1967 CHEVROLET CAMARO Engine wiring

service reset brake fluid refrigerant type adblue coolant capacity isofix

Page 28 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER AND AIR CONDITIONING 1A-5

them in their proper location. (See Figure 8)

12.
Refill radiator.

Defroster Duct

Figure 9 illustrates the defroster duct installation

on Chevrolet, Chevelle an

HEATER AND AIR CONDITIONING 1A-5

them in their proper location. (See Figure 8)

12.
Refill radiator.

Defroster Duct

Figure 9 illustrates the defroster duct installation

on Chevrolet, Chevelle and Camaro vehicles.

Bowden Cobles

Bowden cable attachment should be made in the fol-

lowing manner:

1.
With the cables attached to the control assembly

and levers, move the levers to their fully left or

closed position.

2.
Attach cable wires to the heater valve levers and

tighten cable attaching bracket screws.

3.
Check for proper cable operation and readjust as

necessary.

Control Panel

Control panel installation is shown in Figures 10, 11,

and 12.

Fan Switch

Replacement

1.
Remove control assembly-to-instrument panel re-

inforcement attaching screws and push the control

assembly toward the front of the vehicle and down.

2.
Remove the two switch attaching screws and the

electrical connector.

3.
Replace switch, screws, and electrical connector.

4.
Place control assembly into instrument panel and

replace attaching screws.

Resistor

The resistor assembly is attached to the heater dis-

tributor assembly. It should "be replaced if low or

medium blower speed is inoperative. Remove the glove

box for access to the unit.
HEATER HOUSING

LOWER RIGHT HAND

RETAINER NUT

Fig.
6—Air Distributor Duct (Camaro)
Fig.
7—Access to Blower and Housing (Chevelle)

CHEVY II

Heater Assembly

Removal (Fig. 13)

1.
Drain radiator.

2.
From within engine compartment;

a. Remove heater hoses from heater inlet and outlet

connections.

b.
Remove three nuts around blower motor attaching

heater assembly to dash panel.

3.
From within vehicle:

a. Remove glove box and glove box door.

b.
Remove screw attaching distributor bracket to

dash.

c. Remove the screw attaching case bracket to the

adapter assembly bracket.

d. Carefully detach heater assembly from dash panel

and adapter assembly and lower it toward floor of

vehicle.

e. Disconnect all bowden cable connections, the

wiring connector and the defroster hoses.

4.
Remove the heater assembly from the vehicle.

Core Replacement

1.
'With the heater assembly removed from the vehicle,

remove the screws attaching the core cover to the

heater assembly.

2.
Remove the core mounting screws and remove the

core from the assembly.

3.
Replace with a new core and replace the core cover.

Installation

1.
Be sure the adapter seal and blower motor seal are

in place and set into place beneath the instrument

panel.

CHEVROLET CHASSIS SERVICE MANUAL

Page 33 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER AND AIR CONDITIONING 1A-10

PLATE RETAINERS

CORE BRACKET SCREWS

Fig.
18—Corvette Heater Core Removal

7. Place a protective covering (waterproof if possible)

over the carpeting under the

Page 36 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER
AND AIR
CONDITIONING
1A-13

