2019 TOYOTA SUPRA lock

300
Supra Owner's Manual5-1. MOBILITY
Place chocks or other suitable
objects in front of and behind the
wheel directly opposite to the one
being changed.
If it is necessary to change a wheel
on a slight downhill slope, place
chocks and other suitable objects,
for example stones, under the
wheels of the front and rear axles in
the opposite direction to the direc-
tion of roll.
The wheel locking bolts have a spe-cial coding. The blots can only be
released with the adapter that
matches the coding.
The adapter of the thiefproof wheel
studs can be found in the on-board
tool kit or in an oddments tray in the
on-board tool kit.
• Wheel stud, arrow 1.
• Adapter, arrow 2.
1Place the adapter on the wheel
stud.
2Unscrew the wheel stud.
3After unscrewing the wheel
stud, remove the adapter again.
1Place the adapter on the wheel
stud. If necessary, turn the
adapter until it fits on the wheel
stud.
2Screw on the wheel stud. The
tightening torque is 140 Nm. On a level surface
On a slight downhill slope
Thiefproof wheel studs
Principle
Overview
Unscrewing
Screwing on

302
Supra Owner's Manual5-1. MOBILITY
closest to the wheel to be
changed.
3Turn the jack crank or lever
clockwise to extend the jack.
4Remove your hand from the jack
as soon as the jack is under
load and continue to turn the
jack crank or lever with one
hand.
5Make sure that the base of the
vehicle jack is extended perpen-dicular to and at right angles
underneath the jacking point.
6Make sure that the base of the
jack is extended perpendicular
to and at right angles below the
jacking point.
7Raise by cranking until the jack
is supported on the ground with
its entire surface and the wheel
in question is at most 3 cm, 1.2
inches off the ground.
Only fit one emergency wheel at
most, as required.
1Unscrew the wheel studs.
2Remove the wheel.
3Put on the new wheel or emer-
gency wheel and tighten at least
Fitting a wheel

303
5
Supra Owner's Manual5-1. MOBILITY
MOBILITY
two wheel studs crosswise until
finger-tight.
If non-original light alloy wheels not
from the vehicle manufacturer are fit-
ted, the wheel studs belonging to the
wheels may also have to be used.
4Tighten the remaining wheels
tuds until finger-tight and then
tighten all the wheel studs
crosswise.
5Turn the jack crank anticlock-
wise to retract the jack and
lower the vehicle.
6Remove the jack and stow it
securely.
1Tighten the wheel studs cross-
wise. The tightening torque
is140 Nm, approximately 101 lb
ft.
2Stow the faulty wheel in the
boot, if necessary.
Due to its size, the faulty wheel cannot
be accommodated under the boot floor.
3Check tyre inflation pressure at
the next opportunity and correct
as necessary.
4Reset the Tyre Pressure Monitor
(TPM).
5Check the tight fit of the wheel
studs using a calibrated torque
wrench.
6Drive to the nearest any author-
ized Toyota retailer or Toyota
authorized repairer, or any relia-ble repairer to have the dam-
aged tyre replaced.
In case of a flat tyre, the emergency
wheel can be used as a replace-
ment for the defective tyre. The
emergency wheel is intended for
short-term use until the defective
wheel has been replaced.
Only fit one emergency wheel at
most.
Additionally, regularly check the
tyre inflation pressure of the emer-
gency wheel in the boot and correct
the pressure if necessary. After changing the wheel
Emergency wheel
Principle
General
Safety note
WARNING
The emergency wheel has special
dimensions. When driving with an
emergency wheel, the driving proper-
ties may change, for example
reduced directional stability when
braking, longer braking distance and
modified self-steering behaviour in
the limit range. There is a danger of
accidents. Drive with care and do not
exceed a speed of 80 km/h, 50 mph.

306
Supra Owner's Manual5-1. MOBILITY
1Pull the lever, arrow 1.
The bonnet is released.
2After releasing the lever, pull the
lever again, arrow 2.
The bonnet is opened.
Bonnet
Safety notes
WARNING
Incorrectly performed work in the
engine compartment can damage
components and lead to a safety risk.
There is a danger of accidents or
damage to property. Have work in the
engine compartment undertaken by
any authorized Toyota retailer or
Toyota authorized repairer, or any reli-
able repairer.
WARNING
The engine compartment contains
moving components. Certain compo-
nents in the engine compartment can
also move when the vehicle is
switched off, for example the radiator
fan. There is a danger of injury. Do
not reach into an area where there
are moving parts. Keep articles of
clothing and hair away from moving
parts.
WARNING
The bonnet has protruding parts on
the inside, for example locking hooks.
There is a danger of injury. When the
bonnet is open, watch out for protrud-
ing parts and keep these areas clear.
WARNING
If the bonnet is not correctly locked, it
can come open during the journey
and impair visibility. There is a danger
of accidents. Stop immediately and
close the bonnet correctly.
WARNING
Parts of the body can become
trapped when opening and closing
the bonnet. There is a danger of
injury. When opening and closing,
make sure that the area of movement
of the bonnet is kept clear.
NOTICE
When wipers are folded away from
the windscreen, they can be trapped
when the bonnet is opened. There is
a danger of damage to property.
Before opening the bonnet, make
sure that the wipers with wiper blades
fitted are in contact with the wind-
screen.
NOTICE
When closing, the bonnet must lock
into place on both sides. Applying
additional pressure can damage the
bonnet. There is a danger of damage
to property. Open the bonnet again
and close it firmly. Avoid applying
additional pressure.
Opening

