1953 JEEP DJ Service Manual

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H
cuit
lights,
the
signal switch
is
inoperative
and

must
be
replaced.

H-139.
Hazard
Warning Lights

All
current production vehicles
are
equipped with

a
four-way flasher warning system.
The
control switch
is
located
on the
instrument panel left
of

the steering column.
With
the
switch pulled
out,
the
two
front and
two
rear
turn
signal lights flash
on and
off
simultaneously,
as do
both
turn
signal

indicator
lights
on the
instrument clusters.
H-140.
Marker
Lights and Reflector Assembly

The
marker
lights
and
reflector assemblies
on

current
production vehicles
are
mounted
on the

side
of
the front fender and
on the
side
of
the
rear
quarter
panel.
The
spare wheel also mounts
a

marker
light. Some earlier production vehicles have
reflex reflectors mounted on the side of the hood and
on
the
side
of
the
rear
quarter panel. determine
if
dash wiper switch or wiring
is at
fault,
disconnect wiring harness from wiper motor
and

try
operating wiper independently
of
dash switch.
If
still
inoperative
see
procedure under
Par.
H-145.
b. Wiper
will
not
shut
off
— Determine
if
wiper
has both
low
and high speeds, slow speed only,
or

high speed only.
It is
important that
the
wiper
operates
at low
speed during parking cycle.
Dis­
connect wiring harness from wiper motor
and try

operating wiper independently
of
dash switch.
If

wiper
shuts
off
correctly with
crank
arm
in
park
position and wiper has both speeds, check
the
lead

between
terminal
and
dash switch ground
and

check
for
defective dash switch.
If
wiper shuts
off

correctly,
but has
high speed only, check lead
be­

tween wiper terminal and dash switch
for an
open

circuit
and check
for
defective dash switch.
If
still

inoperative,
see
Par. H-145.
c. Wiper
has
only fast speed.
Check
for
defective dash switch
or
open lead
between
terminal
and

dash switch.

H-141.
Windshield Wiper System

Early
production vehicles equipped with
the
Dauntless V-6
engine
have
two
single speed wind­
shield wiper motors mounted above
the
windshield inside
the
vehicle. The wiper motors
are
operated

and
controlled
by a
switch located
on the
instru­
ment panel.

Current
production vehicles with stationary wind­
shield have
a
two-speed
electric windshield wiper motor mounted below
the
windshield outside
the

vehicle on the driver's side. The wiper motor switch is located
on the
instrument panel
to the
left
of

the steering column.

H-142.
Two-Speed Wiper Motor

The
two-speed
electric wiper motor
is
operated and
controlled
by a
turn
type, three poled, dash switch,
containing
a 6
amp. circuit breaker.
Current
flow
is directed from
the
battery through
the
ignition
switch
to the
wiper dash switch assembly
to the

two-speed
wiper motor, which passes current from the designated motor brush (high,
low or
park)
to

the armature circuit
to
ground.

H-143.
Troubleshooting Procedure
Troubleshooting procedures
are
divided into
two

categories: wiper troubleshooting
in
vehicle; wiper
troubleshooting
on
bench.
Fig. H-65 and H-66

illustrates connecting leads
of the
two-speed
wiper for either bench operation
or to run
wiper inde­
pendently
of
dash switch and vehicle wiring when
installed
in the
vehicle.
H-144. Wiper Troubleshooting
in
Vehicle

Typical
wiper troubles and remedies are
as
follows
:

a.
Wiper
is
inoperative
—
Check
wiper switch
cir­

cuit
breaker; wiring harness connection
at
wiper
motor
and
wiper switch; wiper motor
feed
wire

from
ignition starter switch
to
wiper switch;
and
check wiper
on
switch
to be
securely mounted.

