous page.

4.
Turn head of tool screw to partially compress

spring.

5. Remove the three control arm cross shaft attaching

bolts,
washers and nuts.

6. Carefully lower jack stand and if necessary increase

compression on spring and when coil spring is out of

its upper seat, relax tension on spring (fig. 22).

7. By using a pry bar to assist, if necessary, remove

the coil spring from the lower control arm.

8. Installation is the reverse of the above procedure.

Carefully follow instructions for installing spring

tool.

LOWER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The lower control arm spherical joint should be re-

placed whenever wear is indicated in the upper joint

inspection.

NOTE: The lower control arm spherical joint

is a loose fit in the assembly when not connected

to the steering knuckle.

Only if inspection of each upper joint indicates them

both to be within limits, inspect each lower joint for ex-

cessive wear as follows:

1.
After reconnecting upper joints to steering knuckles,

support vehicle weight on wheels or wheel hubs.

2.
With outside micrometer or caliper, measure dis-

tance from top of lubrication fitting to bottom of ball

stud, and record the dimensions for each side.

3.
Then support vehicle weight at outer end of each

lower control arm, so that wheels or wheel hubs are

free,
then repeat Step 2.

4.
If the difference in dimensions on either side is

greater than 1/16" (.0625"), the joint is excessively

worn and both lower joints should be replaced.

If inspection of lower spherical joints does not indicate

excessive wear, inspect further as follows:

5.
On Chevrolet Only--Examine lubrication hole in each

joint assembly after cleaning out hole. Look for evi-

dence of the liner partially or fully blocking lubrica-

tion opening. Such evidence indicates that liner is

disintegrating and that both lower spherical joints

should be replaced.

Another indication of lower spherical joint excessive

wear is indicated when difficulty is experienced when

lubricating the joint. If the liner has worn to the point

where the lubrication grooves in the liner have worn

away, then abnormal pressure is required to force lubri-

cant through the joint. This is another reason to recom-

mend replacement of both lower joints.

If the above inspections do not indicate any reason for

spherical joint replacements, test the torque tightness of
Fig. 27 - Removing Lower Ball Joint - Chevelle
&
Camaro

the lower ball stud in the knuckle on each side as follows:

1.
Wire-brush off nut and cotter pin attaching spherical

joint ball stud to steering knuckle and examine for

evidence of looseness of stud in knuckle.

2.
If no evidence of looseness, remove cotter pin and

with prick punch or equivalent, mark nut stud and

knuckle to identify relative location.

3.
Tighten nut as installed and observe torque reading.

If less than 45 lbs. ft., stud may have been loose in

steering knuckle and replacement of both lower

spherical joints may be recommended.

4.
Check to see if torque of 60-94 lbs. ft. can be ob-

tained without bottoming stud or ball joint against

knuckle. If bottoming occurs, replace ball joint or

steering knuckle.

Chevrolet and Corvette

Removal

1.
Support lower control arm at outer end on floor jack,

with hoist or jack pad clear of lower ball stud nut.

2.
Remove upper and lower ball stud nuts, free ball

studs from steering knuckle and wire knuckle and

brake drum assembly up to fender skirt to preclude

interference while performing next step.

3.
Being careful not to enlarge the holes in control arm,

cut off rivets.

Installation

1.
Install new joint against underside of control arm and

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-17

4.
Replace the wheel and tire.

5.
Lower the vehicle.

Chevy II

inspection

Fig.
28 - Installing Lower Ball Joint - Chevelle & Camaro

retain in place with special bolts and nuts supplied

with new joint.

CAUTION: Use only alloy bolts supplied for

this operation. The special thick headed bolt

must be installed in the forward side of the

control arm.

2.
Tighten bolts and nut on ball stud to Specification

shown at the end of this book.

3.
Lubricate the joint.

Chevelle and Camaro

Removal

1.
Support lower control arm at outer end of floor jack,

with hoist or jack pad clear of lower ball stud and

remove the wheel.

2.
Remove the upper and lower ball stud nuts, free the

ball studs from the steering knuckle and wire the

knuckle and brake drum assembly out of the way to

preclude interference while completing the lower ball

stud removal procedure.

3.
Use a screw driver to pry off the seal and retainer.

Install Tools J-9519-10, J-9519-17 and J-9519-7 as

shown in Figure 27 and turn down on the hex head

screw until the ball stud is pushed out.

Installation

1.
Start the replacement ball stud into the control arm

and install Tools J-9519-10, J^9519-16 and J-9519-17

as shown in Figure 28.

