2021 MERCEDES-BENZ V-CLASS MPV light

The cornering light may
still light up for a short
time but will be switched off automatically af ter a
maximum of thre e minutes.
Mo torw ay mode function
Mo torw ay mode increases thera nge and bright‐
ness of the cone of light, enabling better visibility. Mo
torw ay mode will automatically be activated in
th efo llowing cases:
R Your speed is greaterth an 110 km/h and the
ve hicle has co vered at least 1,000 m without
any signi ficant steering mo vement.
R Your speed is greater than 130 km/h.
If yo ur speed falls below 80 km/h af ter mo torw ay
mode has been activated, it will automatically be
deactivated.
Enhanced fog light function
The enhanced fog light function reduces self-daz‐
zling and impr ovesth e illumination of the edge of
th e car riag ewa y. If
yo ur speed is below 70 km/h and thefo g light
has been switched on, the enhanced fog light
function will automatically be activated.
The enhanced fog light function will automatically
be deactivated af ter activation in thefo llowing
cases:
R Your speed is greaterth an 100 km/h.
R The fog light is switched off. Switching
the Intelligent Light Sy stem on/off #
Press the00E2 button tocall up the list of
menus. #
Use the0064 or0063 button toselect Set-
tings. #
Press the0076 button. #
Use the0064 or0063 button toselect
Lights. #
Press the0076 button. #
Use the0064 or0063 button toselect Intelli-
gent Light System.
If th e Intelligent Light Sy stem has been
switched on, the display will show the0058
symbol in yellow on the instrument clus ter. #
Press the0076 button.
When you swit chon the Intelligent Light Sy stem
function, you will enable thefo llowing functions:
R Motorw ay mode
R Active light function
R Cornering light
R Enhanced fog light function
% If
yo u set the low beam for driving on the
ri ght or left, the display will show the display
message Inactive for left-side traffic orInac-
tive for right-side traffic intheLights sub‐
menu ins tead of Intelligent Light System
(/ page 189). This display messa gewill
appear only if the setting for driving on the
ri ght or left is the opposite to yourvehicle's
national version.
% Yo
u can find fur ther information in "Intelli‐
ge nt Light Sy stem" (/ page107). Ad
aptive Highbeam Assist Ad
aptive Highbeam Assist function &
WARNING Risk of accident despite
Ad aptive Highbeam Assist
Ad aptive Highbeam Assist does not react to:
R road users without lights, e.g. pedestrians
R road users with poor lighting, e.g. cyclists
R road users whose lighting is obstructed,
e.g. bya bar rier
On very rare occasions, Adaptive Highbeam
Assist may failto recognise other road users
with their own lighting, or may recognise
th em too late. 108
Light and vision

In
these, or in similar situations, the auto‐
matic high beam will not be deactivated or
will be activated despite the presence of
ot her road users. #
Always obser vethero ad and traf fic con‐
ditions carefully and switch off the high
beam in good time. The
Adaptive Highbeam Assist automatically
swit ches between thefo llowing settings:
R Low beam
R High beam
The sy stem de tects that vehicle lights are
approaching in the opposite direction or driving
ahead of theve hicle.
If yo ur speed is greater than 30 km/h and no
ot her road users are de tected, high beam will
au tomatically be switched on.
If yo ur speed is greater than 25 km/h, the head‐
lamp range will be controlled au tomatical ly
depending on the dis tance from other road users.
High beam will automatically be deactivated in
th efo llowing cases:
R Your speed is lo werth an 25 km/h.
R Other road users ha vebeen de tected.
R The road is suf ficiently illumina ted.
Sy stem limits
Ad aptive Highbeam Assist cannot take thero ad,
we ather or traf fic conditions into consideration.
The de tection of obs tacles may be restricted if:
R visibility is poo r,e.g. in fog, heavy rain or
sno w.
R the sensors are dirty or co vered. Ad
aptive Highbeam Assist is only an aid. You are
re sponsible for ensuring cor rect vehicle lighting
in accordance with the pr evailing light, visibility
and traf fic conditions.
The sy stem's optical sensor is located behind the
windscreen near theove rhead cont rol panel.
Switching Highbeam Assist on/off
Requ irements
R The light switch is in the0058 position. #
Toswitch on: switch on high beam using the
combination switch.
If high beam is au tomatical lyswitched on in
darkness, the00CE indicator lamp on the
multifunction display will light up. #
Toswitch off: switch off high beam using the
combination switch. Ad
aptive Highbeam Assist Plus Ad
aptive Highbeam Assist Plus function &
WARNING Risk of accident despite
Ad aptive Highbeam Assist Plus
Ad aptive Highbeam Assist Plus does not react
to:
R road users without lights, e.g. pedestrians
R road users with poor lighting, e.g. cyclists
R road users whose lighting is obstructed,
e.g. bya bar rier
On very rare occasions, Adaptive Highbeam
Assist Plus may failto recognise other road
users with their own lighting, or may recog‐
nise them too late.
In these, or in similar situations, the auto‐
matic high beam will not be deactivated or
will be activated despite the presence of
ot her road users. #
Always obser vethero ad and traf fic con‐
ditions carefully and switch off the high
beam in good time. Ad
aptive Highbeam Assist Plus cannot take into
account road, weather or traf fic conditions.
De tection may be restricted in thefo llowing
cases:
R In poor visibilit y,e.g. fog, heavy rain or snow
R ifth ere is dirt on the sensors or the sensors
are obscured Light and vision
109