AIR CONDITIONING

INDEX

Page

General Description
1A-13

Four-Season System
1A-13

Controls
1A-16

Comfortron System
. 1A-18

System Components
lA-19

Cont

HEATER
AND AIR
CONDITIONING
1A-13

AIR CONDITIONING

INDEX

Page

General Description
1A-13

Four-Season System
1A-13

Controls
1A-16

Comfortron System
. 1A-18

System Components
lA-19

Controls
1A-20

Universal System
. .
1A-21

Chevy
n
All-Weather System
•
1A-21

Corvette Four-Season System
. 1A-22

General Information
. . . 1A-26

Precautions
in
Handling R-12
1A-26

Precautions
in
Handling Refrigerant Lines
1A-28

Maintaining Chemical Stability
in the

Refrigeration System
1A-28

Gauge
Set 1A-29

Charging Station
IA-29

Leak Testing
the
System
1A-29

Vacuum Pump
1A-30

Availability
of
Refrigerant-12
. . 1A-30

Compressor
Oil 1A-31

Compressor Serial Number
1A-31

Inspection
and
Periodic Service
1A-31

Pre-Delivery Inspection
1A-31

6,000 Mile Inspection
1A-32

Periodic Service
, 1A-32

Installing Gauge
Set to
Check System Operation
....
1A-32

Performance Test
1A-32

Performance Data lA-r33

Comfortron System Operational Test
1A-33

Chevrolet Comfortron Tester
1A-34

Complete System Checks
1A-35

Maintenance
and
Adjustments ......
1A-37

Evaporator Comtrol Valve (POA)
.
1A-37
Page

Thermostatic Switch
1A-37

Expansion Valve
1A-41

Engine Idle Compensator
. . .
1A-42

Evacuating
and
Charging Procedures
1A-42

Purging
the
System
1A-42

Evacuating
and
Charging
the
System
1A-43

Checking
Oil . 1A-43

Component Replacement
and
Minor Repair
1A-45

Refrigerant Line Connections
1A-45

Repair
of
Refrigerant Leaks
1A-46

Preparing System
for
Replacement
of

Component Parts
. 1A-46

Foreign Material
in the
System
.
1A-47

Condenser
.
1A-48

Receiver-Dehydrator
1A-48

Evaporator
1A-49

Expansion Valve
1A-57

Evaporator Control Valve (POA)
1A-59

Thermostatic Switch
or
Blower Switch
. .
1A-59

All Weather-Pull Cable
1A-61

Blower Assembly
1A-62

Air Inlet Valve
.
1A-64

Blower
and
Evaporator Assembly
1A-64

Air Distributor Assembly
and
Outlet Ducts ...... 1A-64

Comfortron Automatic Control Components
1A-66

Collision Procedure lA-70

Four-Season Heater Components
1A-73

Comfortron Heater Components
. . . 1A-75

Compressor
1A-76

Wiring Diagrams
1A-78

Special Tools
.
1A-84

GENERAL DESCRIPTION

Four
air
conditioning systems
are
covered
in
this

section. They are:

1.
The
Four-Season System (Chevrolet, Chevelle,

Camaro and Corvette).

2.
The Comfortron System (Chevrolet).

3.
The All Weather System (Chevy n).

4.
The Universal System (Chevrolet, Chevelle, Chevy
n,

Camaro)

Underhood components (that
is, the
compressor,
con-

denser
and
receiver-dehydrator)
are
much
the
same
in

type,
location
and
method
of
attachment
on all of
the

above systems. The six-cylinder reciprocating compres-

sor
is
bracket-mounted
to the
engine
and
belt driven

from
the
crankshaft pulley.
The
condenser
is
mounted

ahead
of the
engine cooling radiator
and the
receiver-

dehydrator
is
mounted
in
the refrigerant line downstream

of
the
condenser.
All
cooling system components
are

connected by means
of
flexible refrigerant lines.

Evaporator size
and
location differ from system
to

system
as do
methods
of
temperature control
and air

supply
and
distribution.

FOUR-SEASON SYSTEM

The Four-Season system used
in the
Chevrolet,

Chevelle, Camaro,
and
Corvette vehicles
may be
iden-

tified
by the
fact that
it
uses
an
evaporator pressure

control known
as the POA
(Pressure Operated Absolute)

suction throttling valve.
Both
the
heating
and
cooling functions
are
performed

by this system.
Air
entering
the
vehicle must pass

through
the
cooling unit (evaporator)
and
through
(or

around)
the
heating unit,
in
that order, and the system
is

thus referred to
as a
''reheat" system.

The evaporator provides maximum cooling
of the air

passing through
the
core when
the air
conditioning sys-

tem
is
calling
for
cooling.
The
control valve acts in the

system only
to
control
the
evaporator pressure
so
that

minimum possible temperature
is
achieved without core

freeze-up.
The
valve
is
preset,
has no
manual con-

trol,
is
automatically altitude compensated,
and non-

repairable.

The heater core will be hot
at
all times since no water

valve
is
present
in
the system.

System operation
is as
follows (See Figure 24 and 25):

Air, either outside
air or
recirculated
air
enters
the

system
and is
forced through
the
system by the blower.

