1953 JEEP DJ air condition

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL

B
LUBRICATION
AND
PERIODIC SERVICES

Contents
PAR. SUBJECT
PAR.
SUBJECT

GENERAL
.B-l
Chassis
Lubrication
B-7
Engine
Lubrication System B-4, B-6

Special
Lubricants B-2

Fresh
Lubricant.
.B-3

LUBRICATION CHARTS
. Pages 8, 9

SERVICE
MAINTENANCE SCHEDULE.
.B-8
Air
Cleaner
B-2
5,
B-2
6
Air
Filter
—
F.E.E.C.
System Canister
B-2
4

Axle
U-Bolts B-49 Body
Lube
Points: B-65 Hood Hinge Pivot Points B-66

Glove
Compartment Door
Latch
B-6
7
Tailgate Hinges .B-68

Brakes,
Adjust .B-41
Brake
Linings .B-42

Brake
Master Cylinder B-40
Charging
Circuit
B-l9
Clutch
. B-43, B-44
Cooling System—Radiator. B-28, B-29 Differentials
........
.B-50, B-51, B-52, B-53

Distributor
B-14, B-l5

Engine
Oil B-9
Engine
Oil
Filter
B-10, B-ll

Engine
Tune-Up B-20
Exhaust
Emission Control System
B-2
2

Exhaust
Manifold Heat Control Valve. . . .B-l2

Exhaust
System
B-2 3
Fan
Belt . .B-21
Front
Axle U-Joint B-54, B-55

Generator
.B-16
Headlights B-61
Heater Controls B-62
Lights
and Controls B-59 Positive Crankcase Ventilation Valve. . . .B-l3
Shock Absorbers B-48
Spark
Plugs. B-17
Speedometer Cable. .B-60

Spring
Bushings.. . .B-46

Spring
Shackles .B-47
Steering
Gear
B-2 7
B-l. GENERAL
All
'Jeep' Universal vehicles require periodic
lubri­

cation and other maintenance services for normal
vehicle
usage
and application to promote satis­ factory operation and prevent
excessive
wear. Un­
der severe operating or atmospheric conditions
these
services should be performed more
often
than
under normal conditions. It should also be remem­
bered that common short trips and
stop-and-go
driving
are more severe on lubrication
points
than
Starting
Circuit
B-l8

Tie
Rod and Drag
Link
Sockets
.
B-45

Tires
B-64

Transmission
and Transfer Case—
Lubricant
Level
Check B-30

General
B-31

Transfer
Case B-32
Transmission
.B-33

Transmission
and Transfer
Case
—

Lubricant
Change .B-34
General
.B-35

Transfer
Case B-36
Transmission
B-3
7, B-38

Transfer
Case Linkage B-39

Universal
Joints and Slip Joints.
.......
.B-58

Wheel
Bearings..
.........
. . .B-56, B-57
Windshield
Wiper and Washer B-63

LUBRICATION
OF

OPTIONAL EQUIPMENT
B-69
Centrifugal
Governor. .B-71
Pintle Hook .B-70

Powr-Lok
or
Trac-Lok
Differential B-72

PARTS REQUIRING
NO LUBRICATION.
. . .B-73

Alternator
Bearings. B-76
Clutch
Release Bearings.
.............
.B-74
Shock Absorbers B-78
Springs
B-7
7
Starter
Motor Bearings B-75

Water
Pump Bearings B-74

LUBRICATION REQUIREMENTS FOR OFF-HIGHWAY OPERATIONS
B-79

Air
Cleaner B-82

Chassis
Lubrication
B-83

Engine
Oil B-80
Engine
Oil
Filter
B-81
Differentials .B-86
Front
Axle U-Joints. B-84
Transfer
Case and Transmission .B-85
constant
speed
driving on highways, and even more
intensified in extreme cold or hot weather; there­ fore, vehicles driven under
these
conditions must
be lubricated and serviced more
often
than nor­ mally operated vehicles. The specifications of
types
and
amounts of lubricant given in the Lubrication

Chart
and
text
of this section should be closely
followed. The off-highway operation lubrication
notes,
given in the last part of the section, should
be followed when applicable. 7

B
LUBRICATION B-3.
SERVICE
MAINTENANCE
SCHEDULE

Perform
the following operations at the mileage shown. Two thousand miles equals
3,200
km.

