2020 MERCEDES-BENZ SPRINTER light

#
Adjust the seat into the desired position. #
Press memory button M toge ther with one of
th e preset position buttons 1,2 or 3.
An acou stic signal sounds. The settings are
st ored. #
Tocall up: press and hold there leva nt preset
position button 1,2 or 3 until the front seat is
in thestored position. Ro
tating the front seats &
WARNING Risk of inju ryor death if the
driver's seat and front-passen ger seat
are not engaged
If th e driver's and front-passenger seats are
not engaged in the direction of tr avel during
th e trip, there stra int sy stems cann otoffer
pr otection as intended. #
Enga gethe driver's and front-passenger
seat in the direction of tr avel before the
engine is star ted. &
WARNING Risk of inju ryfrom adju sting
th eve hicle settings while theve hicle is in
motion
Yo u could lose control of theve hicle in the
fo llowing situations:
R ifyo u adjust the driver's seat, the head
re stra int, thesteering wheel or the mir ror
while theve hicle is in motion
R ifyo ufast enyour seat belt while theve hi‐
cle is in motion #
Before starting the engine: adjust the
driver's seat, the head restra int, the st
eering wheel or the mir ror and fasten
yo ur seat belt. Yo
u can rotate the driver's and front passenger
seat 50° and 180°. The seats engage bo thin and
opposite tothe direction of tra vel as well as at
50° totheex it. #
Ensure that the parking brake is applied and
th e brake le ver is folded down wards as far as
it will go (/ page141). #
Adjust thesteering wheel in such a wayth at
th ere is suf ficient free space torotate and
adjust the driver's seat (/ page76). #
Slide the front passenger seat forw ard before
ro tating it (/ page 64). #
Torotate the seat: push lever1 towa rds
th e door and rotate the seat slightly in wards.
The rotation device is unloc ked. #
Release le ver1 again. #
Rotate the seat byaround 50° out wards or
in wa rds into therequ ired position. 70
Seats and stowage

Fo
lding the co-d rive r bench seat cushion for‐
wa rds and backwards #
Tofold the seat cushion forw ards: liftthe
seat cushion out of front anchorage 1.#
Pull the seat cushion out of rear anchorage
2 and mo veit slightly forw ards. #
Foldthere ar edge of the seat cushion
upwards.
% Yo
u can stowindividual objects in thestow‐
age space beneath the co-driver bench seat. #
Tofold the seat cushion backwards: fold
th ere ar edge of the seat cushion down wards. #
Slide the seat cushion under the seat back‐
re st into rear anchorage 2. #
Push the front seat cushion down wards until
it engages in front anchorage 1.Ad
justing armrests Example ima
ge #
Toset the armrest inclination: fold the arm‐
re st more than 45° upwards 2.
The armrest will be unlo cked. #
Foldthe armrest forw ards 3asfar as it will
go. #
Slowly fold the armrest upwards into the
re qu ired position. #
Tofold the armrest up wards: if necessar y,
fo ld the armrest more than 90° upwards 1. Fo
lding thefo lding seat up or down &
WARNING Risk of inju rywhen using the
fo lding seat due toinser tedkey
When theke y is in the lock of the partition
sliding door, it can come into contact with the
person on thefo lding seat. #
Alwaysre mo vetheke y from the parti‐
tion sliding door before a person sits on
th efo lding seat. #
Remo vekey1 from the partition sliding
door. #
Press the push button on catch 2and fold
seat cushion 3up or down. #
Release push button on cat ch2 when seat
cushion 3reaches its end position. #
Moveseat cushion 3until it has loc ked. The
push button on catch 2must be comple tely
fl ush with the seat frame. Seats and
stowage 71

#
Installth eth re e-person rear ben chseat on
th ird row of seats 3. #
Installth efo ur-pe rson rear ben chseat on
fo ur th row of seats 4. Ve
hicles with thre erow s of seats
1 Firstrow of seats
2 Second rowof seats
3 Third rowof seats: four-pe rson rear ben ch
seat with strut #
Installth efo ur-pe rson rear ben chseat on
th ird row of seats 3.
Re moving the rear ben chseat Pe
rform these tasks carefully with the assis tance
of a second pe rson. #
Toremo vethe co vers of the mounting
shells: push clip 1inthe direction of the
ar row and de tach cover2 bypushing tothe
to pre ar at an angle. #
Push release handle 2forth e bench seat all
th ewa y down and hold it there while tilting
th e bench seat backwards slightly at the
same time using there lease handle and pull it
slightly backwards. #
Let go of there lease handle.
The loc kson the bench seat legs will be
unloc ked and red indicator tabs 3 onthe
housing of release handle 2will be visible. #
Hold the unloc ked bench seat bygrab han‐
dles 1and pull backwards slightl y. #
Tilt bench seat 1backwards and pull it out
of the mounting shells.
% If
th e bench seat cann otbe pulled out of the
mounting shells, the bench seat may be
we dged in the seat anchorage. This can hap‐
pen if the bench seat is tilted toofa r back‐
wa rds.
If th e bench seat cann otbe pulled out of the
mounting shells, you can rectify this situation as
fo llo ws: Seats and
stowage 73