With
ignition switch
on,
check
for 12
volts
at
har­

ness
terminal that connects
to
wiper terminal.
To
BLACK
PARK

GREEN *-
RED m~
LOW
PARKING
<^^>

SWITCH
V^-O*'
HIGH

FIG.
H-64—WIRING
DIAGRAM

FIG.
H-65—WINDSHIELD
WIPER
SWITCH
ASSEMBLY
(EARLY)
1.
Park
(black)
2. Low (green)

3.
High (red)
d.
Wiper
has
only slow speed
and
shuts
off
with
dash switch in high speed position. Reverse harness
leads that connect
to
wiper terminals.

e. If
blades
do not
return
to
park
position when

wiper
is
turned
off,
check wiper ground connection
to vehicle body. Remove wiper from vehicle
and

check
for
dirty, bent,
or
broken
park
switch con­
tacts.

f.
If
wiper speed
is
normal
in
slow,
but too ex­
cessive
in
fast speed, check for an open terminal. 217

ELECTRICAL
SYSTEM

FIG.
H-66—WINDSHIELD
WIPER SWITCH ASSEMBLY (LATE)
B—Battery

1—
Wiper
1 La
Speed
2—
Wiper
1 Hi
Speed

3—
Wiper
2 Lo
Speed

4—Wiper
2 Hi
Speed
5— Park
g. If wiper operates erratically, check for
loose

wiper
ground connection or
loose
dash switch mounting.

H-145.
Wiper Troubleshooting on Bench

Using
ammeter, capable of reading at least 30
amperes, check
feed
wire circuit for open circuit.

a.
If wiper is inoperative, connect wiper to operate
in
low speed and observe current draw. If the read­
ing is zero amp., check for
loose
solder connection
at wiper terminal or
loose
splice joints. If reading is
1
to 1.5 amp., check for open armature, sticking
brushes, or
loose
splice joint. If reading is 11 amp.,
check for broken gear seized shaft or
some
other
condition that
will
stall the wiper.
b. If wiper
will
not shut off, this condition may
exist if wiper has one or both speeds. If wiper has both speeds, check for
park
switch contacts not
opening or internal wiper motor lead that connects to wiper terminal being grounded. If wiper has low
speed only, check for internal wiper motor lead that connects to wiper terminal being grounded. If

wiper
has high speed only, check for
internal
wiper motor lead that connects to wiper terminal being
open.

c.
If wiper
crank
arm
does
not return to
park

position when wiper is turned off, check for dirty, bent to broken
park
switch contacts.

d.
If wiper operates erratically, check for sticky
brushes or
loose
splice joints.
e. If the wiper
will
not shut off, or wiper
crank
arm
fails to
stop
in
park
position when jumper wire is
removed from terminal, check that
park
switch contacts are opening. Also check for ground in in­

ternal
motor lead that connects to terminal.
f-
Remove fastening screws, cover plate assembly

and
gasket.
g. Remove parking plate and gear assembly.

h.
Remove parking brushes, spring and bowed
washer from gear assembly.

i.
Remove the two through
bolts
and mounting

bracket.

j.
Remove the magnet housing, armature and end cap as an assembly.

k.
Tap end of armature shaft to
loosen
end cap
assembly and remove cap from armature shaft. Be
careful
not to
lose
thrust disc, which is in end cap
bearing bore.

I.
Remove armature from magnet housing.
Care

should be taken to protect armature shaft bearing

journals.

m.
Remove brushes and brush spring from brush
holders.

H-147.
Cleaning
of
Two-Speed
Wiper
Motor

a.
Clean
magnet housing and
armature
with a cloth dampened in cleaning solvent.

b.
The following bearing equipped parts should

not
be immersed in cleaning fluid: 1. Cover plate assembly.
2.
Gear
housing assembly.

3.
End cap assembly.

The
metal surfaces of
these
assemblies should be cleaned with a brush dipped in cleaning solvent,

making
certain that cleaning fluid
does
not contact bearings.

c.
Clean
remaining parts with a brush and cleaning
solvent.

H-148.
Reassembly
of
Two-Speed
Wiper
Motor

Refer
to Fig. H-67.
To
reassemble motor, reverse the
steps
given in

Par.
H-146.
When
reassembling motor, fingers must be clean
when handling brushes. Hold brushes in the holders by applying paper clips to brush shunts. Apply a
light film of lubricant to armature shaft ends,
armature
worm gear and gear assembly shaft ends.
Remove paper clips after assembling armature to gear housing. Align marks on magnet housing and
gear housing. Armature end play should be .002 -
.010".

