2021 MERCEDES-BENZ A-CLASS HATCHBACK Owners Manual

R
Has been inspec tedby aqu ali/ed elect ri-
cian #
For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer forch arg-
ing the high-voltage battery in an electric
ve hicle. #
Never use damaged charging cables. #
Do not extend thech arging cable. #
Do not use adap ters. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth ewa llbox. If
ch arging at a wallbox without pre-ins talled
cable, use the optionally available charging cable
fo rwa llbox and charging station (mode 3). The
ch arging cable is st owed in a bag in the boot/
luggage compartment.
Only use charging cables that ha vebeen tested
and appro vedby the manufacturer forch arging
th e high-voltage battery in an electric vehicle. &
D DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The amount of ene rgy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when
ch arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. 198
198
Driving and parking

N
N
o
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
olt ag
age batt
e batt er
ery at a
y at a
f
f as
ast c t c har
har ging st
ging st ation (mode 4)
ation (mode 4) &
D
D AN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable. R
Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The charging cable forth eve hicle must not be
lon gerth an 30 m due tothe legal requ irements in
some countries. This is toprev ent the inter fer-
ence of signals being received byradio communi-
cation devices in theve hicle or in close pr oximity
to thech arging station. Be awarethat parts of the
ch arging cable may be routed under ground. If in
doubt, ask thech arging station operator if this is
th e case before charging the high-voltage batter y.
The amount of energy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when ch
arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. Se
Se
tting t
tting t he maximum per
he maximum per missible c
missible char
harging cur-
ging cur-
r
r ent f
ent f or c
or char
harging at a mains soc ket
ging at a mains soc ket *
N
NO
OTE
TE Overloading the mains soc ket due
to excessive charging cur rent If
th ech arging cur rent is too high, the fuse
could be tripped or theex tern al mains supply
could overheat. #
Make sure that theex tern al mains supply
has been designed tohandle the set
ch arging cur rent. #
If necessar y,reduce the set charging
cur rent or use a di.erent mains soc ket. #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable.
Mercedes-Benz thoroughly tests these
original charging cables forth eir suitabil- Driving and parking
199
199

ity
for high-voltage charging of your vehi-
cle. Pur chase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere. #
Check the setting of the maximum
ch arge cur rent using thech arging capa-
city shown in the Instrument Displa y.Before
charging at a mains soc ket, ha vethe maxi-
mum permissible charging cur rent forth ere leva nt
mains soc ket or the building inspected byaqu ali-
/ed elect rician. The charging cable supplied is set
to a countr y-speci/c maximum charging cur rent
va lue. When charging abroad, the maximum value
may exceed the permitted value forth at countr y.
When abroad, obser vethe count ry-speci/c la ws
when charging. If you ha vequestions concerning
setting thech arging cur rent or if there is a mal-
function, please contact a quali/ed specialist
wo rkshop. #
Set the maximum permissible charging cur-
re nt in the multimedia system menu
(/ page 298). If
th eex act value of the maximum permissible
ch arging cur rent cannot be set, select the next
smaller adjustable value.
% Ifth eve hicle requ ires more time than usual to
ch arge the high-voltage batter y,ch eck the
maximum charging cur rent settings in the
multimedia system menu. Ov Ov
er
ervie
vie w of t
w of t he c
he char
harging cable contr
ging cable contr ol panel
ol panel The
charging cable cont rol panel sho ws the cur-
re nt status of thech arging process. 1
Supply voltage indicator
2 Charging process indicator 3
Temp erature monitor indicator
4 Safety sy stem indicator
Suppl
Suppl y v
y volt
oltag
age indicat
e indicat or
or1
1 Display
Display
Meaning
Meaning
Lights up whit eThe supplyvoltage is
connected. Char
Char
ging pr
ging pr ocess indicat
ocess indicat or
or2
2 Display Display
Meaning Meaning
Flashes green The high-voltage bat-
tery isch arging. 200
200
Driving and parking

T
T
em
em per
per atur
atur e contr
e contr ol indicat
ol indicat or
or3
3 Display
Display
Meaning
Meaning
Lights up redT hegreen LED 0ashes
simultaneousl y:ove r-
te mp erature – the
ch arging per form ance
is reduced.
The green LED does
not 0ash: overtemper-
ature – thech arging
process is stopped.
Flashes redO vertemperature at
th e mains plug – the
ch arging process is
stopped. Safe
Safe
ty syst
ty syst em indicat
em indicat or
or4
4 Displ
ay
Display Meaning
Meaning
Flashes redC harging cable mal-
function – cann ot
car ryout thech arging
process, reset the
ch arging cable operat-
ing unit.
Lights up redW hite LED is o.:
po we r supply malfunc-
tion – cannot car ry
out thech arging proc-
ess, replace the mains
soc ket.
White LED is on: vehi-
cle malfunction – can-
not car ryout the
ch arging process,
re set thech arging
cable operating unit. When all
four displa yslight up, thech arging cable
operating unit per form s a self-test. If
te mp erature monitor 3indicates a malfunc-
tion, it may help toprotect thech arging cable
from direct sunlight.
T T o r
o r ese
ese t t
t the c
he c har
harging cable oper
ging cable oper ating unit:
ating unit:if
saf ety sy stem 4indicates a charging cable mal-
function or a vehicle malfunction, /rst reset the
ch arging cable operating unit. Todo this, discon-
nect thech arging cable from theve hicle and from
th e mains soc ket and waitfor appr oximately /ve
seconds. If the malfunction persists aTer the
ch arging cable is reconnected, charging at the
mains soc ket is not possible. The charging cable
must be replaced or theve hicle plug must be
ch ecked at a quali/ed specialist workshop,
depending on the indicator. F
F
unctions of t
unctions of t he indicat
he indicator lam
or lamps on t
ps on t he v
he vehicle
ehicle
soc ket
soc ket %
Depending on the national version, your vehi-
cle is equipped with one of thefo llowing vehi-
cle soc kets.
The soc ket 0ap is centrally loc ked and unloc ked
to get her with theve hicle. Driving and parking
201
201