#
Tilt th e bench seat forw ards without engaging
it. #
Pull the bench seat backwards again using
re lease handle 2. #
Tilt th e bench seat backwards slightly and
pull it out of the mounting shells. #
Toremo veorstore the bench seat, place it
next tothe mounting shells and roll it towa rds
th ere ar-end doors.
or #
Lift the bench seat out from the side tostore
it.
% It may be necessary
forth e bench seats in
front or behind tobe remo ved. #
Toattach the co vers of the mounting
shells: hold cover3 such that retaining lug
1 is pointing towa rdsre ar seat anchorage
2. #
Insert co ver3 into rear seat anchorage 2
by pushing it down wards at an angle and then
clip it tothe mounting shell. #
Afterre moving there ar ben chseat, ensure
th at there ar ben chseat can stand firm ly and
not tip over when in storage.
Please no tethat the me tallic seat support in the
ve hicle floor will heat up during a journey if the
re ar seating has been remo ved.
Installing there ar ben chseat
Secure engagement of there ar ben chseat is
guaranteed only if youke ep the seat anchorages
clean and free of objects.
% In
vehicles regis tere d as passenger vehicles,
obser vethe maximum permitted number of
seats. #
Remo vethe co vers of the mounting shells as
described under "Removing there ar ben ch
seat". #
Ensure that there are no objects in the seat
anchorages and mounting shells. #
Position the bench seat behind the ins talla‐
tion position. #
Hold the bench seat bythe grab handles and
tilt it backwards. #
Rollth e bench seat forw ards on the le vel
plastic car riers. #
Ensure that there ar legs of the bench seat
are engaged. #
Tilt th e bench seat forw ards firm lyuntil the
loc kson the front legs of the bench seat
engage audibly.
The loc kson the front legs of the bench seat
will now be loc ked and there d indicator tabs
on the housing of release handle 1should
no longer be visible.
% If
th ere d indicator tabs on there lease handle
housing are visible, the bench seat is not cor‐
re ctly engaged.
If th e bench seat is not cor rectly engaged, you
can rectify this situation as follo ws: #
Unlock the bench seat again and tilt it for‐
wa rdsfirm ly until the loc kson the bench seat
front legs engage audibly. #
Attach the co vers of the mounting shells as
described under "Removing there ar ben ch
seat". 74
Seats and stowage

%
Depending on
the head restra int model, indi‐
vidual adjustment options may be omit ted. Switching
the seat heating on and off &
WARNING Risk of bu rns due torepeat‐
edly switching on the seat heating
Re peatedly switching on the seat heating can
cause the seat cushion and seat backrest
padding tobecome very hot.
The health of persons with limited temp era‐
ture sensitivity or a limited ability toreact to
high temp eratures may be af fected or they
may even su ffer burn-like injuries. #
Do not repeatedly switch on the seat
heating. To
protect against overheating, the seat heating
may be temp orarily deactivated af ter it is
switched on repeatedly.
* NO
TEDama getothe seats caused by
objects or documents when the seat
heating is switched on When
the seat heating is switched on, over‐
heating may occur due toobjects or docu‐
ments placed on the seats, e.g. seat cushions
or child seats. This could cause damage to
th e seat sur face. #
Make sure that no objects or docu‐
ments are on the seats when the seat
heating is switched on. Re
quirements:
R The po wer supp lyhas been switched on. #
Toswitch on: press button 1.
All indicator lamps on the button light up. #
Tolowe r the le vel:press button 1until the
re qu ired heating le vel is reached.
Depending on the heating le vel, one tothree
indicator lamps light up. #
Toswitch off: press button 1until all indi‐
cator lamps are off.
% The seat heating automatically switches back
out of
theth re e heating le vels af ter 8, 10and
20 minutes until the seat heating switches
off. Ad
justing the steering wheel &
WARNING Risk of inju ryfrom adju sting
th eve hicle settings while theve hicle is in
motion
Yo u could lose control of theve hicle in the
fo llowing situations:
R ifyo u adjust the driver's seat, the head
re stra int, thesteering wheel or the mir ror
while theve hicle is in motion
R ifyo ufast enyour seat belt while theve hi‐
cle is in motion #
Before starting the engine: adjust the
driver's seat, the head restra int, the
st eering wheel or the mir ror and fasten
yo ur seat belt. &
WARNING Risk of entrapment forch il‐
dren when adjusting thesteering wheel
Children could injure themselves if they
adjust thesteering wheel. #
Never lea vechildren unat tended in the
ve hicle. #
When leaving theve hicle, alw aysta ke
th e SmartK eywith you and lock the
ve hicle. 76
Seats and stowage