As
the air
passes through
the
evaporator core,
it

receives maximum cooling
if
the
air
conditioning controls

are calling
for
cooling. After leaving
the
evaporator,

the
air
enters
the
Heater
and Air
Conditioner Selector

Duct Assembly where,
by
means
of
manually operated

diverter doors,
it is
caused
to
pass through
or to
bypass

the heater core
in the
proportions necessary
to
provide

the desired outlet temperature. Conditioned airflow then

enters
the
vehicle through either
the
floor distributor

duct
or the
dash outlets. Remember that the heater core

CHEVROLET CHASSIS SERVICE MANUAL

Page 57 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER AND AIR CONDITIONING 1A-34

a. Blower comes on High speed.

b.
Cold air comes from A/C outlets.

3.
Rotate Temperature Dial to 85°F.

a. Blower speed will decrease to Low speed then

increa

HEATER AND AIR CONDITIONING 1A-34

a. Blower comes on High speed.

b.
Cold air comes from A/C outlets.

3.
Rotate Temperature Dial to 85°F.

a. Blower speed will decrease to Low speed then

increase to Medium or High.

b.
Air temperature changes from Cold to Hot and

comes out heater outlet.

4.
Move control lever to LOW Front, with Temperature

Dial at 85°F. Blower operates at Low and Medium

speeds.

5.
Move control lever to Rear, set Temperature Dial

at 65°F.

a. Blower goes to High speed and maintains high

air flow.

b.
All air comes from A/C outlets.

6. Move control lever to DE-FOG.

a. Blower is on Medium or High Speeds.

b.
Air comes from Defroster and Heater Outlets.

7.
Move control lever to DE-ICE.

a. Blower is on High Speed.

b.
Air temperature goes to warm and most of air

comes from defroster nozzle, with small amount

of air coming from heater outlet.

c. Outside air door is open - (door valve is closed

to car body).

8. Move control lever to REAR (dial at 65°). Outside

air door moves outboard. (Door valve is open to

car body).

CHEVROLET COMFORTRON TESTER

The J-22368 Automatic Temperature Control Tester

when in AUTOMATIC position, may be used to perform
Comfortron system checks without disturbing normal car

operation.

Under MANUAL control tester allows the operator to

set and hold a predetermined blower speed
and.
temper-

ature. The tester can also be used to measure external

system voltages by using the probe.

To Install the Tester

1.
Remove the three-terminal male connector from the

Amplifier on the Comfortron control head.

2.
Plug this connector into the three terminal female

connector (with yellow wire)
on
the Tester.

3.
Plug the remaining three-terminal male connector

on the Tester into the Amplifier on the control head.

4.
Attach the black ground lead to any good ground

point available in the car.

5.
Remove the large vacuum hose from Transducer and

connect it to the Tester vacuum hose nipple.

6. Connect the Tester vacuum hose (short hose) to the

Transducer.

Quick Test Procedure

With the J-22368 Tester installed as outlined above,

the following quick checks may be made to pinpoint

the cause of system malfunctions. This quick check

procedure is reproduced on the "swing out" plastic

instruction card attached to the back of the Tester.

Before performing the checking procedure, start the

engine and allow to run on fast idle until operating

temperature is reached. Then set the dash control lever

to HI-FRONT position and the dash control Temperature

Dial to 75° and proceed with the following steps:

Step

1

2

3

4

5A

5B
Tester Settings

Rocker

Switch

Manual

Manual.

Manual

Manual

Manual

Auto-

matic
Voltage

Source

Sensor

Amplifier

or

Control

Cal.

Trans-

ducer

Amplifier

or

Control

Cal.

Amplifier

or

Control

Cal.
Manual

Control

150

150

a. Max.

Heat*

b.
Max.

Cold*

a. Max.

Cold*

b.
Max.

Heat*

Set to

150 for

Comfortron

System

Same as 5A.

Allow 5 min.

for system

to stabilize

with doors

and windows

closed.
Tester Should

Indicate:

Battery Voltage

Battery Voltage

0-4 Volts

8 Volts Min.

8 Volts Min.

0-3 in. Vac.