Be
sure to operate wiper to
park
position prior to installing drive arm.

H-146.
Disassembly
of
Two-Speed Wiper Motor

Refer
to Fig. H-67.

a.
Remove windshield wiper motor cover.
b.
Disconnect drive arm from wiper linkage.

c.
Disconnect wiring from wiper dash switch.

d.
Remove wiper motor.

e.
Loosen drive arm hardware and pry drive off
drive
shaft.
H-149.
No
Load
Testing

Test
the motor to
meet
the following specifications:

LOW SPEED HIGH SPEED

Ampere Ampere

Draw Draw

R.P.M.
(Max.)
R.P.M.
(Max.)
42 2.75 62 3.75 218

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H

a
0"—®
FIG.
H-67—-TWO-SPEED
WIPER
MOTOR

1—
Brush,
Commutator — Grounded - includes Terminal

2—
Spring,
brush — Commutator
3—
Insulation
Grommet, Cable

4—
Nut,
Locking
— Set Screw
5— Screw, Set — armature End Play
6—
Bearing,
Gear
Shaft
7—
Spring,
Parking Brush 8—
Brush,
Parking
9—
Nut
& Lockwasher,
Drive
Arm

10—
Screw, Securing —
Drive
Arm

11—
Arm,
Drive

12—
Screw, Fastening — Mounting
Plate

13—
Gasket,
Mounting
Plate

14—
Plate
Assembly, Parking

15—
Washer, Bowed
16—
Gear
Assembly

17—
Brush,
Commutator — Insulated

18—
Armature
Assembly

19—
Thru
Bolt,
Fastening — Motor Assembly

20—
Cap Assembly, End — includes Bearing

21—
Disc,
Thrust H-150. Major
Electrical
Component
Replacement

•
Prestolite and Delco-Remy Components

a.
Some
Prestolite and Delco-Remy electrical
components may be intermixed on a vehicle as an
approved production practice. No attempt should
be
made
to convert to a complete Prestolite or Delco-Remy system. Prestolite components should
be replaced by Prestolite components and Delco- Remy components should be replaced by Delco-
Remy components insofar as
availability
of re­ placement components
will
allow.
In
those
cases,

however, where a component is being replaced
with

one produced by the other manufacturer, make
certain factory approved service instructions are

followed
during
these
installations.
b. Distributor — No special instructions are re­

quired
for interchanging Prestolite and Delco-
Remy distributors on V6 models.
c. Starting Motor — Special instructions are re­
quired
for interchanging Prestolite and Delco-
Remy starting motors. See note
following
Par.
H-108. 219

H

ELECTRICAL
SYSTEM H-15L SERVICE
DIAGNOSIS

SYMPTOMS

Battery
Discha
rged: Shorted
Cell
in Battery......... Short in Wiring..
•
Generator Not Charging ,
Loose or Dirty Terminals
Excessive Use of Starter Excessive Use of Lights...... Insufficient Driving.........

Low
Regulator
Setting.......

Stuck
Cut-out in Regulator. ..

Low
Electrolyte
Level
in Cells

Alternator:
FAILS
TO
CHARGE:
Belt Loose Open or High Resistance in

Charging
or Ground Return
Circuit
or Battery Connections............
Excessively Worn, Open, or
Defective
Brushes.
Open Isolation
Diode.

Open Rotor (Field
Coil)

LOW
OR
UNSTEADY
CHARGING RATE:
Belt Loose.... Intermittent or High Resistance
Charging
or Ground Return
Circuit
or Battery Connections
Excessively Worn, Sticky, or Intermittent Brushes
Shorted or Open Rectifier
Diode
Grounded
or Shorted
Turns
in Rotor (Field
Coil)

Open,
Grounded, or Shorted
Turns
in
Stator

EXCESSIVE
CHARGE RATE:
Loose Connections on Alternator...........

Faulty
Regulator

NOISY
ALTERNATOR:
Defective
or Badly Worn Belt
Misaligned Belt or Pulley
Loose Pulley
Worn
Bearings.
Shorted Rectifiers

Generator:
Low
Charging Rate—
Dirty
Commutator
Poor Brush Contact.
................
Regulator Improperly Adjusted.......