2.
Turn down on the hex head screw until the ball stud

is seated properly in the control arm.

3.
Install the stud into the steering knuckle, secure in

place with the attacking nut and install the cotter pin.
1.
With upper control arm support in position as in

Figure 15, disconnect the lower ball stud from steer-

ing knuckle.

2.
Assemble nut to lower ball stud and check rotating

torque with torque wrench. Specifications for new

joints are 9 lbs. ft. If torque readings are exces-

sively high or low, replace ball joint.

Removal

1.
While vehicle weight is still on front wheels, position

support between upper control arm and frame side

rail (fig. 15).

2.
Raise vehicle and remove cotter pin and nut from

lower ball joint stud (fig. 29).

3.
Disconnect stabilizer at upper link. Break loose the

lower ball stud. Drop lower control arm until lower

ball joint is easily accessible.

, 4. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

NOTE: Additional support to lower control

arm will be necessary to perform this operation.

5.
Remove ball joint from arm and clean arm.

6. Inspect ball joint seat and rivet holes for evidence of

fatigue such as cracking or bending. If defects are

evident, replace lower control arm as outlined later

in this section.

Installation

1.
Install ball joint in arm using special bolts furnished

with replacement kit.

NOTE: Use only special hardened bolts fur-

nished with this replacement kit. Do not attempt

to use other non-hardened bolts and do not at-

tempt to rivet replacement ball joint to arm.

Fig.
29- Disassembling Lower Ball Stud - Chevy

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-18

CHEVROLET
CHEVELLE

CAMARO (TYPICAL)

CHEVY U
LOWER CONTROL ARM

CORVETTE

Fig.
30 - Lower Control Arm Attachment

2.
Raise lower control arm and insert ball stud into

steering knuckle lower boss. Install nut and insert

new cotter pin. Install stabilizer linkage.

Lube Fittings

Special self threading type lube fittings are used in the

spherical joint assemblies. If it is necessary to replace

a fitting a standard threaded type may be used. However,

replacement spherical joint assemblies are supplied less

the lube fitting. Therefore it will be necessary to install

a self threading type fitting into the untapped hole pro-

vided when replacing the entire assembly.

LOWER CONTROL ARM

Chevrolet (Fig. 30)

Removal

1.
Remove the coil spring as outlined previously.

2.
Remove lower control arm ball stud cotter pin and

loosen nut. Loosen the ball stud, then remove nut

and lower control arm.

CAUTION: Use extreme care not to damage

the seal during this operation.
Installation

1.
Insert lower control arm ball stud into the steering

boss,
install the nut and insert new cotter pin.

2.
Install the coil spring as outlined previously.

3.
Tighten nuts to torque shown in Specifications.

Chevelle and Camaro (Fig. 30)

Removal

1.
Remove the front coil spring as outlined previously.

2;
Remove the two control arm to frame and cross-

member bracket attaching bolts and lock washers.

3.
Remove the lower control arm assembly.

Installation

1.
With the control arm in place in frame and cross-

member brackets, install the front and rear attaching

bolts,
nuts and lock washers.

2.
Install the coil spring as outlined under "Front Coil

Spring - Installation".

3.
Tighten the nuts to torque shown in Specifications.

Chevy II (Fig. 30)

Removal

1.
With vehicle weight still on front wheels, install

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-21

Chevy II

Removal

1.
Support control arm on Tool J-7 574-4 and insert

Spacer J-9514 (fig. 34).

2,
Press bushing out with Tool J-9226 and Handle

J-7079-2 (fig. 34).

Installation

With Spacer J-9514 still in control arm, invert control

arm and press in new bushing with Tool, J-7474-2 and

Handle J-7079-2 until bushing is fully seated.

CAUTION: It should be noted that control arm

bushing diameters are unequal and bushing must

be pressed into position through larger diameter

only.

CROSS SHAFT AND/ON BUSHINGS

Corvette

Removal

1.
Remove bolt, lock washer and collar from each end

of cross shaft.

2.
Thread a 7/16 x 20 capscrew (furnished with Tool

J-5888) to the bottom of the threads in one end of the

cross shaft.

3.
Support control arm in an arbor press on Tool

J-5888-3,
as shown in Figure 35.

NOTE:
Be certain bushing flange does not

contact support.

4.
Press on cap screw until bushing is free of control

arm. Discard bushing.

5. Remove cap screw from cross shaft. Insert it in

other end of shaft. Invert control arm on support.

Again be certain bushing flange does not contact

support.

6. Press on cap screw until bushing is free of control

arm. Discard bushing.

