1953 JEEP DJ Service Manual

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

H

12968
FIG.
H-4—WIRING
DIAGRAM—MODELS
CJ-5, CJ-6, DJ-5, DJ-6
LATE
F4
ENGINE

1—
Left
Headlamp
2—
Left
Parking and Signal Lamp
3— Right Parking and Signal Lamp 4— Right Headlamp
5— Generator
6— Ignition Distributor
7—
Oil
Pressure Sending Unit
8— Junction Block
9—
Horn

10— Foot Dimmer Switch 11—
Stop
Light Switch — Front
12— Temperature Sending Unit
13— Ignition
Coil

14— Starting Motor 15— Battery Ground Cable
16— Battery
17— Voltage Regulator 18—
Fuse

19— Instrument Cluster

A—Hi-Beam
Indicator

B—Auxiliary
C—Instrument
Lights

D—Oil
Pressure Indicator
E—Charging
Indicator
F—Temperature
Indicator

G—Fuel
Gauge
H—Instrument Voltage Regulator
20— Ignition and Starter Switch 21—
Flashei
(Directional Signal)
22—
Horn
Button 23— Directional Signal Switch
24— 4-Way Flasher Switch
25—
Flasher
(4-Way)
26—
Fuse

27—
Main
Light Switch 28—
Stop
Light Switch — Rear
29—
Fuel
Gauge
Tank
Unit
30—
Back-Up
Light Switch
31— Right
Tail
and
Stop
Lamp
32— Right Back-Up Lamp
33—
Left
Back-Up Lamp
34—
Left
Tail
and
Stop
Lamp

in
which the key can be removed. Turning the key
to the
left
energizes
auxiliary
equipment
such as
windshield wipers, radio, and heater. The turn
signal
lights
will
operate
with the
ignition
key in
either the
left
or right
position.
The
ignition
switch is held in
position
by a
tension
spring on the back
of the instrument panel and a
notched
bezel on
the front of the instrument panel.
H-8.
Lighting System

The
wiring for the lighting
system
is shown in the
wiring diagrams, Figs. H-2 thru H-7 of the manual,
which indicate the various units in relation to their

position
in the vehicle. The lighting circuit is pro­
tected
by an overload circuit breaker
mounted
on the rear of the light switch.
The
main light switch controls the lighting
system
177

H

ELECTRICAL
SYSTEM

14365

FIG.
H-5—WIRING
DIAGRAM—F4
ENGINE
CURRENT
MODEL
1—
Left
Headlamp

2—
Left
Parking and Signal Lamp
3—
Right
Parking and Signal Lamp

4—
Right
Headlamp
5—
Marker
Lamp
— Amber
6—
Generator
7—
Distributor

8—
Ignition
Coil

9— Starting Motor
10— Battery Ground Cable
11—
12
Volt
Battery

12—
Flasher
(Directional Signal)
13— Instrument Cluster
A—Hi-Beam
Indicator

B—Auxiliary
C—Instrument Lights
D—Oil
Pressure
Indicator
E—Charging Indicator
F—Temperature Indicator
G—Fuel
Gauge
Indicator
H—Instrument Voltage Regulator
14—
Ignition
and
Starter
Switch
15—
Horn
Button 16—
Directional
Signal Switch 17— 4-Way
Flasher
Switch
18—
Flasher
(4-Way)
19—
Windshield
Wiper Motor Switch
20—
Main
Light
Switch

21—
Fuel
Gauge
Tank
Unit

22—
Back-Up
Light
Switch
23—
Marker
Lamp — Red 24—
Right
Tail
and Stop Lamp
25—
Right
Back-Up Lamp
26—
Left
Back-Up Lamp
27—
Right
Tail
and Stop Lamp
28—
Marker
Lamp — Red 29— Stop
Light
Switch
30— Foot Dimmer Switch

31—
Windshield
Wiper Motor Assembly

32—
Voltage Regulator
33— Temperature Sending
Unit

34—
Oil
Pressure
Sending
Unit

35— Spark
Plugs
&
Cables

36—
Horn

37— Junction Block
38—
Marker
Lamp — Amber
through a
two-position
push-pull switch located on
the
left
side
of the control panel.
The
foot-operated
headlight dimmer switch is
mounted on the floorboard to the
left
of the steering
column.