High
Resistance in Charging
Circuit...
Ground
Strap Engine to Frame Broken
Loose or Dirty Terminals Slipping Generator Belt

Worn
Out Brushes

Weak
Brush Spring Tension..........

Out
of Round Commutator
PROBABLE REMEDY

Replace Battery

Check
Wiring
Circuit

Inspect Generator and Fan Belt
Clean
and Tighten

Tune
Engine

Check
Battery
Recharge Battery
Correct
Setting

Correct
Add
Distilled Water
Tighten to
Specifications
Test
and Correct
Test
Brushes and Replace if Necessary

Test
and Replace if Necessary
Test
and Replace if Necessary
Tighten to
Specifications

Test
and Correct
Test
and Replace if Necessary
Test
and Replace if Necessary

Test
and Replace if Necessary

Test
and Replace if Necessary

Check
and Correct

Check
and Correct
Replace

Align,
Replace Parts as Necessary Tighten Replace Bearings as Necessary
Test
and Replace as Necessary

Clean
Commutator
Repair
or Install New Brushes

Adjust

Clean
and Tighten Terminals Replace

Clean
and Tighten

Adjust
Belt
Install
New Brushes
Replace
Repair
220

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

H
H-151.
SERVICE
DIAGNOSIS—Continued

SYMPTOMS PROBABLE
REMEDY

Generator:
(continued)
Fails
To Charge-Open Charging Circuit Correct
Sticking Brushes Repair or Replace
Dirty
or Burned Commutator ... Clean Commutator
Grounded Commutator Replace
Open Circuit in Field Replace
Weak Soldering on Armature. . . Repair Grounded Wiring Repair

Defective
Regulator. .. Replace Regulator
Too High Charging Rate— Regulator Improperly Adjusted Adjust or Replace
Short in Armature Replace Grounded Field-to-regulator Wire Correct
Shorted
Cell
in Battery... Replace Battery

Starting
Motor: Slow Starter Speed— Discharged Battery or Shorted
Cell
Recharge or Repair
Ground
Strap Engine to Frame. Clean Terminals and Tighten
Loose or Dirty Terminals Clean and Tighten
Dirty
Commutator Clean with No. 00 Sandpaper

Worn
Out Brushes Install New Brushes
Weak Brush Spring Tension Replace

Worn
Bearings Replace Burned Starter Switch Contacts Replace Switch

Will
Not
Turn
Engine— Open Circuit at Starter Correct

Solenoid
Open or Stuck Replace
Solenoid
Starter Switch
Defective
Replace Switch
Starter Drive Broken or Stuck. Repair or Replace
Battery Discharged Recharge Battery

Distributor:
Hard
Starting— Distributor
Points
Burned or Pitted Clean
Points
or Replace (Adjust)

Breaker
Arm Stuck on Pivot Pin...... . ... . . . Clean and Lubricate

Breaker
Arm Spring Weak Replace

Points
Improperly Adjusted Adjust
Spark
Plug
Points
Improperly Set Adjust

Spark
Plug Wire Terminals in Distributor
Cap
Corroded Clean
Loose Terminals Check Circuit
Loose or Dirty Terminals on Ground Strap— Engine to Frame. Clean and Tighten
Condenser Faulty Replace Improper Ignition Timing Set Timing

Lights:
Burn
Dim— Loose or Dirty Terminals....... ........ Clean and Tighten
Leak
in Wires. Check Entire Circuit for Broken Insulation
Poor Switch Contact Install New Switch Poor Ground Connection Clean and Tighten

Aim
Headlamp Beams. Use Aiming
Chart
221

H

ELECTRICAL
SYSTEM
H-151.
SERVICE
DIAGNOSIS—Continued

SYMPTOMS
PROBABLE REMEDY

Horn
Fails
to Sound:
Broken
or Loose
Electrical
Connection Check Wiring and Connections at Horn Button and
Battery—Clean
and Tighten
Battery Low or Dead Check Battery Contact Points Burned or Broken Off. Replace Parts Necessary

Horn
Sounds Unsatisfactory Tone: Poor
Electrical
Connection Check Connections at Horn, Horn Button, Battery Battery Low Check with Hydrometer Loose Cover and Bracket Screws Tighten Bracket Bolts at Horn
Voltage at Horn too High or too Low Check with Voltmeter 222

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

H
H-152.
ELECTRICAL
SPECIFICATIONS
MODEL HURRICANE
F4 ENGINE DAUNTLESS
V-6
ENGINE

BATTERY:
Make
Model Hour Rating.