Installation

1.
With cross shaft in control arm and Tool J-7052-1

in position, place control arm on Tool J-5888-3.

Hand start bushing into control arm and over end of

cross shaft.

NOTE:
The end of the shaft with the two bolt

holes should be toward front of control arm.

2.
Install Tool J-7052-5 over bushing. Be certain

three-piece spacer is not over-lapping bushing holes

in control arm.

3.
Press bushing into control arm until flange contacts

control arm (fig. 36).

4.
Invert arm in press and repeat the process on the

other bushing. After installation, cross shaft should

be free enough to be rotated by hand.

5. Install collar, lock washer and cap screw in each end

of cross shaft. Tighten to torque shown in Specifica-

tions after spring installation.
UPPER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The upper spherical joint is checked for wear by

checking the torque required to rotate the ball stud in the

assembly. After performing the first four steps under

"Replacement" below, install a stud nut on the stud and

measure the torque required to turn the stud in the as-

sembly with a torque wrench. Specified torque for a new

joint is 9 lbs. ft. If torque readings are excessively

high or low, replace the ball joint. If excessive wear is

indicated in upper joint, both upper and lower joints

should be replaced.

NOTE:
This inspection does not necessitate

upper control arm removal.

Replacement

1.
Support the vehicle weight at the outer end of the

lower control arm.

2.
Remove the wheel and tire assembly.

3.
Remove cotter pin and nut from upper control arm

ball stud.

4.
Remove the stud from knuckle.

5. Cut off the ball joint rivets with a chisel.

6. Install new joint and retain in place with the special

nuts and bolts supplied.

7. Reassemble ball stud to the steering knuckle.

Chevy II

Inspection

The following on-the-vehicle check is to determine ball

joint wear.

NOTE:
The upper ball joint is a loose fit when

not connected to the steering knuckle. Wear may

be checked without disassembling the ball stud

by
using'
the following procedure:

1.
While vehicle weight is still on front wheels, insert

upper control arm support as shown in Figure 14.

2.
Raise vehicle and allow wheel and tire to hang free.

3.
Measure distance from tip of ball stud to top surface

of control arm.

4.
Place adjustable jackstand under tire and raise

slightly to take up ball joint looseness.

5. Repeat Step 3 and if the difference in measurements

exceeds 3/32", the joint is excessively worn and

should be replaced.

Replacement

1.
With vehicle weight still on front wheels, install

spacer between upper control arm and frame side

rail (fig. 15). Raise vehicle.

2.
Remove wheel and tire.

3.
Disconnect stabilizer link (if present) and strut rod

at lower control arm.

4.
Remove cotter pin and nut from upper ball joint stud.

5. Break ball stud loose. Drop lower control arm,

steering knuckle and brake assembly with an adjust-

able jackstand until upper control arm ball joint is

easily accessible.

6. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION
3-22

CHEVROLET

s-L 1 \
TYPICAL
OF

-^-x ^K CORVETTE, CHEVELLE AND CAMARO

CHEVY n

Rg.
37 - Upper Control Arm Attachment

NOTE:
Additional support to upper control

arm may be necessary while chiseling.

7. Clean ball joint seat in arm and inspect for cracking

or other evidence of fatigue. If cracks are present at

the rivet holes or ball joint opening, replace arm as

outlined later in this section.

8. Attach replacement ball joint assembly to the control

arm, using special bolts furnished with replacement

kit.

NOTE:
Use only special hardened bolts fur-

nished with this replacement kit. Do not attempt

to use other non-hardened bolts and do not at-

tempt to rivet replacement ball joint to arm.
9. Raise lower control arm and steering knuckle as-

sembly into position, insert upper ball stud into up-

per steering knuckle and install stud nut. Torque

nut as shown in the specifications and insert new

cotter pin. Install stabilizer and strut rod.

10.
Lubricate ball joint, install wheel and tire and re-

move adjustable jackstand.

11.
Lower vehicle and remove upper control arm spacer.

12.
Check and readjust caster and camber angles where

necessary.

LUBE FITTINGS

Special self threading type lube fittings are used in the

spherical joint assemblies. If it is necessary to replace

a fitting a standard threaded type may be used. However,

replacement spherical joint assemblies are supplied less

the lube fitting. Therefore it will be necessary to install

a self threading type fitting into the untapped hole pro-

vided when replacing the entire assembly.

UPPER CONTROL ARM

Chevrolet, Chevelle, Camaro and Corvette

(Fig.
37)

Removal

1.
Support vehicle weight at outer end of lower control

arm.

