2018 MITSUBISHI ASX Owner's Manual (in English)

Interrupt display screen (whenthe ignition switch or the oper- ation mode is OFF)
E00520500616
When there is information to be announced,
such as lamp reminders, the buzzer sounds and the multi-information display switches to the warning display screen. Refer to the ap-
propriate page and take the necessary meas- ures.
When the cause of the warning display is
eliminated, the warning display goes out au- tomatically.
Refer to “Warning display list (when the ig-
nition switch or the operation mode is OFF)” on page 5-28.
Type 1Type 2
1- Information generated
2- Cause eliminated
To return to the screen dis-
played before the warning dis-
play
Even if the cause of the warning display is
not eliminated, you can return to the screen
that was displayed before the warning dis-
play.
If you press the multi-information meter switch, the display screen switches to the
screen that was displayed before the warning display and the
mark (A) is displayed.
Type 1Type 2
NOTEl Warning display screens with a “” or “”
mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the multi-informa-tion meter switch as follows.
“
”: Press lightly.
“
”: Press for about 2 seconds or more.
Redisplay of a warning display screen
When the mark is displayed, if you lightly
press the multi-information meter switch a
few times, the warning display screen you switched from is displayed again.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-05.
Multi-information display
5-07OGAE18E1Instruments and controls5

Door ajar warning displayscreen (when the ignition switch or the operation mode isOFF)
E00520600473
If any of the doors or the tailgate is not com-
pletely closed, this displays the open door or tailgate.
Type 1Type 2
1- Doors and tailgate are closed
2- Doors or tailgate are open
Information screen (when the
ignition switch is turned fromthe “LOCK” position to the“ON” position or the operation mode is changed from OFF toON)
E00520702234
When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, the display screen switches in the fol-
lowing order.
1- Screen when the ignition switch or the operation mode is OFF
2- System check screen
3- Screen when the ignition switch or the operation mode is ON
System check screen
When the ignition switch is turned to the
“ON” position or the operation mode is put in
ON, the system check screen is displayed for about 4 seconds. If there is no fault, informa- tion screen (when the ignition switch or the
operation mode is ON) is displayed.
If there is a fault, the screen changes to warn-
ing display.
Refer to “Warning display list (when the ig-
nition switch or the operation mode is ON)”
on page 5-31.
NOTEl The system check screen display varies de-
pending on the customer’s equipment.
Multi-information display
5-08OGAE18E1Instruments and controls5Type 1
Type 2 Type 1 Type 2

Service reminder
When the time for periodic inspection ar-rives, the warning display is displayed for a
few seconds after the ignition switch or the operation mode ON screen. Refer to “Service
reminder” on page 5-16.
Type 1
Type 2
Drive mode indicator display
screen*
E00520800303
Type 1Type 2
This displays the 4WD status.
If you select “4WD LOCK” mode with the drive mode selector, “4WD LOCK” is dis-played; if you select “4WD AUTO” mode,
“4WD” is displayed.
Nothing is displayed when 2WD mode is se- lected. Refer to “Drive mode-selector” on
page 6-39. mark display screen (when
the ignition switch or the oper- ation mode is ON
E00520900333
This is displayed when you
press the multi-information meter switch and switch the
warning display screen.
This mark is also displayed if there is another warning
other than the one displayed.
When the cause of the warning display is
eliminated, the
mark goes out automatical-
ly.
NOTEl When the mark is displayed, the warning
display screen can be redisplayed on the in- formation screen.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-05.
Refer to “Information screen (when the igni- tion switch or the operation mode is ON)”
on page 5-10
Multi-information display
5-09OGAE18E1Instruments and controls5

Information screen (when theignition switch or the operation mode is ON)
E00521100576
Each time you lightly press the multi-infor-
mation meter switch, the display screenswitches in the following order.
Type 1Type 2When there is no warning displayWhen there is no warning displayWhen there is a
warning displayWhen there is a
warning display
1- Odometer (Type1)/Tripmeter
2- Odometer (Type1)/Tripmeter
3- Service reminder
4- Engine coolant temperature display
(Type 1)
5- Driving range display (Type 1)
6- Average speed display, average fuel
consumption display, momentary fuel
consumption display (Type 1)
7- Driving range display, momentary fuel
consumption display (Type 2)
8- Average fuel consumption display, mo-
mentary fuel consumption display (Type 2)
9- Average speed display, momentary fuel
consumption display (Type 2)
10- Function setting screen
11- Redisplay of a warning display screenNOTEl While driving, even if you operate the multi-
information meter switch, the function set- ting screen is not displayed. Always stop thevehicle in a safe place before operating.
Refer to “Changing the function settings
(when the ignition switch or the operation mode is ON)” on page 5-19.
l When there is information to be announced,
such as a system fault, the buzzer soundsand the screen display is switched.
Refer to “Interrupt display screen (when the
ignition switch or the operation mode is ON)” on page 5-14.Odometer/Tripmeter
E00568400046
The operation method is the same as when
the ignition switch or the operation mode is OFF.
Refer to “Odometer/Tripmeter” for further details on page 5-06.
Multi-information display
5-10OGAE18E1Instruments and controls5 Type 1 Type 2