H-9.
PRESTOLITE
DISTRIBUTOR
—
DAUNTLESS
V-6 and

HURRICANE
F4
ENGINE

The
Prestolite distributor on the F4
engine
is
mounted on the right
side
of the
engine
and is op­
erated by a coupling on the oil pump shaft, see Fig.
D-l,
which is driven by a spiral gear on the cam­
shaft. The spark advance is fully automatic, being controlled by built-in centrifugal
weights.
The Pres­

tolite
distributor on the V-6
engine
(Fig. H-8) is mounted at the
left
front of the
engine
on the tim­
ing chain cover. It is driven by a spiral gear on the
camshaft. The spark advance is fully automatic,
being controlled by built-in centrifugal
weights,
and by a vacuum advance system. While
some
parts of the distributor may be checked or replaced
with the unit mounted on the
engine,
it is
best
to periodically remove it for a thorough check. Infor­ mation covering the parts which can be serviced
without removal is
given
below.
The
Prestolite distributor installed on the V-6 en­

gine
is similar in construction to the distributor in­
stalled on the F4
engines
except
for the addition of

a
vacuum advance mechanism.
The
same checking procedures outlined in Par. C- 10a, are used for the Prestolite V-6 distributor with

exception
of specifications.
H-10. Distributor Cap

The
distributor cap should be inspected for cracks,
carbon runners and
evidence
of arcing. If any of

these
conditions
exists, the cap should be replaced.
Clean
any corroded high
tension
terminals.

H-11.
Rotor
Inspect the rotor for cracks or
evidence
of
excessive

burning at the end of the metal strip.
After a distributor rotor has had normal use the
end of the rotor will
become
burned. If burning is found on top of the rotor it indicates the rotor is
too short and
needs
replacing. Usually when this condition is found the distributor cap
segment
will 178

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H

12967
FIG.
H-6—WIRING
DIAGRAM—LATE
V6
ENGINE

1—Left Headlamp

2—
Left
Parking and Signal Lamp
3—
Right
Parking and Signal Lamp

4—
Right
Headlamp
5— Voltage Regulator
6—
Alternator
7—
Oil
Pressure
Sender

8— Temperature
Sender

9—
Ignition
Distributor
10— Junction Block

11—
Horn

12—
Ignition
Coil

13— Starting Motor
14— Battery Ground Cable 15— Foot Dimmer Switch 21-
16— Stop
Light
Switch — Front 22-
17— Ballast 23-
18—
Flasher
(Directional Signal) 24-
19—
Fuse
25-
20— Instrument Cluster 26-

A—Hi-Beam
Indicator 27-

B—Auxiliary
28- C—Instrument Lights 29-

D—Oil
Pressure
Indicator 30-
E—Charging Indicator 31-F—Temperature Indicator 32-
G—Fuel
Gauge
33-
H—Instrument Voltage Regulator 34-
-Ignition
and
Starter
Switch

-Horn
Button

-Directional
Signal Switch
-4-Way
Flasher
Switch

-Flasher
(4-Way)

-Fuse

-Main
Light
Switch
-Stop
Light
Switch —
Rear

-Fuel
Gauge
Tank
Unit

-Back-Up
Light
Switch

-Right
Tail
and Stop Lamp

-Right
Back-Up Lamp

-Left
Back-Up Lamp

-Left
Tail
and Stop Lamp
be burned on the horizontal
face
and the cap will

also
need
replacing. H-12. Condenser

The
condenser
prolongs
the
life
of the distributor

points
by
preventing
arcing at the
contacts.
It
also
provides
a
hotter
spark by creating a reverse
surge

of current which rapidly breaks
down
the
magnetic

field of the coil by
demagnetizing
the core. Should
the
condenser
be leaky, a weak spark will result.