Voltage
Terminal
Ground

SPECIFIC
GRAVITY:
Fully
Charged
Recharged At
Location

GENERATOR:
Make.
Model

Ground
Polarity
Controlled Output

Control

Armature End Play
Brushes

Brush
Spring Tension

REGULATOR:
Make
Model:
For
GJP
7202,
GJP
7402A

Type
Cutout Relay: Closing
Voltage
@
Generator rpm..........
Reverse Current to Open.
Regulated
Voltage

Regulated Current

ALTERNATOR:
Make
Model
Ground
Polarity
Rated Output
Rated Field
Coil
Draw

At
70°F.
and
10-volt

Capacitor Capacity

REGULATOR:
Make
Model
Type

STARTING
MOTOR:
Make
Model
Brush
Spring Tension

LOCK
TEST:
Temperature
Amp.
(Max.)
Volt
Stall
Torque (Min.)

NO LOAD TEST:
Tempesature

Amp.
(Max.)
Volt
Rpm.
(Min.)

DRIVE:
Type

COIL:
Make.
Model

Primary
Resistance Secondary Resistance
Prestolite

HS
11-50
50 Ampere-hour
12-volts

Negative

1.260
1.225
Engine Compartment- Right Rear

Prestolite

GJP-7402A
Negative
35 amp.

CV
Regulator .003" to .010"

[0,076
a 0,25 mm.] 2
18 to 36 oz.
[510 a 1020 gr.]

Prestolite

VBO-4201E-4A
Vibrator

12.6 to 13.6 @ 1325 3 to 5 amp. 14.2 to 14.4
36 amp. max.
Motorola
A12 NW 526
Negative
35 amp.
1.7 to 2.3 amp. .1 mfd.
Motorola
R-2-K-1

Transistor

Prestolite

MDU-7004
32 to 40 oz. [907 a 1134 gr.]

70°F.
[21°C] 295 4
6 lb-ft. [0,83
kg-m.]

70°F.
[21°C.;
50
10

5300

Bendix Folo-Thru
Prestolite
200691

3.9 to 4.2
ohms

9400
to
11,700
ohms
Prestolite

HS
11-50
50 Ampere-hour
12-volts

Negative

1.260
1.225
Engine Compartment- Right Rear

Prestolite

GJP-7402A
Negative
35 amp.

CV
Regulator .003" to .010"

[0,076
a 0,25 mm.] 2
18 to 36 oz.
[510 a 1020 gr.]

Prestolite

VBO-4201E-4A
Vibrator

12.6 to 13.6 @ 1325 3 to 5 amp. 14.2 to 14.4
36 amp. max.
Motorola
A12 NW 528
Negative
35 amp.
1.7 to 2.3 amp. .1 mfd.
Motorola
R-2-K-1

Transistor
Delco-Remy

1107391,
1108366,
1108375

32 to 40 oz. [907 a 1134 gr.]
Not Applicable Not Applicable

70°F.
[21°C] 75
10.6

6200

Overrunning Clutch Delco-Remy
1115247

1.28 to 1.42
ohms

7200
to
9500
ohms
Prestolite

MHA-7008
32 to 40 oz. [907 a 1134 gr.]

70°F.
[21°C] 200 4
3 lb-ft. [0,41
kg-m.]

70°F.
[21°C] 43
10.0

9000

Bendix Folo-Thru

Prestolite
201700

4.25 to 4.60
ohms

5200
to 6100
ohms
223

H

ELECTRICAL
SYSTEM
H-152.
ELECTRICAL
SPECIFICATIONS—Continued

HURRICANE DAUNTLESS
V-6
DAUNTLESS
V-6 ENGINE
MODEL -
F4
ENGINE
ENGINE
LATE
MODELS

EARLY
MODELS
IGNITION
COIL
BALLAST
]Make Delco-Remy
Prestolite Prestolite
Model
None

1957154

PU
5003

PU
5003

Ohms • • 1.80 @
80°F.

