2021 MERCEDES-BENZ V-CLASS MPV light

#
Obser vethe no tes on loading (/ page212). #
Push there ar seats back fully or, if necessar y,
re mo vethem. #
Lift off bo thcovers 1 from the guide rail
using a suitable tool, e.g. a scr ewdriver. #
Press bo thcovers 1 toge ther slightly and
re mo vethem from the guide rail.
The openings in thera ilfo rth e middle slide
on the underside of thefo lding table will be
open. #
Rotate thefo lding table until the ar row onthe
unde rside of thefo lding table is pointing in
th e direction of tr avel. Ins
tallation position #
Insert thefo lding table into guide rails 2 so
th at ar rows3 onthefo lding table point to
bo th markings 4on guide rail2.
The guides and sliding rail on the underside of
th efo lding tablefit into the guide rail. #
Pull le ver5 onthe front or rear side of the
fo lding table upwards and push thefo lding
ta ble backwards.
Press bo thcovers 1 toget her slightly and
engage them in the openings of the guide rails.
Moving thefo lding table #
Keep le ver5 pulled and mo vethefo lding
ta ble into the desired position. #
Release le ver5. #
Movethefo lding table until it automatically
engages in the next possible position. #
Afterre positioning theta ble, ensure that the
fo lding table is proper lysecured again.
Re moving the folding table #
Fold in theta ble panels and retract theta ble. #
Push there ar seats back fully or, if necessar y,
re mo vethem. #
Push thefo lding table back far enough so that
co vers 1 ofthe openings in thera il can be
re mo ved. #
Lift off bo thcovers 1 from the guide rail
using a suitable tool, e.g. a scr ewdriver. #
Press bo thcovers 1 toge ther slightly and
re mo vethem from guide rail2.
The openings in thera ilfo rth e middle slide
on the underside of thefo lding table will be
open. #
Push thefo lding tableforw ards into the
ins tallation position.
Ar row s3 onthefo lding table point toboth
markings 4on guide rail2. #
Lift thefo lding table out of guide rail2. Seats and
stowage 99

#
Press bo thcovers 1 toge ther slightly and
engage them in the openings of guide rails
2. Using
thefo lding table Extending
thefo lding table #
Press button 1allthewa y down and release
it.
The folding table will mo veupwards and
engage automaticall y.
Re tracting the folding table #
Press button 1allthewa y down and simul‐
ta neously press the cent resection of thefo ld‐
ing table down wards. #
Release button 1when thefo lding table is in
its retracted position.
The centre section of thefo lding table will
engage automaticall y.
Fo lding the table panel in and out #
Tofold out the table panel: pull outthe
ta ble panels upwards tothestop using handle
2 and swing them tothe side until they
engage. #
Tofold in the table panel: swingtheta ble
panels up using handle 3and slide them
ve rtically down wards into theta ble.
Installing and removing the inse rt 4
Recesses on thefo lding table
5 Stow age compartments #
Toremo ve: press lug 6and remo vethe
insert. #
Toinstall: put inthe insert and press it down
until it engages. Information about
the bottle holder
The bottle holders are in front of thestow age
compartments in the front doors.
There are additional bottle holders on the left and
ri ght in there ar compartment side trim. 100
Seats and stowage

Cup holders
Inserting
the cup holder in there ar passen ger
compa rtment #
Position cup holder 1abo vestow age com‐
partment 3sothat "INSIDE" lettering on its
base 2faces towa rdsth eve hicle interior. #
Insert base 2into stow age compartment 3
and press down on bo thsides.
The cup holder is cor rectly inse rted when bo th
sealing rings 5are inse rted in stowage com‐
partment 3and upper edge 4ofthe base
loc kspositively with stowage compartment 3. #
Toremo ve: grasp the bottom of cup holder
1 from below and remo veitby lifting its
base 2out verticall y. Switching
thetemp erature-cont rolled cup
holders on and off Re
quirements:
R The ignition is switched on. #
Toswitch on: pressthe button 1repeatedly
until the blue (keep cool) or red (keep warm)
indicator lamp in the button lights up. #
Toswitch off: pressthe button 1repeat‐
edly until the indicator lamp in the button
goes out.
% Clean
there mo vable rubber mat only with
clean, luk ewarmwate r and the cup holder 2
only with a damp clo th. Asht
ray and cigar ette lighter Using asht
rays #
Slide co ver1 ofthe cent reconsole up wards
( / page 96). #
Insert the ashtr aywith cap 2into a cup
holder in the cent reconsole wi thcover or
into a cup holder in there ar passenger com‐
partment. Using ashtr
ays #
Slide co ver1 ofthe cent reconsole up wards
( / page 96). #
Insert the ashtr aywith cap 2into a cup
holder in the cent reconsole wi thcover or
into a cup holder in there ar passenger com‐
partment. Seats and
stowage 101

Using
the ashtr ayand cigar ette lighter in the
re ar passen ger co mpartment Re
quirements
R The ignition is switched on. #
Pull down the co ver. #
Touse the cigar ette lighter: press cigar ette
lighter 2.
The cigar ette lighter will pop out when the
heating element is red-hot. #
Toremo vethe ashtr ay:press ribbing 1
and remo veinsert 3. #
Toinsert the ashtr ay:push in insert 3
from ab oveand press it into the holder until it
engages. Using
the cigar ette lighter in the front centre
console &
WARNING ‑ Risk of fire and injury from
th e hot cigar ette lighter
Yo u can burn yourself if youto uch the hot
heating element or the soc ket of the cigar ette
lighter.
In addition, flammable materials may ignite if:
R you drop the hot cigar ette lighter
R ach ild holds the hot cigar ette lighter to
objects, forex ample #
Always hold the cigar ette lighter bythe
knob. #
Always make sure that the cigar ette
lighter is out of reach of children. #
Never lea vechildren unat tended in the
ve hicle. Re
quirements:
R The po wer supp lyhas been switched on. Cigar
ette lighter in the cent reconsole (e xamp le:
centre console with co ver) #
Slide co ver1 ofthe cent reconsole up wards
( / page 96). #
Press in cigar ette lighter 2.
% Yo
u can use the cigar ette lighter soc ketfor
accesso ries with a maximum cur rent dr awof
18 0 W (15 A). Soc
kets Using the
12V so cket inthe front centre con‐
sole Re
quirements:
R The po wer supp lyhas been switched on.
R Only devices with up toa maximum of
18 0wa tts (15 A) are pe rmissible. #
Slide co ver1 ofthe cent reconsole up wards
( / page 96). #
Fold up co ver2 ofthe soc ket. #
Inse rtthe plug of the device. 102
Seats and stowage

#
Insert the plug of the device into 230 V
soc ket3.
When the on-board electrical sy stem voltage
is suf ficient, indicator la mp1lights up.
When you are not using the 230 V po wer soc ket,
ke ep theflap closed. Swit
ching there frigerator box in the centre
console on and off &
WARNING Risk offire due toa co vered
ve ntilation grille on the coolbox
If yo u co verth eve ntilation grille forth e cool‐
box, it may overheat. #
Always make sure that theve ntilation
grille is not co vered. The coolbox
ventilation grille is between the front
seat base and the cent reconsole sid ewall.
Re quirements
R The ignition is switched on.
R The stow age compartment under the armrest
is open (/ page 96). The
refrigerator box can bear a maximum load of
3.5 kg. #
Toopen: fold co ver1 upwards. #
Toswitch the cooling le velto low: press
button 2for appro ximately two seconds. #
Toswitch the cooling le velto high: press
button 2again. #
Toswitch off: press button 2for appro x‐
ima tely two seconds until all indica tor lamps
go out. %
If
yo u do not need touse there frigerator box
fo r an extended pe riod, you should swit chit
off, defrost it and clean it. Af ter doing so,
lea vethe cap open for a time. Note
s on attaching the iPad ® Yo
ur vehicle is equipped with iPad ®
attachment
1 onthe driver's and co-driver's seat backrests.
A mount, which has been tested and appr oved
especially for Mercedes-Benz vehicles, is availa‐
ble as an accesso ry. Only this mount can unlock
th e attachment opening and allow the iPad ®
to
be charge d whilst it is ins talled.
iPad ®
attachment 1may only be used for
accesso ries up to42 W (3.5 A).
Contact a Mercedes-Benz Service Centre for
information and availabilit y.Before using the
mount, please read the operating instructions for
th e mount.
% Only use accessories which ha
vebeen tested
and recommended byMercedes-Benz. 104
Seats and stowage

Exterior lighting
Note
s onchanging the lights when driving
abroad Low beam
In countries in which traf
fic drives on the oppo‐
site side of thero ad from the count ryin which
th eve hicle is regis tere d, you will ha vetoswitch
th e headlamps tosymmetrical dipped beam. This
will pr event oncoming traf fic from being dazzled.
Symm etrical dipped beam will no longer illumi‐
nate the edge of the car riag ew ay as far or as
high.
Ve hicles with halogen headlamps:
It is not necessa ryto change the headlamps over
to symmetrical dipped beam. The statutory
re qu irements of the count ries in which traf fic
drives on the opposite side of thero ad from the
country in whi chtheve hicle is regis tere d will also
be met without changing over.
Ve hicles with LED headlamps:
Yo u can set the low beam for driving on theright
or left via the on-board computer (/ page189). Infor
mation about lighting sy stems and your
re sponsibility The
vehicle's various lighting sy stems are only
aids. The vehicle driver is responsible for adjust‐
ing theve hicle's lighting tothe pr evailing light,
visibilit y,statutory conditions and traf fic condi‐
tions. Light switch
Operating the light switch
0047
0063 Left pa rking lights
0048 0064 Right parking lights
0049 0060 Standing lights and licence plate and
instrument lighting
004A 0058 Automatic driving lights (prefer red light
switch position)
004B 0058 Low beam or high beam
6 005E Rear fog light
7 005A Front fog lamp
If yo u hear a warning tone when exiting theve hi‐
cle, the lights may still be on. #
Turn the light switch to0058 .
The exterior lighting (e xcept standing and parking
lights) will automatically swit choff in thefo llow‐
ing cases:
R ifyo ure mo vetheke y from the ignition loc k.
R ifyo u open the driver's door while theke y is
in position 005Ainthe ignition loc k.
Switching on the daytime running lights #
Turn the light switch to0058 .
Au tomatic driving lights function
The standing lights, low beam and daytime run‐
ning lights will be switched on auto matically
depending on the ignition status and the light
conditions. Light and vision
105

&
WARNING Risk of accident when the
dipped beam is switched off in poor visi‐
bility
When the light switch is set to0058 ,the
dipped beam may not be switched on auto‐
matically if there is fog, snow or other causes
of poor visibility such as spr ay.#
In such cases, turn the light switch to
0058 . The automatic driving lights are only an aid.
Re
sponsibility forve hicle lighting rests with you.
If th est anding lights and low beam ha vebeen
switched on, the green 0060(sta nding lights) and
0058 (low beam) indicator lamps on the instru‐
ment clus ter will light up.
Ac tivating/deactivating the fog light
Re quirements:
R The light switch is in the0058 or0058 posi‐
tion.
R The po wer supply has been switched on. #
Toswitch there ar fog light on or off: press
th e button 005E.
Comply with the count ry-specific regulations for
using there ar fog lamp.
Ad justing headlamp range #
Turn headlamp range adjus ter1 tothe
re qu ired position. #
Ifth eve hicle is unladen, select position 005A.
The illumination of thero ad should be 40 m to
10 0 m and low beam must not dazzle oncoming
traf fic. Yo
u can use the headlamp range adjus terto
adjust the light cone of the headlamps to your
ve hicle's load condition. The light cone will
ch ange as the seats are occupied or the load
compartment is loaded or unloaded. This can
cause visibility conditions todeteriorate and you
could dazzle oncoming traf fic. Operating the combination light switch
1
High beam
2 Right turn signal light
3 Headla mpflashing
4 Left turn signal light #
Use the combination switch toactivate the
desired function.
Switching on high beam #
Switch on the low beam (/ page105). #
Push the combination switch forw ards 1.
The 0057 indicator lamp on the instrument
clus ter will light up.
% The high beam switches tothe0058 position
only in darkness and when the engine is run‐
ning. #
Toswitch off: movethe combination switch
back toits starting position.
The 0057 indicator lamp on the instrument
clus ter will light up.
Headlamp flashing #
Brief lypull the combination switch in the
direction of ar row3.
Tu rn signal lights #
Toindicate: pushthe combination switch in
th ere qu ired direction 2or4 until it 106
Light and vision

engages. In
the case of larger steering mo ve‐
ments, the combination switch will automati‐
cally switch bac k. #
Toindicate briefl y:tapth e combination
switch briefly in there qu ired direction 2or
4. The cor responding turn signal lamp will
fl ash thre e times. Switching
the hazard warning light sy stem
on/off #
Press button 1.
If yo u operate a turn signal indicator while the
hazard warning light sy stem is switched on, only
th e turn signal lamps on there leva nt side of the
ve hicle will light up.
The hazard warning light sy stem will switch on
automatically in thefo llowing situations:
R The airbag is deplo yed
R The vehicle is heavily braked from a speed of
more than 70 km/h toast andstill.
The hazard warning light sy stem will automati‐
cally switch off when theve hicle rega ins a speed
of more than 10 km/h af ter maximum full-s top
braking.
% The hazard
warning light sy stem will work
eve n when theve hicle has been switched off. Intelligent Light Sy
stem Fu
nction of the Intelligent Light Sy stem
The In telligent Light Sy stem adapts the head‐
lamps' lighting function tothe cur rent driving and
we ather situation. The sy
stem comprises thefo llowing functions:
R Active light function (/ page 107)
R Cornering light (/ page107)
R Motorw ay mode (/ page108)
R Enhanced fog light function (/ page108)
Yo u can swit ch the Intelligent Light Sy stem func‐
tion on or off via the on-board computer
(/ page 108).
Ac tive light function The acti
velight function has thefo llowing func‐
tions:
R The headlamps follow thesteering mo ve‐
ments.
R Releva nt areas are better illumina ted during a
journe y.
The functions will be active when low beam is
switched on.
The active light function can, forex ample, de tect
pedestrians, cyclist s and animals at an earlier
st age.
Cornering light function The function is active under
thefo llowing condi‐
tions:
R Your speed is less than 40 km/h and the turn
signal light has been switched on or the
st eering wheel is turned.
R Your speed is between 40 km/h and
70 km/h and thesteering wheel is turned. Light and vision
107