Check
the
condenser
lead for broken wires or
frayed insulation. Clean and
tighten
the
connec-
179

H

ELECTRICAL
SYSTEM

ffKHs)

3—<§)

FIG.
H-7—WIRING
DIAGRAM—V6
ENGINE
CURRENT
MODEL
1—
Left
Headlamp
2—Left Parking and Signal Lamp
3— Right Parking and Signal Lamp
4—Right Headlamp 5—
Marker
Lamp — Amber
6— Alternator 7— Voltage Regulator
8— Starting Motor
9— Battery Ground Cable
10— 12 Volt Battery
11—
Flasher
(Directional Signal)
12— Instrument Cluster
A—Hi-Beam
Indicator
B—Auxiliary

C—Instrument
Lights

D—Oil
Pressure Indicator
E—Charging
Indicator

F—Temperature
Indicator

G—Fuel
Gauge Indicator
H—Instrument Voltage Regulator
13— Ignition and Starter Switch
14—
Horn
Button
15— Directional Signal Switch
16— 4-Way Flasher Switch 17—
Flasher
(4-Way)
18— Windshield Wiper Motor Switch
19—
Main
Light Switch
20—
Fuel
Gauge
Tank
Unit
21—
Back-Up
Light Switch
22—
Marker
Lamp — Red
23— Right
Tail
and
Stop
Light 24— Right Back-Up Lamp
25—
Left
Back-Up Lamp 26—
Left
Tail
and
Stop
Light
27—
Marker
Lamp — Red
28—
Stop
Light Switch
29— Foot Dimmer Switch
30— Windshield Wiper Motor Assembly
31—
Ballast
Resistor 32— Ignition
Coil

33—
Spark
Plugs and Cables 34— Temperature Sending Unit
35—
Oil
Pressure Sending Unit 36—
Horn
37— Junction Block
38—
Marker
Lamp — Amber

lions
on the terminal
posts.
Be sure
condenser
is
mounted
firmly on the distributor for a
good
ground
connection.

Should a
condenser
tester
be available the capacity for
both
F4 and Prestolite V6
condenser
should
check from .25 to .28 microfarads. In the
absence

of
tester,
check by substituting a new
condenser.

H-13. Distributor Points
a. Examine the distributor
points.
If
they
show

wear,
poor
mating, transferred metal, or pitting,

then
new
ones
should be installed. Clean the
points

with a suitable
solvent
and a stiff bristled brush.
b. Check the
alignment
of the
point
for a full,
square
contact.
If not correctly aligned, bend the
stationary
contact
bracket slightly to provide align­
ment.

c. The
contact
gap should be set at .020"
[0,508
mm.],
on the F4 and .016"
[0,406
mm.] on the
Prestolite V6. Adjustment of the gap is accom­ plished by
loosening
the lock screw and turning adjusting eccentric screw until correct gap is
secured. Be sure that the fiber block on the breaker

arm
is resting on the
highest
point
on the cam while the adjustment is
being
made. Recheck the gap
after locking the adjustment.
d. Apply a thin film of cam lubricant to the cam to
lessen
fiber block wear.
e. Using Tool C-4094, check
point
contact
spring
pressure, which should be
between
17 and 20

ounces
[0,487
a
0,567
kg.] on the F4 and 17 to 22 oz.
[0,487
a
0,624
kg.] on the Prestolite V6.

Check
with a spring scale
hooked
on the breaker

arm
at the
contact
and pull at right
angle
to the
breaker arm. Make the reading just as the
points

separate. Adjust the
point
pressure by
loosening
the stud holding the end of the
contact
arm spring
and slide the end of the spring in or out as
neces­

sary.
Retighten the stud and recheck the pressure. Too low a- pressure will
cause
engine
missing at
high
speeds.
Too high a pressure will
cause
rapid
wear of the cam, block, and
points.
180

