2022 TOYOTA GR86 jump start

211
4
4-5. EyeSight
Driving
WA R N I N G
• Fluid has not been fully wiped off
the windshield during or after use of
the window washer.
• Obstacles cannot be correctly rec-
ognized due to water droplets from rain or the washer, or the wiper
blades obstructing the stereo cam-
era’s field of view.
• The stereo camera’s field of view is
obstructed.
• With low obstacles (low wall, crash
barrier, low vehicle, etc.)
• The size and height of an obstacle
is smaller than the limitations of the
stereo camera’s recognition capa- bility. (Small animals, children,
pedestrians who are sitting or lying
down, etc.)
• The rear portion nearest your vehi-
cle is too small or too close (such as a trailer or oncoming vehicle).
The system may not recognize the
part of that vehicle which is closest to you.
• There is a fence or wall, etc., with a uniform pattern (striped pattern,
brick, etc.) or with no pattern in
front.
• There is a wall or door made of glass or a mirror in front.
• An obstacle (another vehicle, motorcycle, bicycle, pedestrian,
animal or child, etc.) cuts in from
the side or jumps out suddenly.
• Your vehicle is immediately behind
an obstacle after changing lanes.
• On sharp curves, steep uphill
grades or steep downhill grades
●The system determines that steer-
ing operation by the driver is intended as evasive action.
●For your safety, do not test Pre-Col-lision Throttle Management on its
own. It may operate improperly and
cause an accident.
NOTICE
In the following situations, turn off Pre-Collision Throttle Management.
Otherwise Pre-Collision Throttle Man-
agement may activate unexpectedly.
●The vehicle is being towed.
●The vehicle is being loaded onto a
carrier.
●A chassis dynamometer, free-roll-
ers or similar equipment is being
used.
●A mechanic lifts up the vehicle,
starts the engine and allows the wheels to spin freely.
●Driving on a race track

359
7
7-2. Steps to take in an emergency
When trouble arises
cal key when the alarm system is set,
the alarm may be triggered.
■Changing engine switch modes
Release the brake pedal (automatic
transmission) or clutch pedal (manual
transmission) and press the engine switch in step 3 above.
The engine does not start and modes
will be changed each time the switch is pressed. ( P.141)
If you have a set of jumper (or
booster) cables and a second vehi-
cle with a 12-volt battery, you can
jump start your vehicle by following
the steps below.
1 Vehicles with an alarm (P. 8 1 ) :
Confirm that the electronic key
is being carried.
When connecting the jumper (or
booster) cables, depending on the situ- ation, the alarm may activate and doors
locked.
2 Open the hood. (P.293)
3 Connect a positive jumper cable clamp to on your vehicle and con-
nect the clamp on the other end of the positive cable to on the sec-
ond vehicle. Then, connect a negativ e cable clamp to on the second
If the vehicle batter y is
discharged
The following procedures may
be used to start the engine if
the vehicle’s battery is dis-
charged.
You can also call any author-
ized Toyota retailer or Toyota
authorized repairer, or any reli-
able repairer.
Restarting the engine
A
B
C

3607-2. Steps to take in an emergency
vehicle and connect the clamp at the other end of the negative cable to
.
Positive (+) battery terminal (your vehicle)
Positive (+) battery terminal (second vehicle)
Negative (-) battery terminal (second vehicle)
Connect the jumper cable to ground on your vehicle as shown in the
illustration.
4 Start the engine of the second
vehicle. Increase the engine
speed slightly and maintain at
that level for approximately 5
minutes to recharge the battery
of your vehicle.
5 Open and close any of the door
of your vehicle with the engine
switch off.
6 Maintain the engine speed of
the second vehicle and start the
engine of your vehicle by turning
the engine switch to ON.
7 Once the vehicle’s engine has
started, remove the jumper
cables in the exact reverse
order from which they were con-
nected.
Once the engine starts, have the
vehicle inspected at any author-
ized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer as soon as possible.
■Starting the engine when the bat-
tery is discharged
The engine cannot be started by
push-starting.
■To prevent battery discharge
●Turn off the headlights and the audio
system while the engine is off.
●Turn off any unnecessary electrical
components when the vehicle is run-
ning at a low speed for an extended period, such as in heavy traffic.
D
A
C
D

361
7
7-2. Steps to take in an emergency
When trouble arises
■When the battery is removed or dis-
charged
Information stored in the ECU is
cleared. When the battery is depleted,
have the vehicle inspected at any authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer.
■When removing the battery termi- nals
When the battery terminals are
removed, the information stored in the ECU is cleared. Before removing the
battery terminals, contact any author-
ized Toyota retailer or Toyota authorized repairer, or any reliable repairer.
■Charging the battery
The electricity stored in the battery will
discharge gradually even when the vehi- cle is not in use, due to natural dis-
charge and the draining effects of
certain electrical appliances. If the vehi- cle is left for a long time, the battery may
discharge, and the engine may be una-
ble to start. (The battery recharges auto- matically during driving.)
■When recharging or replacing the
battery
●In some cases, it may not be possible
to unlock the doors using the smart
entry & start system when the battery is discharged. Use the wireless
remote control or the mechanical key
to lock or unlock the doors.
●The engine may not start on the first
attempt after the battery has recharged but will start normally after
the second attempt. This is not a mal-
function.
●The engine switch mode is memo-
rized by the vehicle. When the battery
is reconnected, the system will return to the mode it was in before the bat-
tery was discharged. Before discon-
necting the battery, turn the engine switch off.
If you are unsure what mode the
engine switch was in before the bat- tery discharged, be especially careful
when reconnecting the battery.
WA R N I N G
■When removing the battery ter- minals
Always remove the negative (-) termi-
nal first. If the positive (+) terminal contacts any metal in the surrounding
area when the positive (+) terminal is
removed, a spark may occur, leading
to a fire in addition to electrical shocks and death or serious injury.
■Avoiding battery fires or explo-sions
Observe the following precautions to
prevent accidentally igniting the flam- mable gas that may be emitted from
the battery:
●Make sure each jumper cable is
connected to the correct terminal
and that it is not unintentionally in contact with any other than the
intended terminal.
●Do not allow the + and - clamps of
the jumper cables to come into con-
tact with each other.
●Do not smoke, use matches, ciga-
rette lighters or allow open flame near the battery.
■Battery precautions
The battery contains poisonous and
corrosive acidic electrolyte, while
related parts contain lead and lead compounds. Observe the following
precautions when handling the bat-
tery:
●When working with the battery,
always wear safety glasses and take care not to allow any battery
fluids (acid) to come into contact
with skin, clothing or the vehicle body.
●Do not lean over the battery.

3627-2. Steps to take in an emergency
1Stop the vehicle in a safe place
and turn off the air conditioning
system, and then stop the
engine.
2 If you see steam: Carefully lift
the hood after the steam sub-
sides.
If you do not see steam: Care-
fully lift the hood.
3 After the engine has cooled
down sufficiently, inspect the
WA R N I N G
●In the event that battery fluid comes
into contact with the skin or eyes,
immediately wash the affected area with water and seek medical atten-
tion. Place a wet sponge or cloth
over the affected area until medical attention can be received.
●Always wash your hands after han-
dling the battery support, terminals, and other battery-related parts.
●Do not allow children near the bat-tery.
■To prevent damage to the vehicle
Do not pull- or push-start the vehicle
as the three-way catalytic converter
may overheat and become a fire haz- ard.
NOTICE
■When handling jumper cables
Be careful that the jumper cables do
not become tangled in the cooling fans or any of the belts when connect-
ing or disconnecting them.
■When closing the doors
While pushing the door glass towards
the inside of the vehicle, slowly close the door.
Because the side window open/close
function linked to door operation will not operate, the window may interfere
with the vehicle body, possibly
scratching both the vehicle body and window, or even shattering the win-
dow.
If your vehicle overheats
The following may indicate that
your vehicle is overheating.
 The engine coolant tempera-
ture gauge ( P.88) is in the
red zone or a loss of engine
power is experienced. (For
example, the vehicle speed
does not increase.)
 “High Coolant Temperature
Check Owner's Manual” is
shown on the multi-information
display.
 Steam comes out from under
the hood.
Correction procedures

182-1. Basic information before operation
changed, depending on the language,
in rare cases te xt may not be dis- played correctly.
The list screen can be scrolled by a
swipe gesture.
For details on the operation: P. 1 5
Select to skip to the next or pre-
vious page.
This indicates the displayed
screen’s position.
Faster scrolling is possible by
dragging the position indicator.
Some lists contain character
screen buttons which allow
users to jump directly to list
entries that begin with the same
letter as the character screen
button.
Every time the same character
screen button is selected, the
list starting with the subsequent
character is displayed.
The brightness of the screen can
be adjusted.
Refer to the “OWNER'S MANUAL”
for details.
List screen
A
B
C
Screen adjustment
Adjusting brightness