SERVICE
MAINTENANCE
SCHEDULE

OPERATION
VEHICLE
^ n>
MILEAGE
IN
THOUSANDS

6 8 10 12 24 30
Check Wheel Nut Torque*
Check
Fluid
Level
in Battery X Check
Fluid
Level
in Brake Master Cylinder0. X
Service
Cooling
System X Service Tires X

Lubricate
Distributor
Cam Lubricator (F4-134) X
Lubricate
Steering Linkage X

Lubricate
Propeller Shaft Universal Joints X

Lubricate
Propeller Shaft
Slip
Joints ; X
Lubricate
Tie Rod and Drag
Link
Sockets................................... X Change Engine
Oil
and
Filter,
and Service Air Cleaner (F4 134 Engine)** X
Change Engine Oil and
Filter,
and Service Air Cleaner (V6-225 Engine)**....
Check Brake Operation and Pedal
Free
Play X Check
Clutch
Pedal
Free
Play. .... X
Check all
V-Belt
Tensions X
Check Exhaust Emission System
(If
so equipped)*** \ X
Service Positive
Crankcase
Vent
Valve
and Breather . .' X
Road Test
Including
a Check of all Instrument
Lights
and Controls X Tune-up Engine
Check Operation of
Manifold
Heat
Control
Valve

Clean
Exterior of Radiator

Align
Headlights • Check Brake
Linings
,
Check Exhaust System for Leaks Replace Canister Air
Filter
(F. E. E. C. System)
Check
Axle
U-Bolt
Torque. Check Lubricaunt
Level
of Front
Axle
Universal Joints
Check Shock Absorber Mountings and Bushings Check Front and
Rear
Spring Bushings

Lubricate
Distributor
(V6-225).
Replace Spark, Plugs
Check Charging and Starting Circuits
Lubricate
Tailgate Latch, Supports and Hinges.

Lubricate
Door and
Hood
Hinge Pivots ;
Lubricate
Glove Compartment Door Latch

Lubricate
Heater Controls •

Lubricate
Windshield
Wiper and Washer Controls
Clean,
Repack and
Adjust
Wheel Bearings
Change Transmission and Transfer Lubricant. .
Replace
Dry-Type
Air Cleaner • Check Lubricant
Level
of
Differential

Lubricate
Transfer
Case
Shift
LeArer
Control
C«se.
. , . . . . . . . .
Continuing
each
2,000 miles

Continuing
each
6,000 miles

Continuing
each
24,000 miles

X
Continuing
each
30,000 miles
•Check after the
first
200 miles [320
km.
J
of operation.
If
wheel or wheels are changed for any
reason,
have
wheel nut torque rechecked after an additional two hundred miles of operation
••Service mileage shown or every 60 days, whichever occurs
first.

•••Maintenance check on emission system must be performed per
information
in this manual. "See text for brakes.

"Nj
^Miles
2,000
6,000
12,000
18,000
24,000
30,000
Kilometers

3,200
9,600
19,200
28,800
38,400 48,000

B-9.
Engine Oil

For
maximum
engine
protection under all driving conditions encountered during the recommended

oil
change intervals, it is necessary to use only

"MS"
certified
sequence-tested
oils. The term
"MS"
must appear on the oil container singly or

in
conjunction with other designations. "MS" des­
ignated oils are heavy-duty detergent oils that are
formulated to withstand all service conditions in
modern powerplants. Engine oils designated only
as
"ML"
and/or
"MM"
are not recommended and should not be used except in an emergency when

"MS"
oil is not available. Certified
sequence-tested

engine
oils are described on their containers by

such
phrases as:
meets,
exceeds,
excels, or has
proven superior in the
test
requirements,
test
sequences, MS Service
tests,
standards, and service

requirements,
of automotive manufacturers, auto­
makers,
or car manufacturers for MS service or
Service
MS.
It
may be necessary to change
engine
oil more
frequently than normally recommended, depending upon the type and quality of oil used, the severity
of operation conditions, if the
engine
is used for
short
periods in cold weather, or if the
engine
is allowed to idle for excessive periods.

Always
drain
the crankcase while the
engine
is hot since
dirt
and contaminants are then more
likely
to be held in suspension and therefore
will

drain
out more completely.
Drain
the crankcase as follows:

a.
Position the
drain
receptacle under the
drain

plug.

b.
Remove the
drain
plug using the correct size

wrench.
Be careful of hot oil.
c.
Carefully
clean the
drain
plug. Inspect and

replace
the gasket, if deteriorated.
d.
When the oil has drained, replace and tighten
the crankcase
drain
plug. 12

LUBRICATION

vital
to the life of the
engine.
When the vehicle
is operated under abnormal conditions, (for ex­
ample when driven on secondary roads or through
fields) then service of the air cleaner must be more frequent

Note:
Under extreme continually dusty and dirty
conditions where the vehicle operates in clouds of dust and
dirt,
service the air cleaner daily.

a.
To service the air cleaner on vehicles equipped
with the
Hurricane
F4
engine
(Fig. B-5) unscrew
the eye
bolt
on the oil cup clamp and remove the

oil
cup from the cleaner body. Remove the oil from the cup and scrape all
dirt
from the inside, wash cup clean using a cleaning solution if neces­

sary.
In summer
refill
the oil cup with IV2 pints [0,6 ltrs.] of
SAE-40
or 50 grade
engine
oil. In
winter
refill
using grade
SAE-20
engine
oil. For
servicing the air cleaner
body
(less
oil cup),
loosen

hose
clamp and remove
hose
from the cleaner. Detach breather
hose
from the fitting on the cleaner. Remove the two wing screws and lift the
cleaner from the vehicle. Agitate the cleaner
body

thoroughly in cleaning solution to clean the filtering

element.
Dry
element
with low pressure com­ pressed air. Reinstall the cleaner
body
and replace
the oil cup. Service the air cleaner every
2000
miles
[3.200
km.].
b. To service the oil bath air cleaner on vehicle
equipped with the Dauntless V-6
engine
(Fig. B-6),

first
remove the air cleaner from the carburetor
by unscrewing the wing nut. Remove the oil cup
FIG.
B-5—OIL
BATH AIR
CLEANER
-
HURRICANE F4 ENGINE 1—
Horn
7—Clamp
2—
Flexible
Connector
8—Oil
Cup
3—
Hon
Clamp
9—Clamp

A—Carburetor
Vent Tube 10—Hose 5— Body 11—Clamp
6—
Screw
and
Lock
Washer 13—Gasket
FIG.

B-6—OIL BATH AIR
CLEANER
-
DAUNTLESS V-6 ENGINE

1—WinB
Nut
2—
Cover

3—
Rubber
Gasket
4—
Cork
Gasket
5—
Oil
Cup 6—
Breather

7—
Clamp

8—
Vent
Tube 9—
Air
Pump Hose from cleaner
body
and remove the oil from the cup,
scrape all
dirt
from the inside.
Clean
oil cup thor­
oughly, wash filter
element
in a solvent that
will
leave it clean and dry.
Fill
oil cup to indicated
level with clean
S.A.E.
40 or 50 grade
engine
oil
(S.A.E.
20 grade in winter.) Assemble cleaner filter

element
to oil cup making sure that gasket is in
place
between
the two pieces. Assemble air cleaner assembly to carburetor making sure the gasket
be­

tween
air cleaner and carburetor is in place. Secure

air
cleaner to carburetor with wing nut. Service the

air
cleaner every
6000
miles
[9.600
km.],
c.
Carefully
check the
hose
clamps and
fittings
on
the breather
hoses
at frequent intervals. Loose con­nections
will
affect proper operation of the
crank­

case ventilating system.

B-26. Dry-Type
Air Cleaner Service the air cleaner on Dauntless V-6
engines

at each oil change under normal driving conditions.

If
the vehicle is operated under dusty conditions,
check the condition of the air cleaner
element
more
frequently and service if dirty.

Servicing
the air cleaner consists of cleaning or replacing the air cleaner
element
and replacing the

crankcase
ventilation filter (breather assembly). See Fig. B-7.

The
air cleaner
element
assembly consists of a
paper
element
and a polyurethane
element
The
paper
element
cannot be cleaned.

To
clean the polyurethane
element,
first carefullly remove it from the paper
element
Then
wash it in 14

B

LUBRICATION
B-72.
Powr-Lok
or Trac-Lok
Differential

Refer
to Par. B-53.

B-73.
PARTS
REQUIRING
NO
LUBRICATION

B-74.
Water Pump Bearing,
Clutch
Release
Bearing

The
water pump and clutch release bearings are

prelubricated
for life when manufactured and cannot be relubricated.

B-7S.
Starter
Motor
Bearings

The
starting motor bearings are lubricated at assembly to last
between
normal rebuild periods.

B-76.
Alternator Bearings

The
alternator bearings are lubricated at assembly

and
require no further lubrication.

B-77.
Springs

The
vehicle springs should not be lubricated. At assembly the leaves are coated with a long-lasting

special
lubricant which is designed to last the life
of the springs. Spraying with the usual mixture of
oil
and kerosene has a tendency to wash this
lubri­

cant
from
between
the leaves, making it necessary
to relubricate
often
to eliminate squeaking.

B-78.
Shock Absorbers

Hydraulic
direct-action shock absorbers are per­ manently sealed and require no periodic
lubrica­

tion service. Shock absorber mounting bushings
are
not to be lubricated.

B-79.
LUBRICATION
REQUIREMENTS
FOR
OFF-HIGHWAY
OPERATION

Adequate lubrication
becomes
increasingly im­ portant when vehicles are used in off-highway
operation. Under
these
conditions all operating
parts
of both the
engine
and chassis are subjected
to unusual pressures. At the same time such operation is usually under abnormal dust and
dirt

conditions making additional precautions neces­

sary.
The importance of correct lubrication for
the conditions of operation cannot be overestimated.

B-80.
Engine
Oil

It
is important, that the oil in a new or rebuilt
engine
be changed after the first
eight
or ten hours
of operation, and for heavy, dusty work, every 50

hours
thereafter. Watch the condition of the oil closely and change it immediately if it appears to
be contaminated.

i-Il.
Engine
Oil
Filter

Replace
the oil filter at the end of the first 100

hours
of service. Under extreme operating con­ ditions, more frequent replacement may be re­
quired.
The condition of the oil is a reliable

indicator
of the condition of the filter element.
If
the oil
becomes
discolored and shows evidence
of contamination, change the filter without delay.
(Refer
to
Par.
B-10, B-ll for the correct procedure
for replacing the oil filter.)

B-82.
Air Cleaner

Care
of the air cleaner is extremely vital to the life of the engine. Pay particular attention to the
amount of dust and
dirt
in the air taken into the

engine
through the air cleaner. When dust is not
noticeable in the air, service the air cleaner each scheduled maintenance period. Whenever the air is
noticeably dusty (for example when the vehicle is

driven
on secondary roads or through fields) then
service the air cleaner more frequently. Under extreme continually dusty and dirty conditions
where the vehicle operates in clouds of dust and

dirt,
service the air cleaner daily. (Refer to Par.
B-24
thru
B-26 for service procedures.)

B-83.
Chassis
Lubrication

The
period of lubrication depends entirely upon the type of work being done. Using the specified

interval
given in the Service Maintenance Schedule as a guide, lubricate at safe intervals required for
the particular type of operation. Under extremely
dusty conditions lubricate
these
points daily. Be

sure
to force enough lubricant into each fitting to force out the old lubricant which might be con­
taminated with grit and which would cause
rapid

wear
if allowed to remain.
Do not place lubricant on the various
ball
and socket joints or pivot points of the lift linkage as
dirt
will
accumulate to form an abrasive mix­

ture.
It is
best
to simply wipe
these
parts clean

with
a cloth.

B-84.
Front
Axle
Shaft Universal Joints

For
off-highway use remove the universal joints twice yearly, thoroughly clean both the housings

and
joints with a suitable solvent, and
refill
the
housings to the
fill
plug opening levels with the

correct
lubricant as given in the
Lubrication
Specifications.

B-85.
Transmission and Transfer
Case

The
combined capacity of the two housings is
small
for economy, making it important that the

lubricant
be changed at regular intervals. For off-highway use
drain
both housings every 300

hours
of operation and
refill
to the
fill
plug opening
levels. Refer to B-35 through B-37 when changing

lubricant.

B-86.
Front and
Rear
Axle
Differentials

Because of the higher pressure developed in the
axle assemblies with heavy duty operation,
drain,

flush,
and
refill
the differential assemblies each 300 hours of operation. Use only flushing oil or light
engine
oil to clean out the housings (except

Powr-Lok
and
Trac-Lok
differentials). Refer to
Par.
B-52 and B-53 for draining and flushing

differential.
18

Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

c
TUNE-UP

Contents

SUBJECT
PAR.

GENERAL
C-l

TUNE-UP
.C-2
Air
Cleaner
C-21

Battery
. C-3
Carburetor
Adjustments
C-2 5

Coil
C-20
Crankcase
Ventilation C-6

Cylinder
Compression C-9

Cylinder
Head(s) .C-5

Dash
Pot Adjustments .C-26

Distributor
Service C-10
thru
C-13

Distributor
Resistance Test C-l6

Fan
Belt
C-2 7
Fuel
Lines
and Screens
C-2
2

C-l.
GENERAL
An
engine tune-up should be performed for all
Jeep Vehicles each 6000 miles [9.600 km.] or at the end of each 250 hours off-the-road operation,
to ensure best possible performance at all times.
The
tune-up should follow the sequence given in
this section.
Because of federal laws limiting exhaust emissions,

it
is even more important that the engine tune-up is
done
accurately, using the specifications listed
on the tune-up sticker found in each engine com­

partment.

Note;
To ensure proper operation and effectiveness
of the exhaust emission control system, and to
comply with
Federal
and State requirements, a
recheck
of ignition timing, idle speed and idle mix­

ture
and necessary adjustments must be performed
after the first
2,000
miles [3.200 km.] of vehicle
operation.

A
minor engine tune-up should be performed every
6,000
miles [9.600 km.] or at the end of 250 hours
of off-the-road use.
Major
engine tune-up should
be performed every 12,000 miles [19.300 km.].

The
parts of units which affect power and perform­
ance may be divided into three groups:
(1) Units affecting compression
(2) Units affecting ignition
(3) Units affecting carburetion

The
tune-up procedure should cover
these
groups
in
the order given. While the items affecting com­
pression and ignition may be handled according
to personal preference, correction of items in the
carburetion
group should not be attempted until

all
items affecting compression and ignition have
been satisfactorily corrected.

Note:
To make sure hydro-carbon and carbon
monoxide emissions
will
be within limits, it is very

impotrant
that the adjustments be followed exactly
as listed on the sticker found in each engine compartment.
SUBJECT
PAR.

Fuel
Pump . . C-23

Heat
Control
Valve C-7

Ignition
Cables C-19

Ignition
Timing
. C-14

Ignition
Wires C-l8

Manifold
C-5

Manifold
Vacuum C-24

Point
Dwell C-17

Primary
Circuit
Tests
.................
C-15
Spark
Plugs C-4

Tappets
C-8

ROAD TEST C-2
8

SERVICE
DIAGNOSIS
. : C-29

TUNE-UP SPECIFICATIONS..
C-30

Minor
engine tune-up consists of the following.
Inspect
and correct as required:
Battery
cables and connections.
Alternator
and regulator wiring.

Primary
— Secondary wiring, distributor cap.

Cylinder
head torque.

Contact
point dwell.

Vacuum
and centrifugal advance.

Ignition
timing.
Spark
plugs for correct air gap.

Adjust
idle speed and idle air mixture.

Adjust
all drive belt tensions.
Clean
carburetor air cleaner.

Lubricate
exhaust manifold damper.

Major
engine tune-up includes the following.
Inspect
and correct as required:
Battery
condition and charging
circuit.
Clean,
lubricate
and tighten battery cable connec­
tions.

Ingition
system.
Spark
plugs; replace if necessary or clean and gap.

Compression
check.

Primary—Secondary
wiring, distributor cap.

Replace
contact points and condenser.

Lubricate
distributor cam with cam grease.
Adjust
contact points.

Check
vacuum and centrifugal advance. Set ignition timing.

Torque
cylinder head.
Adjust
idle speed and idle air mixture.

Replace
fuel filter element (every 12,000 miles [19.300
km.]).

Adjust
all drive belt tensions.

IMPORTANT: SPECIFICATIONS
FOR EN-

GINE
RPM.
DISTRIBUTOR POINT DWELL,
AND IGNITION TIMING GIVEN
IN
TUNE- UP SECTION
C
REFER
TO
VEHICLES
WITH
AND WITHOUT EXHAUST EMISSION CON­

TROL
SYSTEMS.

FOR
VEHICLES
EQUIPPED WITH EXHAUST
EMISSION CONTROL SYSTEMS ALSO
REFER
TO
SECTION
Fl (F4-134
ENGINE)
AND
F2 (V6-225
ENGINE).
19

c

TUNE-UP
C-2.
TUNE-UP SEQUENCE

The
following
Pars.
C-3 through
C-2
7
give the
sequence and describe the services to be performed
when tuning the engine.

C-3.
Clean
and
Check
Battery
Inspect
battery and cables. If the battery is not
satisfactory, install a fully-charged battery to allow
completion of the tune-up.
Note: If the battery fails any of the following tests,
remember that the cause may be other electrical
trouble, and not necessarily only a defective battery.
Refer
to Section H for electrical troubleshooting

and
tests.

a.
Check
the specific gravity of the eletrolyte in
each cell of the battery. A hydrometer reading of 1.260 indicates that the battery is fully charged.

If
the reading is 1.225 or below, the battery
needs

recharging.
If one or more cells is 25 "points" (.025)

or
more lower than the other cells, this indicates
that the cell is shorted, the cell is about to
fail,
or
there is a
crack
in the battery partition in the case.
Unless the battery is repaired or replaced, battery trouble
will
soon be experienced.

b.
Check
the electrolyte level in each cell, add

distilled
water to maintain the solution %" [9.5
mm.] above the plates. Avoid overfilling. Replace
the filler caps and tighten securely. It is important
to keep the electrolyte level above the plates at
all
times because plates that are exposed for any
length of time
will
be seriously damaged.

c.
Check
the wing nuts on the hold-down frame
for tightness. Tighten them only with finger pres­

sure,
never with pliers or a wrench. Excessive pres­

sure
could damage the battery case.

d.
Clean
the battery terminals and cable connec-
FIG.
C-l—FRAME
GROUND
STRAP
—

HURRICANE
F4
1—
Right
Front
Engine Mount

2—
Frame
Ground
Strap
DAUNTLESS
V-6
tors.
Prepare a strong solution of baking soda and

water
and brush it around the terminals to remove

any
corrosion that is present. The cell caps must
be tight and their vents sealed to prevent cleaning
solution entering the cells. After cleaning install
cable connectors on terminals and coat the ter­
minals
and connectors with heavy grease.
e. Inspect the battery cables and replace if badly

corroded
or frayed.
Check
tightness of terminal
screws to ensure
good
electrical connections.
Check

the tightness of the negative ground cable connec­ tion at the engine to ensure a
good
ground con­ nection.

f.
Load
test
the battery. Connect a voltmeter across the battery. Run the starting motor for 15 seconds.
If
the voltage
does
not drop below 10 volts on a 12 volt battery the battery is satisfactory. If the
voltage falls below
these
values, yet the specific
gravity
is above
1.225,
the condition of the battery
is questionable.

g.
Make sure the engine to frame ground strap or
cable connections are tight. If
these
connections
are
loose,
corroded or dirty,
hard
starting or failure
of the vehicle electrical system may result. Refer
to
Fig.
C-l
for location of the
Hurricane
F4 engine
to frame ground strap and its connections. Refer to Fig. C-2 for location of the Dauntless V-6 en­ gine to frame ground cable.

C-4.
Clean and
Adjust
Spark Plugs
Clean,
inspect, and gap
spark
plugs. Do not install

spark
plugs until completion of compression tests.

a.
Use a
Spark
Cable
and Installing
Plier
Tool,

W-2
74,
to remove the leads from the
spark
plugs.

Caution:
Pulling on the cables to remove them

from
the
spark
plugs can cause internal breaks in
the leads that
will
cause ignition failure.

b.
Using a
spark
plug wrench, loosen each
spark

plug one or two turns to break
loose
any carbon
deposits on the plug base. 20

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

FIG.
C-3—SETTING SPARK PLUG
GAP
1—Wire
Gauge 2—Spark Plug
c.
Blow out all carbon and
dirt
from each
spark

plug hole with compressed air. If compressed air is
not available, start the engine and accelerate to 1000 rpm. to blow out the carbon and
dirt.
Stop
the engine.

d.
Remove the plugs carefully with a
spark
plug

wrench.

e. Inspect the plugs for serviceability. Especially
check
for burned and eroded electrodes, blistering
of porcelain at the firing tip, cracked porcelain, or

black
deposits and fouling. These conditions in­
dicate that the plugs have not been operating at
the correct temperature. Replace bad or worn plugs

in
sets.
f. Measure the electrode gap of each new or exist­
ing plug with a wire
gauge
as shown in Fig. C-3.

Adjust
each electrode gap to the specific gap by
bending the outer electrode mounted in the plug
shell.

g.
Clean
the plugs on a sand blast cleaner. Avoid
too much abrasive blast as it
will
erode the in­
sulator.
Clean
the threads with a wire
brush.

Deposits
will
retard
heat flow to the cylinder head.

h.
Clean
the electrode surfaces with a small flat
file. Dress the electrodes to secure flat parallel surfaces on both the center and side electrode.

i.
Champion J-8 are the replacement
spark
plugs
recommended for the F4-134 engine. Adjust elec­
trode gap to .030" [0,762 mm.] and should be
torqued to 25 to 33 lb-ft. [3,5 a 4,6 kg-m.].

j.
For the V6-225 engine, AC 44S or Champion

UJ12Y
spark
plugs are the replacement
spark

plugs recommended. The
spark
plugs should be gapped to .035" [0,889 mm.] and should be
torqued to 25 to 33 lb-ft. [3,5 a 4,6 kg-m.].
C-5. Torque Cylinder
Head(s)
and
Manifold
a.
Hurricane
F4 Engine.

Torque
the cylinder head bolts with a torque

wrench
to 60 to 70 lb-ft [8,3 a 9,7 kg-m.]. Follow
the sequence shown in Fig. C-4. Do not overlook
tightening the cylinder head bolt, No. 5, in the

intake
manifold directly under the carburetor
opening. 10102

FIG.
C-4—HURRICANE
F4
ENGINE CYLINDER HEAD BOLT TIGHTENING SEQUENCE
Torque
all manifold attaching nuts evenly to 29
to 33 lb-ft. [4,0 a 4,6 kg-m.].
b.
Dauntless V-6 Engine.

Torque
cylinder head bolts 65 to 85 lb-ft. [9,0 a 11,8 kg-m.]. Follow the sequence shown in Fig.

C-5.
Torque all intake manifold bolts 45 to 55 lb-ft. [6,2 a 7,6 kg-m.]. Torque all exhaust manifold bolts
15 to 20 lb-ft. [2,1 a 2,8 kg-m.]. Refer to Fig. Dl-
for tightening sequence. 14203

FIG.
C-5—DAUNTLESS
V-6
ENGINE CYLINDER HEAD BOLT TIGHTENING SEQUENCE C-6.
Service
Crankcase
Ventilating System

•
Refer to Fig. C-6 and C-7.
Positive crankcase ventilation is accomplished by

utilizing
the vacuum created in the intake mani­
fold to draw clean air through the crankcase and
valve chamber. A valve, in the vacuum line to the

intake
manifold, varies the air flow through the

crankcase
to
meet
changing conditions at all engine

speeds
and loads. The system
will
work effectively as long as all component parts are clean and free

from
sludge and carbon. Improper operation of the ventilating system can contribute to rough
idling,
power loss, and the formation of sludge and

varnish
in the engine.

The
system also prevents crankcase vapors from
entering the atmosphere. Engine vapors are drawn
into the carburetor through the ventilation valve
and
burned with the normal fuel mixture. 21

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

C The
valve, connecting pipes, and
hoses
must be
inspected and serviced at intervals of
2,000
[3.200

km.],
6,000
[9.600 km.] and 12,000 [19.300 km.]
miles, continuing each
6,000
miles [9.600 km.] of
vehicle operation thereafter. It may be necessary to inspect and clean the system more frequently

under
adverse driving or weather conditions.
Replace
the valve each 12,000 miles [19.300 km.],

a.
Dauntless V-6 Engine.

Filtered
air from the carburetor air cleaner enters the engine crankcase through a hose. The ventila­tion valve is mounted on the right cylinder bank
rocker
arm cover (Fig. C-7) and is connected by a

hose
to a fitting at the base of the carburetor at the

intake
manifold opening. The valve varies the air
flow through the crankcase to
meet
changing condi­
tions at all engine
speeds
and loads. To check the operation of the system, remove the valve with the

hose
attached from the rocker arm cover.
With
the engine running at fast idle, a vacuum must be felt
at the open end of the ventilation valve. If no

vacuum
is present, the valve and
hose
should be
inspected and cause of the restriction determined.

To
check the valve disconnect it from the air
13334

FIG.
C-9—POSITIVE CRANKCASE VENTILATION SYSTEM
— F4
ENGINE (TYPICAL)
1—Valve
Open 2—Valve Closed
23