1953 JEEP DJ battery capacity

H

ELECTRICAL
SYSTEM

ffKHs)

3—<§)

FIG.
H-7—WIRING
DIAGRAM—V6
ENGINE
CURRENT
MODEL
1—
Left
Headlamp
2—Left Parking and Signal Lamp
3— Right Parking and Signal Lamp
4—Right Headlamp 5—
Marker
Lamp — Amber
6— Alternator 7— Voltage Regulator
8— Starting Motor
9— Battery Ground Cable
10— 12 Volt Battery
11—
Flasher
(Directional Signal)
12— Instrument Cluster
A—Hi-Beam
Indicator
B—Auxiliary

C—Instrument
Lights

D—Oil
Pressure Indicator
E—Charging
Indicator

F—Temperature
Indicator

G—Fuel
Gauge Indicator
H—Instrument Voltage Regulator
13— Ignition and Starter Switch
14—
Horn
Button
15— Directional Signal Switch
16— 4-Way Flasher Switch 17—
Flasher
(4-Way)
18— Windshield Wiper Motor Switch
19—
Main
Light Switch
20—
Fuel
Gauge
Tank
Unit
21—
Back-Up
Light Switch
22—
Marker
Lamp — Red
23— Right
Tail
and
Stop
Light 24— Right Back-Up Lamp
25—
Left
Back-Up Lamp 26—
Left
Tail
and
Stop
Light
27—
Marker
Lamp — Red
28—
Stop
Light Switch
29— Foot Dimmer Switch
30— Windshield Wiper Motor Assembly
31—
Ballast
Resistor 32— Ignition
Coil

33—
Spark
Plugs and Cables 34— Temperature Sending Unit
35—
Oil
Pressure Sending Unit 36—
Horn
37— Junction Block
38—
Marker
Lamp — Amber

lions
on the terminal
posts.
Be sure
condenser
is
mounted
firmly on the distributor for a
good
ground
connection.

Should a
condenser
tester
be available the capacity for
both
F4 and Prestolite V6
condenser
should
check from .25 to .28 microfarads. In the
absence

of
tester,
check by substituting a new
condenser.

H-13. Distributor Points
a. Examine the distributor
points.
If
they
show

wear,
poor
mating, transferred metal, or pitting,

then
new
ones
should be installed. Clean the
points

with a suitable
solvent
and a stiff bristled brush.
b. Check the
alignment
of the
point
for a full,
square
contact.
If not correctly aligned, bend the
stationary
contact
bracket slightly to provide align­
ment.

c. The
contact
gap should be set at .020"
[0,508
mm.],
on the F4 and .016"
[0,406
mm.] on the
Prestolite V6. Adjustment of the gap is accom­ plished by
loosening
the lock screw and turning adjusting eccentric screw until correct gap is
secured. Be sure that the fiber block on the breaker

arm
is resting on the
highest
point
on the cam while the adjustment is
being
made. Recheck the gap
after locking the adjustment.
d. Apply a thin film of cam lubricant to the cam to
lessen
fiber block wear.
e. Using Tool C-4094, check
point
contact
spring
pressure, which should be
between
17 and 20

ounces
[0,487
a
0,567
kg.] on the F4 and 17 to 22 oz.
[0,487
a
0,624
kg.] on the Prestolite V6.

Check
with a spring scale
hooked
on the breaker

arm
at the
contact
and pull at right
angle
to the
breaker arm. Make the reading just as the
points

separate. Adjust the
point
pressure by
loosening
the stud holding the end of the
contact
arm spring
and slide the end of the spring in or out as
neces­

sary.
Retighten the stud and recheck the pressure. Too low a- pressure will
cause
engine
missing at
high
speeds.
Too high a pressure will
cause
rapid
wear of the cam, block, and
points.
180

H

ELECTRICAL
SYSTEM
colder plug may be desirable. However, under- or
over-heating is usually caused by factors other than the type of
spark
plugs and the cause should be determined before changing plugs. The design of the
engine
calls for plugs equivalent to Champion

J-8
for F4
engines
and
A.C.
44S or
UJ12Y
Champ­

ion for the V6 engines, (as installed in production)
though any factor that consistently affects
engine
operating temperature may cause this requirement
to change. Overheating may be caused by in­ sufficient tightening of the plug in the head, which interferes with the flow of heat away from the firing

tip.
If this is the case, the plug gasket
will
show very
little flattening. Over-tightening, in
turn,
will
pro­ duce too easy a heat flow path and result in cold
plug operation.
This
will
be evident by excessive
flattening
and
deformation of the gasket.
Prevailing
temperatures, condition of the cooling system, and

air-fuel
mixture can affect the
engine
operating temperature and should be taken into consideration.
H-34.
GENERATOR
— F4
ENGINE