.495 - .605 @
75°F.

.495 - .605 @
75°F.

1.80 @
80°F.

.638 - .835 @
212°F.
.638 - .835 @
212°F.

DISTRIBUTOR:
Prestolite Delco-Remy Prestolite Prestolite
Model
•
(a)
LAY
4012, 4401

1110376

I
AT
4501 or
IAT
4502A
(b)
I
AY
4401A, 44011

IAT
4502

Breaker
Point Gap (b)
.020"
[0,508
mm.] .016"
[0,406
mm.] .016"
[0,406
mm.]
.016"
[0,406
mm.]

Breaker
Arm Tension. ..... 17 to 20 oz.
19 to 23 oz. 17 to 22 oz. 17 to 22 oz.
[482 a 567 gr.] [538 a 652 gr.] [482 a 624 gr.]
[482 a 624 gr.]

42° 29°
to 31°
29°
±3°
29°
±3°

Max.
Auto Advance
(Crankshaft
Degrees) •(a)
11°
@ 1,700 rpm.

13°
to
15°
at 1,950 rpm.
16°
@ 1,800 rpm.
21°
(2 1,800 rpm.

(Crankshaft
Degrees)
(b)
13.5°
@ 1,700 rpm.

26°
@
4200
rpm.
32°
@
4200
rpm.

Max.
Vac. Advance go
(Distributor Degrees)., . .
None

8° 8°
go
Condenser Capacity. . .25 to .28 mfd. .18 to .23 mfd. .25 to .28 mfd. .25 to .28 mfd.

TIMING:
Crankshaft
See
Note

See
Note
See
Note
See
Note

Mark
Location............
Crankshaft
Pulley

Crankshaft
Pulley

Crankshaft
Pulley

Csankshaft
Pulley

Firing
Order
1-3-4-2

1-6-5-4-3-2
1-6-5-4-3-2 1-6-5-4-3-2

SPARK PLUGS:
Make
Champion

A.C. A.C.
or Champion
A.C.
or Champion

J8
44S
44S or UJ 12Y 44S or UJ 12Y

Thread
14 mm.
14 mm. 14 mm. 14 mm.

Thread
Reach
Vz"
[9,47 mm.]
%"
[9,47 mm.]

¥%"
[9,47 mm.]
V8" [9,47 mm.]

Gap
.030"
[0,762
mm.]
.035"
[0,900
mm.] .035"
[0,900
mm.] .035"
[0,900
mm.|

LAMP BULB TRADE
NUMBERS:

Headlight 6012
6012 6012 6012

Parking
and Directional Signals. 1157NA
1157NA 1157NA 1157NA

License
Plate Light........ 1155
1155 1155 1155

Marker
and Reflector 194
194 194 194

INDICATOR LIGHTS:
57 57 57 57
Directional Signals........ 57
57 57 57

Charge
57
57 57 57
57 57 57 57
1156 1156 1156 1156
Instrument Cluster 57 57 57 57

Warning
— 4 Way Flasher. . 57
57 57 57

Brake
Warning Light 57
57 57 57

FUSE
DATA:
Heater 9 amp. 9 amp. 9 amp. 9 amp.

Backup
14 amp. 14 amp. 14 amp. 14 amp.

WS/Wiper.
14 amp. 14 amp. 14 amp. 14 amp.
Directional Signal 9 amp. 9 amp. 9 amp. 9 amp.
4-Way Flasher 14 amp. 14 amp. 14 amp. 14 amp.

Brake
Warning Light 9 amp. 9 amp. 9 map. 9 amp.

FLASHER
DATA:
Directional Signals. 144
144 144 144

Hazzard
Warning. 170
170 170 170

NOTE:
0°
T.D.C.
on Distributor
models
IAY 4401A, IAY 4401B, IAT 4502A.

NOTE:
5°
B.T.C.
on Distributor
models
IAY 4012, IAY 4401, IAT 4501, IAT 4502,
1110376.
224