0-4 Volts

9 in. Min. Vac.

6.5 Volts

5.5 to 7.5 Volts
To Correct Abnormal Indication:

Check fuse and wiring.

Check for open in sensor circuit.

See Service Manual:

Malfunctioning Amplifier or Temperature

Dial.

Check for open or bad ground in trans-

ducer circuit or replace transducer.

Rotate car temperature dial until meter

reads 6.5 volts. Car temperature should

'•- indicate 75°. If not, see temperature

calibration which follows.

After 5 minutes of operation check for

defective sensor.

•This setting should result in HIGH blower speed. Refer to shop manual for further operational checks.

CHEVROLET CHASSIS SERVICE MANUAL

Page 59 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER AND AIR CONDITIONING 1A-36

(These tests should be performed with the engine at operating temperature.)

SYSTEM CHECKS

Control

Head

Setting

High

Front

Lo

Front

Lo

Front

Hi

Front

Hi

HEATER AND AIR CONDITIONING 1A-36

(These tests should be performed with the engine at operating temperature.)

SYSTEM CHECKS

Control

Head

Setting

High

Front

Lo

Front

Lo

Front

Hi

Front

Hi

Front
Tester Settings

Function

Manual

Manual

Manual

Manual

De-ice

65° on

Temp.

Dial

Hi

Front

Hi

Front

Hi

Front
Auto-

Matic

1 1

Auto-

matic

Manual

Manual
Manual

Control

Max.

Heat

Rotate

from

Max.

Heat to

Max.

Cold

150

Max.

Cold

Max.

Cold

Max.

Cold

Max.

Heat

Max.

Heat

Max.

Cold
Voltage

Trans-

ducer

Trans-

ducer

Ampli-

fier

Trans-

ducer

Probe

Probe

Trans-

ducer

Trans.
Tester Should

Indicate:

High Blower

Maximum Heat

Reduced Blower

Speed

Complete series of

blower changes from

Hi to Lo to Hi

again.

AMPLIFIE:

Remove conn, from c

Voltage reading she

Short this lead to grc

Voltage reading she

No voltage change in<

COMPRESSOR C

Cooling System

Operation

DE-ICE i

Assuming rest of

system is operating

normally: Max. Heat

1
to windshield.

SENSOR STR

•—

TRAtfSDtfC

0-3"
Vac. Reading

8 Volts Min.

9"
Min.
Vac.
Reading

0-4 Voltage Reading
If not, check

the following:

Fuse in Slock

In Line Fuse

High Blower

Delay Relay

Duct Delay

Thermistor

High Blower

Delay Sensor

Power Servo

Blower Switch

Resistor

Blower Motor

Wiring Harness

Blower Switch

Master Delay

Thermistor

Master Delay

Relay

Resistor

Power Servo

Blower Motor

CHECK

Resistor

I CHECK
Electrical Diagram

Probe Points:

1-2

8-9

10-21

20

18

19

*
9-46

-r

^2-3
15

16

Checked during

above procedure.

(This is a com-

plete step-by-step

high blower circuit

check which also

checks wiring

harness.)

4

5

6

L2-13

L4

""§2-15

39-46

1
16 1

14

22-40-42-44-15

.ontrol head temperature dial.

>uld be 9 volts minimum,

jund.

>uld be 0 volts,

iicates malfunctioning of amplifier.

JUTCJH CHUCK

Compressor Clutch

(Grille Temp, must

be above 40°.)

IRCUIT

Blower Switch

Master Delay

Relay

Transd

NGCl
ucer

Sensor String

2R CHECK

Transducer voltage

&t Max. Cold

position)

Transducer Ground

Hi Blower Outside

air (air door closed

to car body). Hot air

from heater outlets.

Hi Blower Recirc.