The
generator is an air-cooled, two-brush unit

which
cannot be adjusted to increase or decrease output. For replacement,
voltage
regulator and generator must be matched for
voltage
and capa­

city,
polarity, and common source of manufacture.
Otherwise,
either a
loss
of ampere capacity or a

burned
out generator
will
result. Generators for

these
vehicles are 12-volt. Par. H-l explains the 12-volt system. Refer to the specifications at the
end of this section for information on correct generator rating for a specific model series.
The
circuit
breaker,
voltage
regulator, and current-

limiting
regulator are built into one combination

unit.
Because the regulator and battery are part
of the generator
circuit,
the output of the generator
depends upon the
state
of charge and temperature
of the battery.
With
a discharged battery, the
output
will
be high, decreasing proportionally as the battery
becomes
charged. For service informa­
tion covering current regulator see Par. H-41.

H-36.
Generator
Maintenance

A
periodic inspection should be made of the charg­
ing
circuit,
Fig. H-l9. The interval
between
these
checks
will
vary
depending upon type of service.
Dust,
dirt
and high speed operation are factors 10541

FIG.
H-19—CHARGING
CIRCUIT

1—
Battery
4-—Starter Switch

2—
Voltage
Regulator 5-—Charge Indicator

3—
Generator
which
contribute to increased wear of bearings

and
brushes.

Under
normal conditions a check should be made
each 6000 miles
[9.600
km.].

A
visual inspection should be made of all wiring,
to be sure there are no broken or damaged wires.

Check
all connections to be sure they are tight and

clean.

Should
the commutator be rough or worn the
armature
should be removed and the commutator

turned
and undercut. See Par. H-37.
The
brushes should slide freely in their holders.

Should
they be oil soaked or if they are worn to

less
than one-half their original length they should
be replaced. When new brushes are installed they should be sanded to provide
full
contact with the
commutator. Generators should not be checked for
output until the brushes are seated.

Brush
spring tension is important. High tension causes
rapid
brush and commutator wear while
low tension causes arcing and reduced output.
Test
the tension with a spring scale.
Check
the
specifications section at end of this section for

correct
spring tension for generator in question.
H-36.
Generator Disassembly
•
Refer to Fig. H-20:
Before beginning disassembly of the generator to

correct
electrical system malfunctions proceed with
inspection and
test
procedures as detailed in Par.

H-46
thru
H-62. If it is definitely determined that trouble exists within the generator, which ne­cessitates dismantling, proceed as follows. Remove the two frame screws in the commutator
end plate and remove the end plate assembly. Next
pull
the armature and drive head complete

from
the generator housing. Remove the generator pulley from the armature by removing the nut

and
washer. Do not
lose
the Woodruff key when
the pulley is removed. After this, remove the drive
end head assembly which includes the oil seal and
bearing.
To remove the bearing, remove the three
screws and lockwashers in the grease retainer and remove the retainer and felt washer, after which,
remove the bearing, oil guard and felt washer.
H-37.
Armature

If
the commutator is rough or worn,
turn
it down

in
a lathe. After turning, the mica insulation be­ tween the
segments
should be undercut to a depth of 34* [0,8 mm.].
To
test
the armature for a ground, connect one

prod
of a
test
lamp to the core or shaft (not on

bearing
surface) and touch each commutator
seg­
ment with the other prod. If the lamp lights, the

armature
segment
is grounded and the armature must be replaced.

To
test
for short in armature coils, a growler,

Fig.
H-21, is necessary. Place the armature on the growler and lay a thin steel strip on the armature

core.
The armature is then rotated slowly by hand

and
if a coil is shorted, the steel strip
will
vibrate.

Should
a coil be shorted the armature must be
replaced.

If
precision
test
equipment is available, the cus­

tomary
accurate
tests
can be made in accordance 188

H

ELECTRICAL
SYSTEM

FIG.
H-21—GROWLER
end so it rests on the pulley with the commutator
end up.

