2022 TOYOTA GR86 stop start

142-1. Basic information before operation
2-1.Basic information before operation
After a few seconds, the “CAU-
TION” screen w ill be displayed.
Selecting “I Agree”, the caution
screen switches to the next screen.
This system reminds users when to
replace certain parts or compo-
nents on the screen.
When the vehicle reaches a previ-
ously set driving distance or date,
the maintenance remainder screen
will be displayed when the system
is turned on.
 To register maintenance informa-
tion: P. 3 8
If the touch screens become unre-
sponsive during operation or if any
other system error occurs, the sys-
tem can be restarted.
1 Press and hold the “VOLUME”
knob for 10 seconds or longer.Initial screen
When the engine switch is
changed to ACC or ON, the ini-
tial screen will be displayed
and the system will begin oper-
ating.
Caution screen
WA R N I N G
●When the vehicle is stopped with the engine running, always apply
the parking brake for safety.
Maintenance information
Restarting the system

343-2. Other settings
The system can connect to a
Wi-Fi® network that supports the
following standards.
 Communication standards:
•802.11b
•802.11g
• 802.11n (2.4GHz)
 Security:
•WPATM
•WPA2TM
●WPA and WPA2 are registered mark
of the Wi-Fi Alliance®.
Please ask your dealer to update
the system software*1.
You may also update the system
software via Wi-Fi®. The update
process involves downloading and
installing a software update*2. Note
that system functionality will be
restricted during installation.
*1: Please check with your dealer for
specific details on the update con-
tent.
*2: Depending on the software update
content, your radio station presets
and volume settings may be reset by
the update process.
●Update using Wi-Fi® may not be avail-
able in some countries.
1 Press the button.
2 Select “Settings”.
3 Select “General”.
4 Select “Clock”.
5 Select “Time Setting”.
6 Select “Sync With Phone”.
7 Connect to a Wi-Fi® network.
( P. 3 2 )
8 Display the general settings
screen. ( P. 2 9 )
9 Select “Software Update”.
10 Select “Update”.
11 Select “Check for Updates”.
 “Cancel”: Select to stop checking
for available updates.
 If “Automatically Check for
Updates” is on, updates will
automatically be checked for
and, if availabl e, a message will
be displayed. If a message is
displayed, select “OK” and pro-
ceed to the next step.
 If “Automatically Download
Updates” is on, updates will
automatically be downloaded.
After the download has com-
pleted, a message will be dis-
played. Select “OK” to start
installation and proceed to STEP
3 in “Update installation”.
( P. 3 5 )
Supported Wi-Fi® network
specifications
Updating the system
Download update

35
3
3-2. Other settings
Settings
12 Select “Download Now” to begin
downloading the update (if avail-
able).
 “Cancel”: Select to stop the
update process.
 The download status progress is
displayed in the category area.
 If the update procedure fails,
refer to the “Troubleshooting”
section. ( P. 9 6 )
1 Download any available
updates.
2 Select “Install Now” to start
installing the update.
 Installation will take several min-
utes.
●During software update installation, the screen may flicker. However, this
is not a malfunction.
3 When installation is complete,
select “OK” on the confirmation
message to complete the
update process.
 If the update procedure fails,
refer to the “Troubleshooting”
section. ( P. 9 6 )
4 Turn the engine switch to Off.
5 Open the driver’s side door.
6 Close the door.
7 Wait for 3 minutes or more.
8 Start the engine.
 The new software will be applied.
Update installation
NOTICE
●Park your vehicle in a safe place
when installing the update.
●The following system functions are
restricted during the update installa-
tion.
• It will not be possible to use general
system functions.
• Only the rear view camera image
will be displayed. Or the image will
disappear temporarily.

646-1. Basic operation
6-1.Basic operation
“VOLUME” knob: Press and hold
until a message is displayed, and
then select “OK” or wait a few
seconds for the audio/visual sys-
tem to turn off. Press and hold to
turn the system on again. The
system will turn on with the last
audio source used. Turn this
knob to adjust the volume. Press
to mute the audio/visual system.
 button: Press to display
screen buttons for the radio.
●The audio/visual system will remain off if you change the position of
engine switch Off to ACC/ON while
the audio/visual system is off. If you had set the volume to mute, the
audio/visual system will remain mute
and the track will start playing from where it was last stopped.
1 Press the button and select
the “Media”, or press the
button.
2 Select the desired audio source.
Media screen
Radio screen
 Each time button is
pressed, the radio modes can
also be changed.
Some basics
This section describes some of
the basic features of the
audio/visual system. Some
information may not pertain to
your system.
Your audio/visual system
works when the engine switch
is changed to ACC or ON.
NOTICE
●To prevent the 12-volt battery from
being discharged, do not leave the
audio/visual system on longer than necessary when the engine is not
running.
Turning the system on and
off
Selecting an audio source

1008-1. What to do if...
In other situations
*: For details, refer to the owner’s manual that came with the mobile phone.
If a problem occurs when attempting to perform a system update, refer to
the following table.
SymptomLikely causeSolution
Page
Mobile
phone
This
system
Even though all
conceivable meas-
ures have been
taken, the symptom
status does not
change.
The mobile phone is
not close enough to
this system.
Bring the mobile
phone closer to this
system.
--
The mobile phone is
the most likely
cause of the symp-
tom.
Turn the mobile
phone off, remove
and reinstall the bat-
tery pack, and then
restart the mobile
phone.
*-
Enable the mobile
phone’s Bluetooth®
connection.
*-
Stop the mobile
phone’s security
software and close
all applications.
*-
Before using an
application installed
on the mobile
phone, carefully
check its source
and how its opera-
tion might affect this
system.
*-
Updating the system