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H

12955

FIG.
H-8—PRESTOLITE
DISTRIBUTOR—DAUNTLESS V-6 ENGINE 1—
Cap
2—
Rotor

3—
Lubricating
Wick

4—
Snap
Ring
5—
Condenser

6—
Contact
Set 7—
Breaker
Plate
8—
Cam
and Stop Plate 9—
Spring
(2)
10—
Governor
Weight

11— Cam
Spacer

12—
Gear
13—
Gear
Pin
14—
Washer

15—
O-Ring
Seal
16—
Bushing

17—
Distributor
Housing 18—
Vacuum
Chamber
19—
Washer
(Nylon)
20—
—Cap
Clamp
and Rings

21—
—Primary
Lead
22—
Washer
(outer upper,

23—
Washer
(inner upper)

2".—Drive
Shaft
H-14. Governor Mechanism
The
centrifugal advance mechanism consists of

an
automatic cam actuated by two spring con­
trolled centrifugal weights. As the
speed
of the distributor shaft increases with
engine
speed, the

weights
are thrown outward against the pull of the springs.
This
advances the cam causing the contact
points
to
open
earlier and thus advancing the

spark.
The centrifugal
type
governor should be checked for free operation. Hold the governor shaft
and
turn the cam to the
left
as far as possible

and
release it. The cam should immediately return to the original position without drag. Should a distributor
test
fixture be available it is

best
to make a check through the entire advance
range, following the instructions of the fixture manufacturer.

The
vacuum control unit is mounted separately
on the
outside
of the distributor housing on the
V6
Prestolite distributor.
The
vacuum control unit consists of an enclosed
spring-loaded diaphragm linked mechanically to the distributor. The air-tight side of the diaphragm
is connected to the intake manifold side of the

carburetor.
Under part throttle operation, the in­take manifold vacuum is sufficient to actuate the
diaphragm and cause the distributor to rotate in
its mount, thus advancing the spark and increasing fuel
economy.
During acceleration or when the
engine
is pulling heavily, the vacuum is not suf­
ficient to actuate the diaphragm and the distributor
is held in the retarded position by a calibrated

return
spring which bears against the vacuum
diaphragm.

H-15.
Distributor Removal

a.
Remove high-tension wires from the distributor cap terminal towers, noting the order in which
they

are
assembled to ensure correct reassembly.
b. Remove the primary lead from the terminal

post
at the coil.
c. Unlatch the two distributor cap springs and re­
move
the cap.

d.
Note
the position of the rotor in relation to the
base.
This
should be remembered to facilitate re­ installing and timing.
e. Remove the screw holding the distributor to the

crankcase
and lift the assembly from the
engine.

H-16.
Prestolite Distributor Disassembly

Refer
to Fig. H-8 and H-9.

a.
Remove the rotor. b. Remove the condenser.
c. Remove the distributor points.
d.
Remove nylon washer attaching vacuum ad­vance arm to breaker plate, V6 only. Remove two 181

H

ELECTRICAL
SYSTEM
FIG.
H-9—DISTRIBUTOR ASSEMBLY- HURRICANE F4 ENGINE 1—
Cap
6—Advance Plate
Lock
Screw
2—
Rotor
7—Oiler and
Felt
Wick

3—
Primary
Wire
8—Drive Shaft
4—
Breaker
Plate 9—Drive Shaft
Collar
and
Thrust
Washer 5—
Governor
Weights
attaching screws; remove vacuum advance unit
from housing.
e. Remove the two clamp
hinge
to breaker plate
screws; remove breaker plate from housing.
f. Remove the shaft assembly. To do this, file off
the upset end of the pin which is placed through
the collar and shaft at the lower end of the housing

and
drive out the pin with a suitable punch. Re­
move
the collar and washer.
Pull
the shaft from
the housing.
g. Should it be necessary to remove the cam as­
sembly, first remove the
felt
wick from the upper
end. Use
long-nose
pliers to compress and remove the spring locking clip located at the
bottom
of the

drilled
center opening of the cam. Remove the cam.

H-17.
Distributor Inspection

If
the shaft and bearings are worn sufficiently
to allow .005" or more
looseness
of the shaft,
they
must be replaced. Before installing new bearings,
soak them in medium grade
engine
oil and allow
them to
drain.
Wipe all oil from the upper part of
the housing.

Important:
After new bearing installation,
drill
a

y%"
[3,2 mm.] lubrication
hole
through the upper bearing
before
installing the drive shaft. Refer
to Fig. H-8 item 16.

At
assembly, apply a film of grease to the upper
drive
shaft washer and put a small amount of
grease in the bearing bore just
above
the bearings.

Lubricate
the governor mechanism sparingly with
medium grade
engine
oil in the oiler mounted on
the side of the housing and 5 drops on the
left

located in the center opening of the cam directly

below
the rotor. Place a very light smear of grease
on the cam and 1 drop of oil on the breaker arm pivot.
Before installing the distributor, check the friction

spring
mounted on the lower end of the drive shaft

and
replace it if worn or damaged. Inspect rod end of vacuum advance mechanism
for
excessive
wear. Push rod
into
unit as far as
possible, hold finger tightly over nipple, then release rod. After about 15 seconds, remove finger
from nipple, and
notice
if air is drawn
into
unit.
If
not, diaphragm is leaking and unit must be
replaced.

H-18.
Installation and Ignition
Timing

If
the
engine
crankshaft has
been
rotated, with the
distributor off, it
will
be necessary to place No. 1
piston in firing position to correctly install the distributor. Refer to
Pars.
C-10 and
C-ll. Oil
the distributor housing where it bears in the

cylinder
block and install the distributor on the
cylinder
block. Mount the rotor on distributor shaft

and
turn
the shaft until the rotor
points
towards No. 1
spark
terminal tower position (when cap is installed) with the contact
points
just breaking. Move the rotor back and forth slightly until the

driving
lug on the end of the shaft enters the
slot

cut in the oil pump gear and slide the distributor
assembly down
into
place. Rotate the distributor
body
until the contact
points
are just breaking.
Install
the hold down screw.

H-19.
Ignition
Coil
— F4 Engine

The
sealed coil
does
not require any special service
other than keeping the terminals and wire con­ nection clean and tight.

The
positive (+) terminal of the coil is connected
to the ignition switch and is also connected directly
to the starter solenoid to by-pass the resistance

during
cranking of
engine.

The
negative
(—) terminal is connected to the
distributor. The secondary (High tension) terminal
is connected by a short cable to the center terminal

in
the distributor cap.

Note:
Always make certain the coil wires are con­
nected to the proper coil terminals to ensure cor­
rect coil polarity.

H-20. DELCO DISTRIBUTOR
—
DAUNTLESS
V-6
ENGINE
The
distributor (Fig. H-10) is mounted at the
left

front of the
engine
on the timing chain cover. It
is driven by a
spiral
gear on the camshaft. The

spark
advance is fully automatic, being controlled 182

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

H
|
13399

FIG.
H-10—DELCO
DISTRIBUTOR—
DAUNTLESS
V-6
ENGINE

1—
Rotor
8—Vacuum
Unit

2—
Window
9—Breaker Cam
3—
All
Weather Cap
10—Drive
Gear

4—
Cap
Latch
11—Primary Lead 5—
Rotor
Mounting
Screw 12—Contact Set
6—
Lock
Washer 13—Condenser

7—
Advance
Mechanism
by
built-in
centrifugal weights, and by a vacuum

advance
system. Contact point opening is adjusted
through
a window in the distributor cap
while
the engine is
idling.
Some
parts
of the distributor may be checked or replaced
with
the distributor mount­
ed on the engine, but it is
best
to remove it periodi­
cally
for a thorough check. Information on
parts

which
can be serviced without removal is given
below.

Note:
Prestolite and Delco distributors are inter­

changeable
on V-6 engine equipped vehicles.

H-21.
Distributor Cap
The distributor cap should be inspected for cracks,
carbon runners and evidence of arcing. If any of

these
conditions exist, the cap should be replaced. Clean any corroded high tension terminals.

H-22.
Rotor
Inspect the rotor for cracks or evidence of
exces­

sive burning at the end of the metal strip.
After
a distributor rotor has had normal use, the
end of the rotor
will
become
burned. If burning is
found
on top of the rotor it indicates the rotor is too short and
needs
replacing. Usually when this
condition
is found the distributor cap
segment
will

be burned on the horizontal face and the cap
will

also
need
replacing.
H-23.
Condenser
The
condenser
prolongs the
life
of the distributor
points by preventing arcing at the contacts. It
also

provides a hotter spark by creating a
reverse
surge

of
current
which
rapidly
breaks
down the magnetic
field
of the
coil
by demagnetizing the core. Should
the
ccnaenser
be leaky a weak spark
will
result. Check the
condenser
lead for broken wires or

frayed
insulation.
Clean and tighten the connections
on
the terminal
posts.
Be
sure
the
condenser
is mounted
firmly
on the distributor for a good ground
connection.

Should
a
condenser
tester
be available the capacity
should check
from
.18 to .23 microfarads. In the

absence
of a
tester
check by substituting new con­
denser.

H-24. Distributor Points

a-
Examine distributor points. Using
Tool
C-4094, check point contact spring
pressure,
should be 19 to 23 oz. [0,538 a 0,652 kg.]. Install new points

if
they are
worn,
pitted,
mate
poorly, or show
signs

of
metal transfer. Should premature
ignition
point

failure
occur
because
of dust entering the
distri­

butor cap and causing
excessive
wear to the
ignition

point
fiber block, perform the
following
correc­
tions after installing new distributor points.
FIG. H-l
1—SEALING
DISTRIBUTOR
CAP

1—Caulking
Compound
183

H

ELECTRICAL
SYSTEM

14237

FIG.
H-l2—DRILLING DISTRIBUTOR
CAP 1—%'
Vent
Hole
Location
Seal
the distributor cap access window and the

area
beneath the distributor cap with caulking
compound as shown in
Fig. H-ll.
At approximately
180°
from the distributor cap access window,
drill
a
[2,38 mm.] vent
hole
[31,75
mm.]
from the
bottom
of the distributor cap as shown

in
Fig. H-l2. b. To adjust breaker point cam dwell, refer to

Par.
C-10.

H-25.
Centrifugal Advance

Refer
to Fig. H-13.
Inspect for
excessive
wear
between
centrifugal

weights
and advance cam, or pivot pins.
Turn

weight
base plate in a clockwise direction until

weights
are fully extended, then release and allow springs to return to retard position. Repeat several times. Springs should return
weights
to
stop
with­out sticking and there should be no
excess
free

movement
in the retard position.

H-26.
Distributor Removal

a.
Disconnect the distributor primary wire from
coil
and disconnect
hose
from vacuum advance
mechanism of distributor. Insert a screwdriver in upper
slotted
end of two distributor cap retainers.

Press
downward, and turn 90
degrees
counterclock­
wise to release. Remove cap from distributor hous­ ing.
b. Make an index
mark
on distributor housing

(Fig.
H-14) in line with center of rotor. Carefully

note
the direction the vacuum unit
points
in
rela­

tion to
engine
so that the distributor can be in­
stalled in the same position after it is serviced.

Caution:
If
engine
is turned over while distributor is removed,
complete
ignition timing procedure
must be followed upon distributor installation.
c. Remove attaching cap screw and distributor
clamp from timing chain cover.
Lift
distributor up­

ward
and remove it from timing chain cover.

H-27.
Distributor Disassembly (Delco)

Refer
to Fig. H-l5.

a.
Remove rotor, breaker point assembly, and capacitor from distributor.
FIG.
H-13—CENTRIFUGAL ADVANCE
MECHANISM (DELCO)
A—No
Advance
1—
Advance
Weights

2—
Advance
Cam
B—Full
Advance

3—Full
Advance
FIG.
H-14—DELCO DISTRIBUTOR

ROTOR
POSITION
1
—Rotor
Tip
Lined
Up
With
Notch

184