Service reminder
E00522500694
This displays the distance
and number of months until
the next periodic inspection.
Refer to “Service reminder” on page 5-16.
Type 2Type 1Engine coolant temperature
display
E00521400566
This indicates the engine
coolant temperature.
If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUTIONl If the engine is overheating, “” will blink.
In this case, the bar graph is on the red zone.
lmmediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-04.Driving range display
E00568500047
This displays the approximate driving range
(how many more kilometres or miles you can drive). When the driving range falls below
approximately 50 km (30 miles), “---” is dis-
played.
Refuel as soon as possible.NOTEl The driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.
l When you refuel, the driving range display
is updated.
However, if you only add a small amount of
fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
l On rare occasions, the value displayed for
the driving range may change if you areparked on an extremely steep incline. This is
due to the movement of fuel in the tank and
does not indicate a malfunction.
Multi-information display
5-11OGAE18E1Instruments and controls5 Type 1Type 2 Type 1 Type 2

NOTElThe display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-19.Average speed display
E00568600048
This displays the average speed from the last
reset to the present time.
There are the following 2 mode settings.
For the method for changing the average speed display setting, refer to “Changing the
function settings (when the ignition switch or
the operation mode is ON)” on page 5-19.
Manual reset mode
l When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed
displayed at that time is reset.
l When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system]
Turn the ignition switch from the
“ACC” or “LOCK” position to the “ON” position.
[For vehicles equipped with keyless op-
eration system]
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done,
however, the data from the last reset is
displayed.
Auto reset mode l When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed displayed at that time is reset.l When the engine switch or the operation
mode is in the following conditions, the
average speed display is automatically
reset.
[Except for vehicles equipped with key-
less operation system]
The ignition switch is in the “ACC” or “LOCK” position for about 4 hours or
longer.NOTEl The average speed display and the average
fuel consumption display can be reset indi-vidually for the auto reset mode and manual
reset mode.
l “---” is displayed when the average speed
cannot be measured.
l The initial (default) setting is “Auto reset
mode”.
l The display setting can be changed to the
preferred units (km/h or mph).
Refer to “Changing the function settings (when the ignition switch is “ON”)” on page
5-19.
l The memory of the auto reset mode or man-
ual reset mode for the average speed display is erased if the battery is disconnected.Average fuel consumption dis-
play
E00568700137
This displays the average fuel consumption from the last reset to the present time.
Multi-information display
5-12OGAE18E1Instruments and controls5 Type 1 Type 2

There are the following 2 mode settings.
For information on how to change the aver- age fuel consumption display setting, refer to
“Changing the function settings (when the ig- nition switch or the operation mode is ON)”
on page 5-19.

The “” mark (A) in the momentary fuel
gauge shows the average fuel consumption. (Type 2)

Manual reset mode
l When the average fuel consumption is
being displayed, if you hold down the
multi-information meter switch, the average fuel consumption displayed atthat time is reset.
l When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system]
Turn the ignition switch from the
“ACC” or “LOCK” position to the “ON” position.
[For vehicles equipped with keyless op- eration system]
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done,
however, the data from the last reset is displayed.
Auto reset mode
l When the average fuel consumption is
being displayed, if you hold down the multi-information meter switch, the
average fuel consumption displayed at that time is reset.
l When the engine switch or the operation
mode is in the following conditions, the average fuel consumption display is au-
tomatically reset.
[Except vehicles equipped with keyless
operation system]
The ignition switch is in the “ACC” or
“LOCK” position for about 4 hours or
longer.
[For vehicles equipped with keyless op- eration system]
The operation mode is in ACC or OFF for about 4 hours or longer.NOTEl The average speed display and the average
fuel consumption display can be reset indi-vidually for the auto reset mode and manual
reset mode.
l “---” is displayed when the average fuel con-
sumption cannot be measured.
l The initial (default) setting is “Auto reset
mode”.
l The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con-
sumption may vary from the actual fuel con- sumption. Treat the fuel consumption dis-played as just a rough guideline.
l The memory of the auto reset mode or man-
ual reset mode for the average fuel con-sumption display is erased if the battery isdisconnected.
Multi-information display
5-13OGAE18E1Instruments and controls5Type 1 Type 2

NOTElThe display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-19.Momentary fuel consumption
display
E00568800040
While driving, this displays the momentary fuel consumption, using a bar graph.
When the value of momentary fuel consump-tion surpasses the value of average fuel con-
sumption, the momentary fuel consumption
is displayed with a white bar graph. (Type 2)
Be conscious of maintaining the value of mo-
mentary fuel consumption below the value ofaverage fuel consumption, driving with the
bet-ter fuel consumption can be possible.NOTEl When the momentary fuel consumption can-
not be measured, the bar graph is not dis-
played.
l The display setting can be changed to the
preferred units {km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-19.
l It is possible to cancel the green bar graph.
Refer to “Changing the function settings
(when the ignition switch or the operation mode is ON)” on page 5-19.Function setting screen
E00521900271
The “Display language”,
“Temperature unit”, “Fuel consumption unit”, and
“Average fuel consumption
and speed reset method” etc. settings can be modified as
desired.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19 for further de-
tails.
Interrupt display screen (when
the ignition switch or the oper- ation mode is ON)
E00522000673
Warning display
When there is information to be announced, such as a system fault, a sound is emitted and the information screen switches to the warn-
ing display screen.
Refer to the warning list and take the neces- sary measures.
Refer to “Warning display list (when the ig-
nition switch or the operation mode is ON)”
on page 5-31.
When the cause of the warning display is eliminated, the warning display goes out au-tomatically.
To return to the screen displayed before
the warning display
Even if the cause of the warning display is not eliminated, you can return to the screen
that was displayed before the warning dis- play.

Multi-information display
5-14OGAE18E1Instruments and controls5 Type 2Type 1