While
holding brushes clear of commutator with
the thumbs, place generator housing and field coils assembly in position, turning front end

bracket
so the dowel pin in housing enters
hole
in
end head. Place commutator end plate on shaft

and
install long frame screws.

When
reinstalling the generator on the engine, the

bracket
bolt torque wrench reading is 25 to 35 lb-ft. [3,4 a 4,8 kg-m.].

H-41.
CURRENT-VOLTAGE REGULATORS •
F4 Engine

H-42.
Description and
Operation
For
replacement,
voltage
regulator and generator must be matched for
voltage
and capacity, polarity,

and
common source of manufacture. Otherwise,
either a
loss
of ampere capacity or a burned out generator
will
result.

These
regulators are used with shunt-type gen­

erators
and have three units each with a separate function to perform. These units are the circuit

breaker
unit, the
voltage
regulator unit, and the

current
limiting regulator unit.

H-43.
Circuit
Breaker

It
consists of
an
electromagnet and a set of contacts.

The
contacts are mounted with one on a stationary

bracket,
and the other on a movable armature

which
is controlled by the electromagnet. The movable contact is mounted on a spring arm so that as the contacts open and
close
a slight wiping
action is produced.

The
electromagnet of the circuit breaker has two
windings, one, the shunt coil which is connected across the generator output like a voltmeter and
the other a series coil connected in series with the
generator output like an ammeter.These two coils

are
wound in the same direction so that when the
generator is charging the battery, the magnetism
of the series coil increases the total magnetism.

When
the battery discharges back through the generator, the magnetism of the series coil is re­ versed and the magnetism of the two coils is
opposed.
This
results in a decreased
pull
on the

armature
and spring action
opens
the contacts.
10240

FIG.
H-22—PRESTOLITE VOLTAGE REGULATOR
1—
"ARM"
Terminal

2—
"FLD"
Terminal

3— "BAT"
Terminal
The
sequence of operation of the circuit breaker is
as follows:

When
the generator is not running, the contacts
are
open. When the generator is started, the
voltage
builds up at the armature terminal and in the shunt

coil
and as
soon
as it reaches the value for which
the circuit breaker is calibrated, there is sufficient magnetism created by the shunt coil to
pull
down
the armature, closing the contacts which auto­
matically
connects the generator to the battery.

With
the contacts thus closed the current in the
series coil is flowing from the generator to the battery or in the same direction as the current in
the shunt coil, so that the
pull
on the armature is

increased
by the magnetism of the series coil.

When
the
engine
is stopped and the generator
loses

speed, the
voltage
falls, and as
soon
as the gener­
ator
voltage
drops below the battery terminal vol­
tage,
the current flows from the battery to the generator, reversing the direction of current in the
series coil so that the magnetism created by the series coil
opposes
and reduces the magnetism of
the shunt
coil.
This
reduces the
pull
on the
armature

to a point where spring action
opens
the contacts.

H-44.
Voltage
Regulator

The
function of the
voltage
regulator is to hold
the generated
voltage
at a predetermined value as 190

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

H
long as the circuit values allow the voltage to build
up to the operating voltage.
The
electromagnet of the voltage regulator unit has

a
winding of many turns of fine wire and is con­
nected across the charging circuit so that the sys­ tem voltage controls the amount of magnetism.
The
contacts of the voltage regulator unit are con­
nected in the generator field circuit so that the field

circuit
is completed through the contacts when they

are
closed and through a resistor when the contacts
are
opened.

When
the voltage rises to a predetermined value
there is sufficient magnetism created by the regu­

lator
winding to
pull
the
armature
down.
This
opens

the contacts and inserts resistance in the field
cir­

cuit
of the generator thus reducing the
field
current.
The
generated voltage immediately drops, which
reduces the
pull
on the
armature
to the point where
the spring closes the contacts. The output again

rises
and the cycle is repeated.

These
cycles occur at high enough frequencies to
hold the generated voltage at a constant value and

will
continue as long as the voltage of the circuit
is high enough to keep the voltage regulator unit

in
operation.
With
the addition of a current load great enough to lower the battery voltage below
the operating voltage of the unit, the contacts
will

remain
closed and the generator
will
maintain a
charging
rate as limited by its speed or the current

limiting
regulator.