2.
Remove wheel and tire assembly.

3.
Remove cotter pin and nut from upper control arm

ball stud. ,

4.
REMOVE The stud from knuckle.

5. Remove two nuts retaining upper control arm shaft to

front crossmember. (Chevelle, Camaro and Cor-

vette—Note number of shims at each bolt.)

6. Remove the bolts attaching the control arm to the

frame to allow proper clearance for control arm

removal if necessary.

7. Remove upper control arm from vehicle.

Installation

1.
Install upper control arm in vehicle.

2.
Install nuts, bolts and lock washers retaining upper

control arm shaft to frame. (Chevelle, Camaro and

Corvette—Install same number of shims as removed

at each bolt.)

3.
Torque nuts as shown in the Specifications at the end

of this book.

4.
Install ball stud through knuckle, install nut, tighten

and install cotter pin.

5. Install wheel and tire assembly.

6. Lower vehicle to floor.

7. Bounce front end of vehicle to centralize bushings

and tighten bushing collar bolts as shown in the

Specifications.

Chevy II (Fig. 37)

Removal

1.
Remove spring and shock absorber as outlined above.

2.
Position adjustable jackstand under lower control

arm.

3.
Remove cotter pin and nut from upper ball joint stud

and strike steering knuckle boss to loosen stud.

4.
Drop lower control arm and steering knuckle

assembly.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION
4

REAR SUSPENSION
AND
DRIVE LINE

CONTENTS
OF
THIS SECTION

Page

Rear Suspension
4-1

Drive Line.
. 4-26

Rear Axle ......
4-26
Propeller Shaft
and
Universal Joints

Special Tools
4-37

4-43

REAR SUSPENSION

INDEX

General Description
4-1

Chevrolet
4-1

Chevelle
4-1

Chevy
n and
Camaro
. . . . . 4-2

Corvette
. . . . . . 4-3

Maintenance
and
Adjustments ...............
4-4

Riding Height Check (Chevrolet, Camaro,

Chevelle
and
Chevy
II) 4-5

Wheel Alignment (Corvette)
4-5

Wheel Bearing Adjustment (Corvette)
4-6

Component Parts Replacement (Chevrolet, Camaro,

Chevelle
and
Chevy
JJ) 4-7

Coil Spring
4-7

Chevrolet
4-7

Removal
4-7

Installation
4-7

Chevelle
4-8

Removal
4-8

4-8

Installation
.

Leaf Spring, Spring Seat Pads, Spring
Eye

Bushings
4-9

Chevy
H 4-9

Removal
4-9

Installation
4-9

Camaro
4-10

Removal
4-10

Installation
4-11

Shock Absorber
4-11

Chevrolet
and
Chevelle
. 4-11

Removal
4-11

Installation
. . 4-12

Chevy
II 4-12

Removal
4-12

Installation
4-rl2

Camaro
4-12

Removal
. 4-12

Installation
4-12

Control
Arm . . 4-12

Chevrolet Upper
4-12

Removal
. 4-12
Page

Bushing Replacement
. 4-13

Installation
4-14

Chevrolet Lower
4-14

Removal
4-14

Bushing Replacement
4-14

Installation
. 4-15

Chevelle Upper
and
Lower.
. 4-15

Removal
4-15

Bushing Replacement
4-15

Installation
4-17

Rear Suspension
Tie Rod
(Chevrolet)
. . .
......
. . . 4-17

Removal
4-17

Bushing Replacement
4-17

Installation
4-17

Component Parts Replacement (Corvette)
. . 4-17

Wheel Spindle
and
Support
4-17

Removal
4-17

Repairs
', . 4-17

Installation
4-18

Differential Carrier Support Bracket Replacement.
. 4-20

Shock Absorber
4-20

Removal
4-20

Installation
* .... 4-20

Strut
Rod and
Bracket
4-20

Removal
4-20

Repairs
4-21

Installation
4-21

Spring
4-21

Removal
4-21

Repairs
4-22

Installation
4-22

Torque Control
Arm 4-23

Removal
4-23

Repairs
. 4-23

Installation
4-24

Suspension Crossmember
4-24

Removal
4-24

Repairs—Isolation Mount
4-25

Installation
4-25

Stabilizer Shaft Replacement
4-25

GENERAL DESCRIPTION

CHEVROLET

The link type rear suspension (fig. 1) has two lower

control arms which maintain proper axle to frame re-

lationship and also take the acceleration, drive and

braking forces. A single upper control arm on light-

duty models (or two upper control arms on heavy-duty

models and all station wagons) limits axle rotation when

drive, acceleration or braking forces are applied. Lateral

movement of the axle is restricted by the axle-to-frame

tie rod. Two full coil springs and two direct, double
acting shock absorbers are provided for additional ride

control.