Air (air door open

to car body) cold air

from A/C outlets.
24-25-26-27-28
Voltmete

should re
ad

Battery Voltage

Battery Voltage

Battery Voltage

. Vtinimum
6
volts

Battery Voltage

Minimum
6
volts

Battery Vo]

Batterv Vo]
Ltage

Ltage

Battery Voltage

Batterv Voltage

3a

Bai
:terv Vo

tterv Vo
tage

tage

Minimum
6
volts

Batterv Voltage

Minimum
6
volts

Battery Voltage

Minimum
8
volts

Minimum 8 volts

Minimum 8 volts

Batterv Voltage

Minimum 8 volts

1 III • II »ll. —..• —•— . !!•• 1

Battery Voltage

3-23

20-10-21

38

29-30-31-32-33-

34-35-36

37-38

Defective Power Servo; Leak in Vacuum

System; Temp.; Door Link Disconnected

or Jammed; Defective Vacuum Relay

Valve

Defective Mode Door Diaphragm
Batterv Voltage

Battery Voltage

Zero Voltage

Battery Voltage

Battery Voltage

CHEVROLET CHASSIS SERVICE MANUAL

Page 76 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER AND AIR CONDITIONING 1A-53

Fig.
70—Wiring and Vacuum Lines—Four-Season (Camaro)

Installation

1.
Connect the expansion valve to the refrigerant pipes.

Attach the capillary bulb to the

HEATER AND AIR CONDITIONING 1A-53

Fig.
70—Wiring and Vacuum Lines—Four-Season (Camaro)

Installation

1.
Connect the expansion valve to the refrigerant pipes.

Attach the capillary bulb to the evaporator.

2.
Attach the evaporator to the- case. Attach the inlet

and outlet pipes clamps.

3.
Assemble the case halves. Insert the capillary tube

from the thermostatic switch between the fins as

shown in Figure . Attach the cover plate to the

case.

4.
Mount the unit to the dash and connect the refrigerant

lines.

5.
Evacuate and charge the system. If a new evaporator

was installed, add three fluid ounces of refrigerant

oil to the system before charging.

6. Test system operation.

Chevy II All-Weather System

Removal

Under
the Hood

1.
Purge the refrigerant from the system.

2.
Remove the refrigerant hoses from the evaporator

inlet and outlet connections extending through the

special grommet in the dash panel and into the

engine compartment.

3.
Remove the screw, nut, spacer bracket and grommet

from the outlet connection pipes.
Within the Car

4.
Remove the glove box, ash tray and ash tray

retainer.

5.
Reach through the glove box door to disconnect the

air conditioning "on" door bowden cable (fig. 75).

6. Remove the two shield attaching screws and shield

(A, fig. 76) which covers the lower right evaporator

bracket-to-blower bracket attaching screw (B, fig.

76),
then remove this screw.

7.
Behind the lower left side of ihe evaporator, remove

the evaporator bracket-to-heater distributor bracket

attaching screw (C, fig. 76).

8. Reaching through the glove box door and ash tray

openings, remove the two nuts and washers (D,

fig.
76) attaching the evaporator assembly studs to

the lower instrument panel flange and reinforcement.

9. Disconnect the drain hoses and carefully pull the

evaporator unit toward the rear of the vehicle.

10.
Disconnect wiring connectors (see fig. 77) as nec-

essary and remove the evaporator unit from the

vehicle.

Gore and/or Expansion Valve Replacement

A defective unit must be replaced since repairs should

never be made on the evaporator core. Before replacing

the core, however, check to be sure that any leaks pres-

sent are not located at the hose connections or expansion

valve connections. The following procedure assumes that

the evaporator unit has been removed from the vehicle

as outlined above.

CHEVROLET CHASSIS SERVICE MANUAL

Page 79 of 659

$CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual HEATER AND AIR CONDITIONING 1A-56 BLACK & RED IGNITION—-y^**** SWITCH -"A /<J 7 BLOWER LEAD—^^^ RESISTOR—-" \^< ASM. f i fu^^^^A^^^^^r"G^OUH£> WIRE ^^ k4 ^EVAPORATOR HARNESS$

Page 87 of 659

CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual
HEATER AND AIR CONDITIONING 1A-64

Fig.
90—Evaporator Wiring (Corvette)

AIR INLET VALVE

Four-Season System

Chevrolet

Figure 88 illustrates the vacuum valve which controls

the air inlet operat

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 33-40 ... 40 next >

bulb check oil climate control ESP fuse box diagram