Due
to the
effect
of heat on the operating
charac­

teristics of regulator windings it is necessary to
compensate for the changes in coil resistance when
the regulator is operating under varying tempera­

ture
conditions.
This
is accomplished through the
use of a nickel iron magnetic by-pass on the volt­
age regulator unit.
This
shunt by-passes
some
of
the magnetic flux when the unit is cold and allows most of the flux to act on the armature when the

unit
is hot.
Thus
when the coil is hot and not as
efficient, the magnetic shunt reduces the amount of flux needed to vibrate the armature.

The
compensation is usually more than enough to

offset
the changes in regulator coil resistance due
to heat. The excess compensation allows the regu­

lator
to operate at higher voltage under cold
operating conditions than under hot conditions.
This
is necessary as it requires a higher voltage to charge a battery with its internal resistance in­

creased
by low temperatures.

H-45.
Current-Limiting
Regulator

The
function of the current-limiting regulator is to limit the output of the generator to its maxi­

mum
safe output.

The
electromagnet of the current regulator unit
consists of
a
winding of heavy
wire
that is connected
in
series with the generator output. When the gen­

erator
output reaches a predetermined value, the
current
in the winding produces enough magnetism
to overcome the spring tension and
pull
the
arma­
ture
down.
This
opens
the contacts and inserts re­
sistance in the field circuit of the generator.
With
the field current reduced by the resistance, the
generator output falls and there is no longer enough
magnetism to hold the contacts open. As soon as
the spring closes the contacts, the output rises and the cycle is repeated. These cycles occur at high
enough frequencies to limit the output to a mini­
mum
fluctuation.

H-46.
Preliminary Inspection

a.
Wiring—Check
the wiring to see that it is prop­
erly
connected to the generator.

b.
Generator
Performance—Make
sure the genera­
tor operates correctly without the regulator in the
circuit.
Remove the armature and battery leads

from
the regulator and connect an ammeter be­
tween them. Remove the field lead from the regu­

lator
and while operating at idle speed touch the
field
lead
to the regulator base. Increase the speed slowly noting the charging rate.

CAUTION:
Do not increase the output above
the rated output of the generator.

If
the generator output
will
not build up inspect
the wiring harness for shorts and
opens
and remove the generator for an overhaul. To check the genera­
tor circuit when a suitable ammeter is unavailable,

Fig.
H-19, disconnect the armature cable at the

regulator.
Connect one lead of
a
12v
test
lamp to the regulator terminal marked "armature" and with
the engine running, ground the other lead. Should
the
test
light
fail
to
burn
there is a fault either in the generator or regulator. To localize the fault, discon­
nect both the
"Field"
and
"Armature"
cables at the generator. Connect a wire from the
"Field"
ter­
minal
to ground and use a 60 watt, 110 volt
test

lamp
to ground the
"Armature"
terminal. If the
generator is charging satisfactorily the
test
lamp

will
glow
at approximately 1500 rpm. engine speed
and
the fault
will
be definitely localized in the
regulator.

c.
Incorrect Regulator—Make sui he regulator
is the correct type for use with the generator.

d.
Battery—Check
the specific gravity and termi­

nal
voltage of the battery. If the \ ttery is not up
to specifications substitute temporarily
for
test
pur­
poses
a fully charged battery of the same type and
capacity.

e. High Resistance Connections—Inspect the
wir­
ing between the generator, regulator and battery for broken wires and high resistance connections.

Pay
special attention to the ground connections at
all
three units. Connect a reliable ammeter with 1-ampere graduations in series with the regulator

B-terminal
and the lead removed from this
terminal.
Run
the generator at a medium speed and
turn
on the lights or accessories until the ammeter shows a 10-ampere charging rate. At this charging rate
measure the voltage drop between the following
points using an accurate voltmeter graduated in
,1-volt divisions. The voltmeter should not show

a
reading above the maximum noted.
Generator
"A" terminal to regulator
"A"
terminal
—.1-volt maximum.

Generator
"F"
terminal to regulator
"F"
terminal
—.05-volt maximum.

Battery
terminal to regulator "B" terminal— .1-volt maximum.

Regulator
ground screw to generator frame— .03-volt maximum. 191

H

ELECTRICAL
SYSTEM
Regulator
ground screw to battery ground post
—.03-volt maximum.

Generator
frame to battery ground post—.03-volt
maximum.