Ad
aptive Highbeam Assist Plus is only an aid. Yo u
are responsible for ensuring cor rect vehicle light‐
ing in accordance with the pr evailing light, visibil‐
ity and traf fic conditions. Ad
aptive Highbeam Assist Plus swit ches auto‐
matically between thefo llowing light types:
R Low beam
R Partial high beam
R High beam
Pa rtial high beam uses high beam toshine past
ot her road users rath er than dazzling them. The
low beam illumination area co vers theve hicle in
front.
At speeds lo werth an 25 km/h or if there is insuf‐
fi cient stre et lighting, Highbeam Assist Plus will
per form thefo llowing actions:
R Partial high beam and high beam will be auto‐
matically deactivated.
R The 0057 indicator lamp on the instrument
clus ter will go out. The 00CEsymbol for High‐
beam Assist Plus will remain switched on.
At speeds greater than 30 km/h, Highbeam
Assist Plus will per form thefo llowing actions:
R If no other road users are de tected, high
beam will be switched on.
R Ifot her road users are de tected, part ial high
beam will be switched on.
R The 0057 indicator lamp on the instrument
clus ter will light up. At
speeds greater than 40 km/h, Highbeam
Assist Plus will per form thefo llowing actions:
R If no other road users are de tected and the
ro ad is stra ight, high beam will be switched
on.
R If highly reflective signs are de tected, high
beam will auto maticallybe switched off.
R Ifot her road users are de tected, part ial high
beam will be switched on automaticall y.
R The 0057 indicator lamp on the instrument
clus ter will light up.
The sy stem's optical sensor is located behind the
windscreen near theove rhead cont rol panel.
Switching Adaptive Highbeam Assist Plus
on/off
Requ irements
R The light switch is in the0058 position. #
Toswitch on: switch on high beam using the
combination switch.
If high beam is au tomatical lyswitched on in
darkness, the00CE indicator lamp on the
multifunction display will light up. #
Toswitch off: switch off high beam using the
combination switch. Setting the
exterior lighting switch-off delay
time Re
quirements:
R The light switch is in the0058 position.
Multimedia sy stem:
4 © 5
Settings 5
Lights
5 Ext. light. del. sw. off #
Set a switch-off delay time.
When theve hicle engine is switched off, theex te‐
ri or lighting will be activated forth e set time. Ac
tivating and deactivating the sur round
lighting Multimedia sy
stem:
4 © 5
Settings 5
Lights
5 Surround lighting #
Activate or deacti vate the function.
The exterior lighting will remain on for 40 sec‐
onds af terth eve hicle is unloc ked. When you
st art theve hicle, the sur round lighting will be 11 0
Light and vision

deactivated and
the automatic driving lights acti‐
va ted. Ad
justing the in terior lighting Ad
justing the in terior lighting Fr
ont overhead control panel In
te rior lighting buttons (e xample: com fort ove r‐
head control panel)
1003D Front-left reading lamp
20033 Automatic interior lighting control
3004A Front interior lighting
40044 Rear or load compartment lighting
5003D Front-ri ghtreading lamp #
Toswitch on/off: pressthe cor responding
button 1–5.
The la yout and number of buttons depend on the
equipment.
Operating unit in thegr ab handle 1003D
Rear reading lamp #
Toswitch on/off: press button1. Ad
justing ambient lighting Multimedia sy
stem:
4 © 5
Comfort 5
Ambient lighting
Setting the colour #
Select Colour. #
Set therequ ired colour.
Ad justing the brightness #
Select Brightness . #
Adjust the brightness. #
Select a colour combination. Switching
the interior lighting switch-off
delay time on/off Multimedia sy
stem:
4 © 5
Settings 5
Lights
5 Int. light. del. sw. off #
Switch the switch-off delay time on or off.
When this function is active, the interior light‐
ing switches on automatically when the
engine is unloc ked or switched off. Changing bulbs
Instructions
forre placing light sou rces &
WARNING Risk of burn s from hot com‐
ponent parts whilst replacing a bulb
Bulbs, lamps and plug connectors can
become very hot during operation.
When replacing a bulb, you could burn your‐
self on these component parts. #
Allow the component parts tocool
down before replacing the bulbs. Impor
tant sa fety no tes
R Before changing the bulbs, switch off the
ve hicle's lighting sy stem. This will pr event a
sho rtcircuit.
R Use only spa rebulbs of the same type and
with the cor rect voltage.
R Use bulbs only in enclosed lamps that ha ve
been designed forth em.
R Do not use any light source that has been
dropped or has scratches on its glass tube.
Otherwise, the light source may explode.
R The light source may explode under thefo l‐
lowing conditions:
- if it is hot and youto uch it
- ifyo u drop it
- ifyo u sc ratch it
R Stains on theglass tube will reduce the
service life of the light source. Do not touch
th eglass tube with your bare hands. If neces‐ Light and vision
111

sar
y,clean theglass tube with alcohol or spi‐
ri ts while it is cold and wipe it down wi th a
lint-f ree clo th.
R Protect light sources from moisture and do
not bring them into contact with liquids.
Alw ays ensure the bulbs are firm ly secu red.
Ha ve thefo llowing light sources changed at a
qu alified specialist workshop only:
R Additional turn signal lamps on the outside
mir ror
R Bulbs in the licence plate lighting Re
placing front light bulbs (vehicles with hal‐
ogen headlamps) Overview of front light sourc
e types1
Additional turn signal lamp on the outside
mir ror: LED
2 Turn signal light: PY 21 W
3 Low beam: H7 55 W
4 High beam/s tanding/parking lights/daytime
ru nning lights: H15 55 W/15 W
Re placing light sou rces in the headlamp
Re quirements
R The lighting sy stem is switched off.
R The appropriate front wheel is turned
inwa rds.
R Low beam: youre qu ire a H7 55 W light bulb.
R Turn signal light: yourequ ire a PY 21W light
bulb.
R High beam /
standing/parking lights /
daytime running lights: youre qu ire a
H15 55 W/15 W light bulb. Fi
tting/ removing the co ver in the front wheel
ar ch #
Toremo ve:grip the cent reof co ver1, slide
it upwards and pull it out.
The co ver will hang down wards on thest ra p. #
Tofit: insert co ver1 attheto p and slide it
down wards until it engages.
Low beam #
Remo vethe co ver in the front wheel ar ch. #
Turn housing co ver1 anti-clockwise and
re mo veit. #
Turn soc ket2 for low beam tothe left and
pull it out. #
Pull the bulb out of soc ket2. #
Inse rtthe new bulb into soc ket2. #
Inse rtsoc ket2 and rotate itto theright to
tighten it. #
Press on housing co ver1 and rotate itto
th eright totighten it. 11 2
Light and vision

#
Replace the co ver in the front wheel ar ch.
High beam, standing/parking lights and day‐
time running lights #
Open the bonn et. #
Turn housing co ver1 anti-clockwise and
re mo veit. #
Pull out the bulb with soc ket2. #
Inse rtthe new bulb with soc ket2 and
engage it as far as it will go. #
Press on housing co ver1 and rotate itto
th eright totighten it. #
Close the bonn et.
Tu rn signal light #
Open the bonn et. #
Turn soc ket1 anti-clo ckwise and pull it out. #
Pull the bulb out of soc ket1. #
Inse rtthe new bulb into soc ket1. #
Inse rtsoc ket1 and turn it clo ckwise until it
engages. #
Close the bonn et. Re
placing rear bulbs Overview of
rear light source types Ve
hicles with standard tail lamp
1 Third brake light: LED
2 Licence plate lighting: LED
3 Rear fog light (driver's side): P 21 W
4 Reversing light: P 21 W
5 Brake light, tail light/parking lights: P 21 W
6 Turn signal light: P 21 W
Ve hicles with LED tail lamps
1 Third brake light: LED
2 Licence plate lighting: LED
3 Rear fog light (driver's side): LED
4 Reversing light: W 16 W
5 Brake light, tail light/parking lights: LED
6 Turn signal light: LED
Re placing light sou rces in the tail lamp
Re quirements
R The lighting sy stem is switched off.
R Standard tail lamp: yourequ ire a P 21 W
light source.
R LED tail lamp: yourequ ire a W 16W light
source.
Re moving the tail lamp
* NO
TEDama getothe paintwork during
ta il lamp remo val The paintwork may be damaged when
theta il
lamps are remo ved. The tail lamp ma y,for
ex ample, scratch the paintwork when it is
re mo ved. #
Remo vetheta il lamps carefull y. #
Mercedes-Benz recommends having the
ta il lamp light sources replaced at a
qu alified specialist workshop. Light and vision
11 3

Please no
tethat you can change the bulb of the
re ve rsing light only in the case of an LED tail
lamp. #
Open theta ilgate.
% Yo
u will find a scr ewdriver in theve hicle tool
kit (/ page247). #
Unscr ewtwo side scre ws1. #
Push tail lamp 2outwards against bolts 3
as far as it will go. #
Press tail lamp 2off outwards and away
from bolts 3. #
Pull the connector off the bulb mount of tail
lamp 2.
Installing the tail lamp #
Push the connector into the bulb mount of tail
lamp 2. #
Push tail lamp 2onto bolts 3from the side
and press it against theve hicle. #
Tighten two side scr ews1.
St andard tail lamp #
Unscr ewthre e scr ews1 and remo vebulb
mount 2from theta il lamp. Bulb mount
3
Turn signal light
4 Brake light, tail light, parking light
5 Reversing light
6 Rear fog light (only on the driver's side) #
Remo vetheta il lamp. #
Gently turn the bulb anti-clockwise and take it
out of the soc ket. #
Push the new bulb into the soc ket and turn it
clo ckwise toscr ew it in. #
Insert bulb mount 2into theta il lamp and
tigh ten all thre e scr ews1. #
Installth eta il lamp.
LED tail lamp #
Remo vetheta il lamp. #
Unscr ewhousing co ver1 byturning it anti-
clo ckwise. #
Turn the soc ket anti-clo ckwise and pull it out. #
Pull the bulb out of the soc ket. #
Inse rtthe new bulb into the soc ket. #
Inse rtthe soc ket and rotate it clockwise to
tighten it. #
Press on housing co ver1 and rotate it
clockwise totighten it. #
Installth eta il lamp. 11 4
Light and vision

Re
placing interior light bulbs Re
placing light sou rces in the interior
Re quirements
R The interior lighting has been switched off.
R Rear and load comp artment lamp:you
requ ire a T10 6W xenon light sou rce.
R Interior and sur round lighting: yourequ ire
a W 5 W light source.
R Signal and ambient lamp in
the tailgate:
yo ure qu ire a W 5 W light source.
Re ar and load comp artment lamps #
Push in the catch spring of lens 1with a
suitable object, e.g. a scr ewdriver, and then
prise off the lens with the lamp housing. #
Push the lugs of soc ket2 inwa rds. #
Remo velight source 3from the lamp hous‐
ing. #
Insert the new light source. #
Position the lens on the lamp housing and
engage it. #
Align the lens with the lamp housing and
engage it.
Ad ditional interior and sur round lighting
Depending on the equipment, replacing the light
sources as described here applies tothefo llow‐
ing lamps:
R The sun visor mir ror lamp
R The ambient lamp at the bottom of the front
door
R The ambient lamp on the inside of theta ilgate #
Push in the catch spring of lamp housing 1
with a suitable object, e.g. a scr ewdriver, and
prise off lamp housing 1. #
Turn soc ket2 anti-clo ckwise and pull it out
of lamp housing 1. #
Pull bulb 3out of soc ket2. #
Push new bulb 3into soc ket2. #
Screw soc ket2 into la mphousing 1by
turning it clo ckwise. #
Place lamp housing 1in position on the left
and engage it.
Signal and ambient lamp in the tailgate #
Push in the catch spring of the lamp housing
on the side of transparent lens 3with a suit‐
able object, e.g. a scr ewdriver, and prise off
th e lamp housing. #
Turn soc ket2 anti-clo ckwise and pull it out
of the lamp housing. #
Pull the bulb out of soc ket2. #
Push the new bulb into soc ket2. Light and vision
11 5