311
5
Supra Owner's Manual5-1. MOBILITY
MOBILITY
1Open the bonnet, see page 306.
2Turn the cap anticlockwise to
open.
3Add engine oil.
4Tighten cap.
Engine oil quality is a crucial factor
determining the lifetime of the
engine.
Only replenish with the types of
engine oil that are listed.
Some engine oil grades may not be
available in all countries.Replenish with engine oils with the
following oil specifications.
If suitable engine oils are not avail-
able, up to 1 litre, approximately 2
pints, of an engine oil with the fol-
lowing oil specification can be used
for topping up:
When selecting an engine oil, make
sure that the engine oil belongs to
one of the following viscosity
classes: Adding engine oil
Engine oil grades for topping
up
General
Safety notes
NOTICE
Oil additives can damage the engine.
There is a danger of damage to prop-
erty. Do not use oil additives.
NOTICE
Using the wrong engine oil can result
in engine malfunctions and damage.
There is a danger of damage to prop-
erty. When selecting the engine oil,
make sure that the engine oil corre-
sponds to the oil specification.
Suitable engine oil grades
Petrol engine
TOYOTA GENUINE MOTOR OIL SN
0W-20 C5 for TOYOTA Supra
Alternative engine oil grades
Petrol engine
ACEA C2.
ACEA C3.
Viscosity classes
Viscosity classes
SAE 0W-20.
SAE 5W-20.
SAE 0W-30.

313
5
Supra Owner's Manual5-1. MOBILITY
MOBILITY
1Allow the engine to cool down.
2Open the bonnet, see page 306.
3Turn cap on coolant tank slightly
anticlockwise, then allow the
pressure to escape.
4Open cap on coolant tank.
5The coolant level is correct if it is
just below the Max. mark in the
filler neck.
6Tighten cap.
1Allow the engine to cool down.
2Open the bonnet, see page 306.
3Turn cap on coolant tank slightly
anticlockwise, then allow the
pressure to escape.
4Open cap on coolant tank.
5If necessary, slowly top up to the
correct level; do not overfill.
6Tighten cap.
7Have the cause of coolant loss
rectified as soon as possible.
■Disposal
When disposing of coolant and
coolant additives, comply with the
relevant environmental protection
regulations.
All washer jets are supplied from
one tank.
Use a mixture of tap water and
screenwash concentrate for the
windscreen washer system, if nec-
essary with the addition of anti-
freeze.
Recommended minimum fill level: 1
litre, 1.7 Imp. pints. Checking the coolant level
Topping up
Washer fluid
General
Safety notes
WARNING
Some antifreezes can contain toxic
substances, and are flammable.
There is a risk of fire and fatal injury.
Please comply with the instructions
on the containers. Keep antifreezes
away from sources of combustion. Do
not pour service products into other
bottles. Keep service products out of
the reach of children.

317
5
Supra Owner's Manual5-1. MOBILITY
MOBILITY
ment will perform all of the scheduled
maintenance on your vehicle reliably
and economically.
Rubber hoses (for cooling and heater
system, brake system and fuel system)
should be inspected by a qualified tech-
nician according to the Toyota mainte-
nance schedule.
Rubber hoses are particularly important
maintenance items. Have any deterio-
rated or damaged hoses replaced
immediately. Note that rubber hoses
will deteriorate with age, resulting in
swelling, chafing or cracking.
No maintenance work other than
normal maintenance is required to
keep the emission levels of your
vehicle within the design limits.
Devices connected to the OBD
socket trigger the alarm system
when the vehicle is locked.
Remove any devices connected to
the OBD socket before locking the
vehicle.The OBD socket for checking emis-
sions-relevant components is
located on the driver's side.
For Australia/New Zealand:
maintenance
Socket for on-board diagno-
sis OBD
General
Safety note
NOTICE
Incorrect use of the OBD on-board
diagnosis socket can result in mal-
functions in the vehicle. There is a
danger of damage to property. Only
have service and maintenance work
involving the OBD on-board diagnosis
socket carried out by any authorized
Toyota retailer or Toyota authorized
repairer, or any reliable repairer or
other authorised persons. Only con-
nect devices that have been tested
and found to be safe for use with the
OBD on-board diagnosis socket.
Position

326
Supra Owner's Manual5-1. MOBILITY
This chapter describes all standard,
country-specific and special equip-
ment available for the model series.
It may therefore describe equip-
ment and functions which are not
installed in your vehicle, for exam-
ple on account of the optional
equipment selected or the country
specification. This also applies to
safety-relevant functions and sys-
tems. Please comply with the rele-
vant laws and regulations when
using the corresponding functions
and systems.
The on-board tool kit is located on
the right in the boot, under a cover.
Unlock the cover on the right-hand
side trim, arrow 1, and open, arrow
2.1To replace the wiper blades,
move the wipers to the fold-out
position, see page 142.
2Lift the wipers completely away
from the windscreen.
Replacing parts
Vehicle equipment
On-board tool kit
Wiper blades
Safety notes
NOTICE
The windscreen may sustain damage
if a wiper falls onto it without the wiper
blade fitted. There is a danger of
damage to property. Hold the wiper
firmly when changing the wiper blade.
Do not fold in or switch on the wiper
without a wiper blade installed.
NOTICE
When wipers are folded away from
the windscreen, they can be trapped
when the bonnet is opened. There is
a danger of damage to property.
Before opening the bonnet, make
sure that the wipers with wiper blades
fitted are in contact with the wind-
screen.
Replacing the front wiper
blades