#
Toopen: press cup holder 1or2. #
Fold out the cup holder. #
Toclose: slide cup holder 1or2 back in
until it engages. Asht
ray and cigar ette lighter Using asht
rays While driving
#
Place the closed ashtr ayin a cup holder in
th e windshield stowage compartments while
driving. #
Check that the ashtray is seated securely.
% Do not place
the ashtray in the center con‐
sole cup holders. It cann otsit securely here.
Opening #
Fold co ver1 upwards. Using
the cigar ette lighter in the center con‐
sole &
WARNING ‑ Risk of fire and injury from
hot cigar ette lighter
Yo u can burn yourself if youto uch the hot
heating element or the soc ket of the cigar ette
lighter.
In addition, flammable materials may ignite if:
R you drop the hot cigar ette lighter
R ach ild holds the hot cigar ette lighter to
objects, forex ample #
Always hold the cigar ette lighter bythe
knob. #
Always make sure that the cigar ette
lighter is out of reach of children. #
Never lea vechildren unat tended in the
ve hicle. Re
quirements:
R The ignition is switched on #
Press in cigar ette lighter 1.
The cigar ette lighter will pop out when the
heating element is red-hot. Seats and
stowage 79

#
Only connect suitable devices tothe
soc ket. Re
quirements:
R The devices must be equipped with a suitable
plug which con form sto thest andards spe‐
cific tothe count ryyou are in.
R Only devices up toa maximum of 150wa tts
are pe rmitted.
R Do not use multiple soc ket outlets. #
Open flap 3. #
Insert the plug of the device into 115 V soc ket
1 .
When the on-board electrical sy stem voltage
is suf ficient, indicator la mp2lights up.
If yo u will not be using the11 5 V po wer soc ket,
ke ep theflap closed. Using soc
kets in the cargo co mpartment Re
quirements:
R Only devices with a maximum po wer con‐
sum ption of 180 W (15 A) may be connected. #
Fold up co ver1 ofthe soc ket. #
Inse rtthe plug of the device. Charging a mobile phone using
the USB
soc ket in the rear #
Place the mobile phone in stowage compart‐
ment 1and connect it toUSB port 2to
ch arge. Seats and
stowage 81

Exterior lighting
Note
s onchanging the lights when driving
abroad Ve
hicles with halogen or static LED head‐
lamps: Changing the headlamps is not neces‐
sar y.The legal requ irements will also be fulfilled
in countries with left and right-hand traf fic. In
fo rm ation about lighting sy stems and your
re sponsibility The
vehicle's various lighting sy stems are only
aids. The vehicle driver is responsible for adjust‐
ing theve hicle's lighting tothe pr evailing light,
visibilit y,statutory conditions and traf fic condi‐
tions. Light switch
Operating the light switch
#
00470060 Activates or deacti vates parking
lights and license plate and instrument light‐
ing. #
00480058 Activates or deacti vates automatic
driving lights/daytime running lights (p refer‐
re d light switch position). #
00490058 Activates or deacti vates low beam/
high beam. #
4 Activates or deacti vatesfo g light. #
5 005E Activates or deacti vatesre ar fog
light. #
6Applies or releases the electric parking
brake(/ page143)
% If
yo u hear a warning tone when exiting the
ve hicle, the light may still be on. %
The turn signal light,
the high beam and the
high-beam flasher are operated with the com‐
bination switch (/ page 85).
% Leaving
thest anding lights on for se veral
hours drains the batter y.
If th e battery charge isvery low, thest anding
lights will swit choff automatically toenable
th e next vehicle start.
Au tomatic driving lights function &
WARNING Risk of accident when the low
beam is switched off in poor visibility
When the light switch is set to0058 ,th e low
beam may not be switched on automatically if
th ere is fog, snow or other causes of poor vis‐
ibility such as spr ay. #
In such cases, turn the light switch to
0058 . The automatic driving lights are only an aid.
Re
sponsibility forve hicle lighting rests with you.
Tu rn the light switch from 0058to0058 immedi‐
ately in theev ent of fog, snow or spr ay. Other‐
wise, the driving light is temp orarily inter rupte d.
To switch the automatic driving lights on:
R Turn the light switch tothe0058 position.
Switch the po wer supply on: the parking
lamps will automatically switch on or off
depending on the brightness of the ambient
light.
The daytime running la mps are switched on
when the engine is running. The pa rking
lamps and the low beam also switch on or off
depending on the brightness of the ambient
light.
When the low beam is switched on, the0058
indicator lamp on the instrument clus ter will
also switch on.
Switching fog light and rear fog light on or off
Re quirements:
R The light switch is in the0058 or0058 posi‐
tion.
R The po wer supply or the engine has been
switched on. #
Toswitch thefo g light on or off: press but‐
to n7. #
Toswitch there ar fog light on or off: press
button 6. 84
Light and vision