H-47.
Test Procedure

a.
Circuit
Breaker—Connect
an ammeter in series between the regulator B-terminal and the lead
wire
removed from that terminal. Connect a
voltmeter between the regulator
A-terminal
and the regulator mounting base. Disconnect the field lead

from
the regulator
F-terminal
and insert a variable resistance (3 amp., 50 ohm capacity) between the

lead
and the regulator terminal. Run the generator
at about 1000 generator rpm. Insert all the re­
sistance in the field
circuit,
then slowly reduce the
resistance noting the voltage reading just before the change caused by the closing of the circuit

breaker.
Increase the charging rate to the figure
specified for the regulator being tested then reduce
the charging rate by inserting resistance in the
field
circuit.
Note
the voltmeter and ammeter

reading
just before the circuit breaker
opens
and
the ammeter reading drops to zero. The closing voltage and the opening voltage or current should
be within the limits specified. An accurate method
for noting the exact instant of the opening or closing
of the circuit breaker is to connect a headphone (2000 ohms or higher) to the battery and armature

terminals
of the regulator. When the contacts
open or close a
click
will
be
heard
in the headphones.
To
adjust the closing voltage change the armature

spring
tension by bending the hanger at the lower end of the spring. Increase the spring tension to

raise
the closing voltage or decrease the tension
to lower the closing voltage. To adjust the opening voltage raise or lower the stationary contact
keeping the contacts perfectly aligned. Increasing
the contact gap lowers the opening
'
voltage.
Change
the contact gap by expanding or contract­
ing the stationary contact bracket, keeping the
contacts aligned. Do not adjust the gap between
the contacts to less than the specified minimum.

b.
Voltage Regulator—Connect the ammeter as in

step
a. Connect the voltmeter between the regulator
B-terminal
and the regulator base. Remove the

variable
resistance from the field
circuit.
Run the
generator at
half
output for 15 minutes to bring
the regulator to normal operating temperature.

Keep
the cover on the regulator during the
warm-

up period and also when taking readings.
Stop the engine then bring it up to approximately 2500 generator rpm. Adjust the amperage to
half

maximum
output by turning on lights or accessor­
ies and then
note
the voltmeter reading.
This
read­

ing should be within the limits specified for the voltage regulator operation. To adjust the oper­
ating voltage change the
armature
spring tension by
bending the hanger at the lower end of the
arma­

ture
spring. After each adjustment
stop
the engine then restart it.
Bring
it up to speed and adjust the

current
before taking a reading. In order to obtain

an
accurate indication of the operation of the volt­
age regulator unit connect a headphone (2000 ohm

or
higher) between the
F-terminal
and ground to

pick
up the sound of the opening and closing of the
contacts. The clicks should be regular and clear without irregularities or missing. If the
tone
is not

clear
and regular remove the regulator cover and
inspect the contacts. The contacts should be flat
and
not burned excessively and should be aligned
to make
full
face contact. If the contacts need
cleaning refer to paragraph d for the method.

c.
Current
Regulator—Connect the regulator and the
test
equipment as in
step
b. Running the generator at approximately 3000 generator rpm.,

turn
on lights and accessories so that the generator must charge at maximum rate. The ammeter should give a reading within the limits specified.

To
adjust opening amperage, change the armature

spring
tension by bending the hanger at the lower
end of the armature spring. After each adjustment,

stop
the engine, then restart it.
Bring
the engine up to speed and take an ammeter reading. Keep
the cover on the regulator when taking
these

readings.

Connect
a headphone (2000 ohms or higher) be­
tween the regulator
F-terminal
and ground to pick
up the sound of opening and closing of the contacts.

Clear,
regular clicks should be heard over the
headphones; they should not be
irregular
or missing.
If
the
tone
is not clear and regular remove the
regulator cover and inspect the contacts. The
contacts should be flat and not burned excessively

and
should be aligned to make
full
face contact. If
the contacts need cleaning refer to paragraph d.
below for the method.

d.
Contacts—Inspect the contacts on all three
units.
In normal use the contacts
will
become

grayed.
If the contacts are burned or dirty or if they are not smooth, file the contacts with a #6

American,
Swiss cut, equalling file. Move the file

parallel
and lengthwise to the armature.
File
just
enough so that the contacts present a smooth
sur­

face toward each other. It is not necessary to remove every trace of pitting. After filing, dampen

a
piece of linen or lintless bond tape in refined

carbon
tetrachloride and draw the tape between
the contacts. Repeat with a dry piece of tape. Use
clean
tape for each set of contacts.
e. Recheck—Operate the unit at
half
maximum
output for five minutes with the cover on the regu­

lator.
Repeat the testing procedure for all units as described in a, b, c above. Be sure cover is on regu­

lator
when taking readings.

H-48.
Quick
Checks

H-49.
Low Charging Rate with a
Fully
Charged
Battery

A
fully charged battery and a low charging rate
indicates normal regulator operation.
A
further check of the regulator operation can be
made by using the starting motor for 5 to 10
seconds with the ignition switch in the "off" posi­ tion.
Then
start the engine and operate at a genera­
tor speed of 2500 to 3000 rpm. The charging rate should rise to its maximum value then taper off to

a
minimum charge as the battery becomes charged.

H-50.
High Charging Rate with a
Fully
Charged
Battery

This
is usually an indication that the voltage regu­

lator
is not operating correctly. The high voltage 192

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H
H-111.
Brushes

Check
brush length. If brushes are worn to one-

half
their original length, replace them. Also check
for
cracks,
chips, damaged mounting holes, oil

saturation,
or other damage; replace brushes.

H-112.
Commutator

Check
the commutator for wear and discoloration.
If
the commutator is rough or worn the armature
should be removed and the commutator turned
down in a lathe. A discolored commutator should
be cleaned with carbon tetrachloride and inspected.

Scratches
on the commutator may be removed

with
sand paper. Use compressed air to remove

sand
particles after cleaning.

H-113.
Armature

Visually
inspect the armature for mechanical

defects
before checking for shorted or grounded
coils. Use a set of
test
probes for testing armature

circuits.
To
test
the armature for grounds, touch
one point of the
test
probes to a commutator
seg­
ment and touch the other point to the core or shaft.
Do not touch the points to the bearing surface or
to the brush surface as the arc formed
will
burn
the smooth finish. If the lamp lights, the coil con­
nected to the commutator
segment
is grounded.

H-114.
Field
Coils

Using
test
probes, check the field coils for both ground and open circuits. To
test
for ground, place
one probe on the motor frame or
pole
piece and
touch the other probe to the field coil terminals.
If
a ground is present, the lamp
will
light.

To
test
for open circuits, place the probes on the
field coil terminal and on an insulated
brush.
If
the light
does
not light, the coil is open circuited.

H-115.
Brush
Holder Inspection

Inspect
brush
holders for distortion, wear, and other
damage.
Check
that brush holders pivot freely on

their
pivot pins.
Check
brush spring tension with

a
spring scale. Hook the spring scale under the
brush
holder at the brush and
pull
on a line
paral­

lel
to the side of the
brush.
Note
scale reading just
as brush leaves commutator. Tension must be 35 oz. [9,925 kg.] minimum. Replace brush springs
if
tension is insufficient.

H-116.
Solenoid
Coils

Check
solenoid coil as follows:

a.
Remove screw from motor terminal of solenoid

and
bend field coil leads away from terminal.
Con­
nect terminal to ground with a heavy jumper wire.
See
Fig.
H-48.

b.
Connect a 12-volt battery, a high-current
vari­

able resistance, and an ammeter of 100 amperes

capacity
in series
between
S terminal of solenoid

and
ground; battery negative is to be connected
to ground. Connect a heavy jumper wire from
solenoid base to ground terminal of battery.
Con­

nect a voltmeter
between
base of solenoid and

small
S terminal of solenoid. Refer to Fig. H-48.
12455

FIG.
H-48—TEST CONNECTIONS,
STARTER
SOLENOID
COIL
1— S
Terminal

2—
Solenoid

3—
Ground
Connection 4—Voltmeter 5—Ammeter
6—
12-Volt
Battery
7—
Ground
Connection*
c.
Slowly decrease resistance until voltmeter
read­

ing increases to 10 volts.
Note
ammeter reading.

This
is current drawn by both windings in
parallel
;

it
should be 42 to 49 amperes at 10 volts, with solenoid at room temperature.

d.
Disconnect jumper wire from motor terminal
of solenoid. Increase resistance until voltmeter

reads
10 volts;
note
ammeter reading.
This
is
cur­

rent
drawn by hold-in winding only; it should be 10.5 to 12.5 amperes at 10 volts, with solenoid at
room temperature.
e. If solenoid windings do not rest within specifi­ cations given, replace solenoid switch assembly.

H-117.
Starting Motor Reassembly

a.
Lubricate
shift lever linkage and fasten in drive housing with lever stud.

Caution:
Do not lubricate solenoid plunger or solenoid cylinder.

b.
Install
return spring on solenoid plunger and

insert
plunger into solenoid cylinder. Apply sealing
compound on both sides of solenoid flange where it

extends
between
drive housing and field frame.

Attach
plunger to shift lever with fulcrum pin.

Fasten
solenoid to drive housing with two mount­
ing screws.

c.
Lubricate
armature shaft with silicone grease.
Install
assist spring and drive assembly on shaft

with
pinion outward.

d.
Install
pinion
stop
retainer on armature shaft

with
recessed side outward. Place a new snap ring on drive end of shaft and hold it in place with a
hard
wood block. Strike block with hammer to
force snap ring over end of shaft; slide the ring
down into
groove
in shaft. See Fig. H-49, left hand view. 209

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

H
H-152.
ELECTRICAL
SPECIFICATIONS
MODEL HURRICANE
F4 ENGINE DAUNTLESS
V-6
ENGINE

BATTERY:
Make
Model Hour Rating.

Voltage
Terminal
Ground

SPECIFIC
GRAVITY:
Fully
Charged
Recharged At
Location

GENERATOR:
Make.
Model

Ground
Polarity
Controlled Output

Control

Armature End Play
Brushes

Brush
Spring Tension

REGULATOR:
Make
Model:
For
GJP
7202,
GJP
7402A

Type
Cutout Relay: Closing
Voltage
@
Generator rpm..........
Reverse Current to Open.
Regulated
Voltage

Regulated Current

ALTERNATOR:
Make
Model
Ground
Polarity
Rated Output
Rated Field
Coil
Draw

At
70°F.
and
10-volt

Capacitor Capacity

REGULATOR:
Make
Model
Type

STARTING
MOTOR:
Make
Model
Brush
Spring Tension

LOCK
TEST:
Temperature
Amp.
(Max.)
Volt
Stall
Torque (Min.)

NO LOAD TEST:
Tempesature

Amp.
(Max.)
Volt
Rpm.
(Min.)

DRIVE:
Type

COIL:
Make.
Model

Primary
Resistance Secondary Resistance
Prestolite

HS
11-50
50 Ampere-hour
12-volts

Negative

1.260
1.225
Engine Compartment- Right Rear

Prestolite

GJP-7402A
Negative
35 amp.

CV
Regulator .003" to .010"

[0,076
a 0,25 mm.] 2
18 to 36 oz.
[510 a 1020 gr.]

Prestolite

VBO-4201E-4A
Vibrator

12.6 to 13.6 @ 1325 3 to 5 amp. 14.2 to 14.4
36 amp. max.
Motorola
A12 NW 526
Negative
35 amp.
1.7 to 2.3 amp. .1 mfd.
Motorola
R-2-K-1

Transistor

Prestolite

MDU-7004
32 to 40 oz. [907 a 1134 gr.]

70°F.
[21°C] 295 4
6 lb-ft. [0,83
kg-m.]

70°F.
[21°C.;
50
10

5300

Bendix Folo-Thru
Prestolite
200691

3.9 to 4.2
ohms

9400
to
11,700
ohms
Prestolite

HS
11-50
50 Ampere-hour
12-volts

Negative

1.260
1.225
Engine Compartment- Right Rear

Prestolite

GJP-7402A
Negative
35 amp.

CV
Regulator .003" to .010"

[0,076
a 0,25 mm.] 2
18 to 36 oz.
[510 a 1020 gr.]

Prestolite

VBO-4201E-4A
Vibrator

12.6 to 13.6 @ 1325 3 to 5 amp. 14.2 to 14.4
36 amp. max.
Motorola
A12 NW 528
Negative
35 amp.
1.7 to 2.3 amp. .1 mfd.
Motorola
R-2-K-1

Transistor
Delco-Remy

1107391,
1108366,
1108375

32 to 40 oz. [907 a 1134 gr.]
Not Applicable Not Applicable

70°F.
[21°C] 75
10.6

6200

Overrunning Clutch Delco-Remy
1115247

1.28 to 1.42
ohms

7200
to
9500
ohms
Prestolite

MHA-7008
32 to 40 oz. [907 a 1134 gr.]

70°F.
[21°C] 200 4
3 lb-ft. [0,41
kg-m.]

70°F.
[21°C] 43
10.0

9000

Bendix Folo-Thru

Prestolite
201700

4.25 to 4.60
ohms

5200
to 6100
ohms
223