Combo 1
vehicle soc ket
1 Socket lamp
2 Charging process indicator lamp
3 Locking status indicator lamp Combo 2
vehicle soc ket
1 Socket lamp
2 Charging process indicator lamp
3 Locking status indicator lamp
Soc ket lamp 10ashes or lights up as with indi-
cator lamps 2and 3. Ov
Ov
er
ervie
vie w of t
w of t he loc
he loc king st
king st atus
atus Loc
Loc
king st
king st a-
a-
tus
tus 3
3 Display
Display
Meaning
Meaning
% Lights up
white Ve
hicle
soc ket
unloc ked,
insert or
re mo vecharg-
ing cable
% Flashes whiteMalfunction
during locking
or unlocking Ov Ov
er
ervie
vie w of t
w of t he c
he char
harging pr
ging pr ocess st
ocess st atus
atus S
S
t
tatus of t
atus of t he
he
c
c har
har ging
ging
pr
pr ocess
ocess 2
2 Displ
ay
Display Meaning
Meaning
# Flashes
orangeConnection is
being estab-
lished
# Flashesgreen Active energy
0ow 202 202
Driving and parking

S
S
t
tatus of t
atus of t he
he
c
c har
har ging
ging
pr
pr ocess
ocess 2
2 Displ
ay
Display Meaning
Meaning
# Lights up
orangeInter
ruption in
ch arging
# Lights up
green Charging
process com-
ple
ted
# Flashesred
(for appr ox.
90 s) Ve
hicle mal-
function;
ch arging is
not possible S S
t
tar
ar ting t
ting t he alt
he alt er
ernating curr
nating curr ent c
ent char
harging pr
ging pr ocess
ocess
(mode 2/3)
(mode 2/3) &
D
DAN
AN GER
GER Risk of death when charging at a
damaged soc ket
The charging process uses high voltage. If
th ech arging cable, theve hicle soc ket or the
mains soc ket are damaged, you could receive
an elect ric shoc k. #
Only use an undamaged charging cable. #
Avoid mechanical damage such as crush-
ing, abrading or driving overth e cable. #
Have a damaged vehicle soc ketre placed
at a quali/ed specialist workshop as
soon as possible. #
Never connect thech arging cable to a
damaged vehicle soc ket. *
N
NOOTE
TE Damage due toove rheating of
ch arging cable and charging cable con-
nector During
thech arging process, thech arging
cable and charging cable connector can heat
up within their permissible limit values. The permissible limit
values are in0uenced by
th efo llowing factors:
R the po wer supply system and thech arging
cable are not damaged
R the inst ructions for handling thech arging
cable and the control element on the
ch arging cable ha vebeen obser ved #
Ifth ech arging cable or charging cable
connector becomes too hot, ha vethe
po we r supply system checked. *
N NOOTE TE Damaged or dirty vehicle soc ket
when the soc ket 0ap is open #
Alwayske ep the soc ket co ver and the
soc ket 0ap closed when there is no
ch arging cable connected. This pr otects
th eve hicle soc ket from dirt and damage. #
Make sure that the soc ket co ver is
closed proper lybefore closing the soc ket
0ap. This can otherwise result in damage
which may pr event the soc ket 0ap from
being opened again. Driving and parking
203
203

*
N
NO
OTE
TE Damage totheve hicle soc ket or the
ch arging cable connector due toincor rect
handling Do not use
excessive forc e (maximum 300 N)
to insert thech arging cable connector into the
ve hicle soc ketto the stop. You may otherwise
damage theve hicle soc ket,thech arging cable
connector or their contacts. #
Ifyo ufe el there is increased resis tance,
pull thech arging cable connector out of
th e soc ket and reinsert it. R
R
eq
eq uir
uir ements:
ements:
R The transmission is in position j.
R The vehicle is unloc ked or the distance
between theke y and theve hicle does not
ex ceed 1 m.
R The vehicle is switched o.. The õdisplay
in the Instrument Display is o..
R The charging cable is not taut. Depending on
theve hicle's equipment and on the
national version, your vehicle is equipped with one
of thefo llowing vehicle soc kets:
R Type 1 forch arging with alternating cur rent
(mode 2 or 3)
R Combo 1 forch arging with alternating cur rent
(mode 2 or 3) and charging with direct cur rent
(mode 4)
R Type 2 forch arging with alternating cur rent
(mode 2 or 3)
R Combo 2 forch arging with alternating cur rent
(mode 2 or 3) and charging with direct cur rent
(mode 4) Combo 1
vehicle soc ket 204
204
Driving and parking

Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% Vehicles with a vehicle soc ket combo requ ire
only connection 8forth ech arging cable
connector. Open only the upper part of soc ket
co ver5. #
Tocharge at a mains soc ket, insert the mains
plug into the mains soc ket of theex tern al
po we r source tothe stop and set the maxi-
mum charging cur rent if requ ired
(/ page 199). #
Insert thech arging cable connector into vehi-
cle soc ket connection 8tothe stop. If the
wa llbox/charging station is not equipped with
a ch arging cable, inse rtthe plug of theve hi-
cle's charging cable into thewa llbox/charging
station soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted. The
# indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d.
% Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Driving and parking
205 205