CHEVELLE

The rear suspension (fig. 2) is of the four-link design

utilizing axle mounted, full coil springs and direct,

double-acting shock absorbers.

Two rubber-bushed lower control arms, stretching

slightly outboard from axle-mounted brackets to frame

side member mounted brackets, maintain fore and aft

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE
4-4

PROPELLER SHAFT

CARRIER FRONT SUPPORT
CAMBER CAM CONTROL ARM

Fig. 5—Corvette Rear Suspension and Driveline Components

rubber mounted to the frame at three points, with the .

strut rods, drive shafts and torque control arms forming

the three links at each wheel, and a transversely mounted

multi-leaf spring (fig. 5).

The bbx section trailing torque control arms are

mounted at the forward end into frame side member

openings through pivot bolts and rubber bushings, and

extend rearward to connect to the leaf spring. The

wheel spindles and spindle supports are attached to the

torque arms through four bolts pressed into the arm.

Rear wheel toe-in angle is adjusted through the use of

variable thickness shims inserted between the torque

arm and the frame side member web at the forward

pivoting joint.

The rear wheel spindles are driven through double

"U"
jointed, tubular driveshafts which are flange mount-

ed to a splined spindle flange at their outboard end and

bolted to the differential side gear yokes at their in-

board end. Wheel spindle support houses the inner and

outer tapered roller bearings, two to each wheel. Bear-

ing adjustment is made through the use of a spacer and

variable thickness shims between the bearings.

The spindle supports also incorporate integrally
forged, fork-shaped mounting brackets to accept the

outer ends of the rubber-bushed strut rods. The strut

rods are mounted laterally from the spindle support to

a bracket bolted to the lower surface of the axle car-

rier. The strut rod connection at this point is with an

eccentric cam arrangement and provides for rear wheel

camber adjustment.

The direct, double-acting shock absorbers are at-

tached at the upper eye to a frame bracket and at the

lower eye to the strut rod mounting shaft which incor-

porates a threaded stud for. the shock absorber lower

eye.

The transversely mounted multi-leaf spring is clamp

bolted at the center section to a lower mounting surface

on the differential carrier cover. The outer ends of the

main leaf are provided with a hole through which the

spring is link bolted to the rear of the torque control

arms.
The spring assembly is provided with full length

liners.

An optionally available stabilizer shaft attaches to the

upper rear section of the torque arms, and stretches

rearward where it is connected to the frame by two

rubber-bushed mounting brackets.

MAINTENANCE AND ADJUSTMENTS

Periodic maintenance and adjustments are not required

for the rear suspension components. The suspension

system should be checked for shock absorber action,
condition of suspension bushings, tightness of suspension

attaching bolts and an overall visual inspection of com-

ponents for defects.

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-5

Fig.
6—Measuring Rear Riding Height (Chevrolet and Chevelle)

RIDING HEIGHT CHECK

(Chevrolet, Chevelle Camaro and Chevy II)

In case of vehicle riding height complaints, a spring

height check will show if the rear suspension is at the

right height.

1.
Position car on smooth level floor.

2.
Vehicle must be at curb weight (full gas tank, no

passengers, spare and jack in trunk). Car should be

raised up a few times to allow suspension to settle

with car weight to eliminate friction at arm pivots.

3.
On Chevrolet and Chevelle models, measure riding
Fig.
8—Measuring Rear Riding Height (Camaro)

height as the distance from the top of the axle hous-

ing to frame kick-up (fig. 6).

4.
On Chevy II models, measure riding height as the

distance from lower surface of bumper support

bracket to top of axle housing (fig. 7).

5.
On Camaro models measure riding height as the

distance from jounce bumper upper attaching bolt to

top of axle housing (fig. 8).

6. Riding heights vary between models* Refer to speci-

fications section for vehicle and model application.

WHEEL ALIGNMENT (CORVETTE)

Camber

Wheel camber angle is obtained by adjusting the eccen-

tric cam and bolt assembly located at the inboard mount-

ing of the strut rod (fig. 9). Place rear wheels on

alignment machine and determine camber angle. To

adjust, loosen cam bolt nut and rotate cam and bolt as-

sembly until specified camber is reached. Tighten nut

securely and torque to specifications.

Fig.
7—Rear Riding Height (Chevy II)
Fig.
9—Ad
justing
Rear Wheel Camber (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL