2023 TOYOTA YARIS CROSS brake

315
4
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
Driving
■If you feel that the vehicle is approaching close to a surround-
ing vehicle, object, person, or gut- ter
Depress the brake pedal to stop the
vehicle and then change the shift posi- tion to change the direction of travel of the vehicle. At this time, assist will be
suspended. However, if the “Start” but- ton is selected, assist will resume and the vehicle will move in the direction cor-
responding to the selected shift position.
■Parallel parking departure function
●While assistance is operating, if the
driver determines that the vehicle can depart from the parking space and operates the steering wheel, assis-
tance will be end at that position.
●Do not use parallel parking departure
function in any situation other than when departing a parallel parking spot. If assistance is started uninten-
tionally, depress the brake pedal and stop the vehicle, then press the Advanced Park main switch to cancel
assistance.
■Situations in which the parallel parking departure function will not operate
In situations such as the following, the parallel parking departure function will
not operate:
●When vehicles waiting at a traffic sig-
nal in the departure direction
●When a vehicle is stopped in the area
behind where the vehicle will depart
●When a wall, column, or person is
detected near a front or rear side sen- sor
●When the vehicle has been parked on a curb and a side sensor detects the road surface
●When a vehicle is not parked in front of the vehicle
●When there is excessive space between the front of the vehicle and a
parked vehicle
■Function description
The memory function can be used
to park in a previously registered
parking space, even if there are no
parking space box or adjacent
parked vehicles.
Memory function

317
4
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
Driving
begin operating.
When the brake pedal is
released, “Moving Forward...”
will be displayed and the vehicle
will begin moving forward.
If you feel that the vehicle is approach-
ing close to a surrounding vehicle,
object, person, or gutter: P. 3 1 8
6Perform operations as indicated
by the advice displays until the
vehicle stops in the target park-
ing space.
7 When the vehicle is stopped,
shift the lever to P.
8 Check the position that the vehi-
cle has stopped. If necessary,
adjust the position of the parking
spot to be registered using the
arrow buttons, and then select
“Registration” button.
“Registration Completed” will be dis- played on the multimedia system
screen.
 Register the parking space only
if there are no obstructions within
the area shown by the thick
lines.
 The amount that the position of
the parking spot to be registered
can be adjusted is limited.
■When parking in a parking
space registered to the mem-
ory function
1 Stop the vehicle at a position
perpendicular to the center of
the target parking space.
Approximately 1 m (3.3 ft.)
2 Press the Advanced Park main
switch and check that a possible

318
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
parking space is displayed on
the multimedia display.
3 If the “MODE” button is dis-
played, select it to change to the
memory function.
4 Select the desired parking
space, and then select “Start”
button.
Perform the procedure for the per-
pendicular parking function from
step 3. (P.308)
■If you feel that the vehicle is approaching close to a surround-
ing vehicle, object, person, or gut- ter
Depress the brake pedal to stop the
vehicle and then change the shift posi- tion to change the direction of travel of the vehicle. At this time, assist will be
suspended. However, if the “Start” but- ton is selected, assist will resume and the vehicle will move in the direction cor-
responding to the selected shift position.
■When overwriting a registered parking space
If the maximum number of parking
spaces have been registered and is
selected, a registered parking space can
be selected and then overwritten with a
new parking space.
■When multiple parking spaces are registered
Select the desired parking space, and
then select “Start” button.
NOTICE
■When using the memory function
●The memory function is a function
which provides assistance in park- ing in a previously registered park-ing space. If the condition of the
road surface, vehicle, or surround- ing area differs from when registra-tion was performed, the parking
space may not be able to be detected correctly or assistance may not be provided to the point
that the vehicle is fully parked.
●Do not register a parking space in
situations such as the following, as the set parking space may not be able to be registered or assistance
may not be possible later.
• When a camera lens is dirty
• When it is raining or snowing

320
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
■Assistance will be canceled
when
In situations such as the following,
Advanced Park operation will be
canceled.
Firmly hold the steering wheel and
depress the brake pedal to stop the
vehicle.
As system operation has been can-
celed, begin the operation again or con-
tinue parking manually, using the
steering wheel.
 The Advanced Park main switch
is pressed
 The shift position has been
changed to P
 The parking brake is engaged
 A door is opened
 The driver’s seat belt is unfas-
tened
 The outside rear view mirrors are
folded
 The TRC or VSC is turned off
 The TRC, VSC or ABS operates
 The power switch is pushed
 The system determines assis-
tance cannot be continued in the
current parking environment
 The system malfunctions
■Assistance will be suspended
when
In situations such as the following,
Advanced Park operation will be
suspended.
Assistance can be started again by fol-
lowing the directions displayed on the
center display.
 The steering wheel is operated
 The accelerator pedal is
depressed
 The shift lever has been oper-
ated
 Brake control operates
 The PCS (Pre-Collision System)
has operates
NOTICE
• When a camera lens is dirty or cov- ered with water droplets
If assistance is ended during registra- tion, perform registration again.
●When registering a parking space to the memory function, if the road
surface cannot be detected “No available parking space to register” will be displayed.
●When using the memory function, stop the vehicle directly beside the
space where it desired to be stopped. Otherwise the parking space may not be able to be
detected correctly and assistance may not be provided to the point that the vehicle is fully parked.
●Do not use the memory function if a camera has been subjected to a
strong impact or images of the pan- oramic view monitor are mis-aligned.
●If a camera has been replaced, as the installation angle of the camera
will have changed, it will be neces- sary to reregister parking spaces of the memory function.
Advanced Park cancel-
ation/suspension

322
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
■If “Unavailable in current condi-
tion” is displayed
Move the vehicle to another location and use the system.
■If “Not enough space to exit” is dis-
played
The parallel parking departure function cannot be used due to a situation such
as the distance between your vehicle and vehicles parked in front of and behind your vehicle being short, the
existence of an object in the departure direction, etc.
Check the conditions of the area around
your vehicle and depart from the parking space manually.
■If “Cannot control speed” is dis-played
The system judged that it cannot adjust the speed of the vehicle when using the system in an area with a slope or step
and assistance was canceled.
Use the system in a level location.
■If “Obstacle detected” is displayed
The PKSB (Parking Support Brake)
( P.291) has operated, and assistance was canceled.
Check the condition of the surrounding
area. To resume assistance, select the “Start” button on the center display.
■If “No available parking space to register” is displayed
This message is displayed when is
selected at a parking space that cannot
be detected.
Operate the system at a parking space
where differences in the road surface can be recognized. ( P.316)
Each time the switch is pressed,
the system changes between
power mode, normal mode, and
ECO drive mode.
Typ e A
Typ e B
1 Normal mode
Provides an optimal balance of fuel
economy, quietness, and dynamic per-
formance. Suitable for normal driving.
2 Power mode
Controls the transmission and engine to
Driving mode select
switch
The driving modes can be
selected to suit driving condi-
tion.
Selecting a drive mode

323
4
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
Driving
provide quick, powerful acceleration.
Making it suitable for when agile driving
response is desired, such as when driv-
ing on roads with many curves.
When the Power mode is selected,
Power mode indicator comes on.
3 Eco drive mode
Helps the driver accelerate in an eco-
friendly manner and improve fuel econ-
omy through moderate throttle charac-
teristics and by controlling the operation
of the air conditioning system (heat-
ing/cooling).
When the Eco drive mode is selected,
Eco drive mode indicator comes on.
■Operation of the air conditioning system in Eco drive mode
Eco drive mode controls the heat- ing/cooling operations and fan speed of the air conditioning system to enhance
fuel efficiency. To improve air condition- ing performance, perform the following operations:
●Turn off air conditioning eco mode ( P.342)
●Adjust the fan speed (P.343)
●Turn off Eco drive mode
■Automatic deactivation of Power mode
If the power switch is turned off after
driving in power mode, the drive mode will be changed to normal mode.
Trail Mode (AWD vehi-
cles)
Trail Mode is designed to con-
trol the spinning of the drive
wheels by integratedly con-
trolling AWD, brake and drive
force control systems. Use the
Trail Mode when driving
bumpy roads, etc.
WARNING
■Before using Trail Mode
Make sure to observe the following
precautions.Failure to observe these precautions may result in an unex-pected accident.
●Trail mode is intended for use when driving on rough roads.
●Check that the Trail Mode indicator is illuminated before driving.
●Trail Mode is not intended to expand the limits of the vehicle. Thoroughly check the road condi-
tions and drive with caution.
NOTICE
■I n o rd e r t o e n su re t h a t Trai l M o de operates properly
Do not continuously use the Trail
Mode for a long period of time. Depending on the driving conditions, the load on related parts increases
and the system may not operate prop- erly.

325
4
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
Driving
1Switches to Snow mode
2 Switches to Normal mode
3 Switches to Trail mode
( P.323)
■Canceling the snow mode
Snow mode is automatically canceled
when the power switch is turned off or Trail Mode is selected.
Press the “DAC” switch.
The downhill assist control system indi-
cator will come on and the system will
operate.
When the system is in operation, the
slip indicator will flash, and the stop
lights/high mounted stop lights will be
lit. A sound may also occur during the
operation. This does not indicated a
malfunction.
Snow mode (AWD vehi-
cles)
Snow mode can be selected to
suit the conditions when driv-
ing on slippery road surfaces,
such as on snow.
System operation
Downhill assist control
system (AWD vehicles)
The downhill assist control
system helps to prevent exces-
sive speed on steep downhill
slopes.
The system will operate when
the vehicle is traveling under
30 km/h (18 mph) with the
accelerator and brake pedals
released.
WARNING
■When using downhill assist con- trol system
Do not rely overmuch on the downhill assist control system. This function does not extend the vehicle’s perfor-
mance limitations. Always thoroughly check the road conditions, and drive safely.
System operation

326
Owners Manual_Europe_M52N75_en
4-5. Using the driving support systems
Press the “DAC” switch while the
system is in operation.
The downhill assist control system indi-
cator will flash as the system gradually
ceases operation, and will turn off when
the system is fully off.
Press the “DAC” switch while the down-
hill assist control system indicator is
flashing to start the system again.
■Operating tips
The system will operate when the shift lever is in a position other than P.
■If the downhill assist control sys-tem indicator flashes
●In the following situations, the indica-tor flashes and the system will not
operate: • The shift lever is in P.• The accelerator or brake pedal is
depressed. • The vehicle speed exceeds approxi-mately 30 km/h (18 mph).
• The brake system overheats.
●In the following situation, the indicator flashes to alert the driver, but the sys-tem will operate:
• The shift lever is in N. • The “DAC” switch is turned off while the system is operating.
The system will gradually ceases opera- tion. The indicator will flash during oper-ation, and then go off when the system
is fully off.
■When the downhill assist control
system is operated continuously
This may cause the brake actuator to overheat. In this case, the downhill
assist control system will stop operating, a buzzer will sound and the downhill assist control system indicator will start
flashing, and “Traction Control Turned OFF” will be shown on the multi-infor-mation display. Refrain from using the
system until the downhill assist control system indicator stays on and “Traction Control Turned OFF” the message goes
off. (The vehicle can be driven normally during this time.)
■Sounds and vibrations caused by the downhill assist control system
●A sound may be heard from the engine compartment when the hybrid
system is started or just after the vehi- cle begins to move. This sound does not indicate that a malfunction has
occurred in downhill assist control system.
●Either of the following conditions may occur when the downhill assist control system is operating. None of these
are indicators that a malfunction has occurred.• Vibrations may be felt through the
vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop.
■System malfunction
In the following cases, have your vehicle checked by any authorized Toyota retailer or Toyota authorized repairer, or
any reliable repairer.
●The downhill assist control system
indicator does not come on when the power switch is turned to ON.
●The downhill assist control system indicator does not come on when the “DAC” switch is pressed.
●The slip indicator light comes on.
Turning off the system