2018 FIAT 500 brake pads

19
ESC SYSTEM (for versions/markets, where required)
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
ESC system activation
Flashing of the warning light while driving indicates the intervention of the ESC system.
ESC system failure
If the warning light does not go off or stays on together with the LED on the ASR OFF button while driving.
The display will show a dedicated message.
Contact a Fiat Dealership.
Hill Holder failure
This warning light switches on, on some versions together with a dedicated message on the display, in the event of a Hill
Holder system fault.
In this case, contact a Fiat Dealership as soon as possible. Parking sensor fault
The warning light turns on and the dedicated message is shown on the display when a parking sensor fault is detected.
Start&Stop system fault (versions with multifunction display)
A fault of the system is indicated by the warning light switching on. A dedicated message will appears on the instrument
panel.
Airbag warning light fault (for versions/markets, where provided)
The warning light will blink when a fault of the
¬warning light is detected.
ESCESC
BRAKE PAD WEAR
The warning light switches on, together with a dedicated message on the display, if the front or rear brake pads (on
version/markets, where provided) are worn.
In this case have them replaced as soon as possible.
dd
POSSIBLE ICE ON ROAD
The symbol is shown on the display (on some versions together with a dedicated message) when the outside temperature
is equal to or below 3°C.
èè
(versions with
multifunction
display)
(versions with
multifunction
display)

149
43215109876
Check soft top operation while closing and opening; check
of seals and lubrication of canvas sliding side guide
(convertible versions only)
Check handbrake lever travel and adjust, if necessary
Check and adjust clutch pedal travel (0.9 TwinAir 65 HP versions)
Check conditions and wear of front/rear disc brake pads
(for versions/markets, where provided) and operation
of pad wear indicator
Visually inspect condition and wear of the rear drum brake lining
Visually inspect condition of the accessory drive belt(s)
Inspect and if necessary adjust tensioning of accessory drive belt(s)
(for versions without automatic tensioner only)
Visually inspect conditions of toothed timing drive belt
(0.9 TwinAir versions excluded)
Check and adjust tappet clearance (1.2 8V engines)
Check and, if necessary, top up Dualogic gearbox
electro-hydraulic control oil level (2)
Visually inspect condition of: LPG pipes and connectors,
LPG tank fixing (LPG versions only)
Check fuel system operation and parameters using
the diagnosis socket (LPG versions only)
(2) Check to carry out every year for vehicles on the road in countries with particularly severe climates (cold countries)











Thousands of kilometres751501351201059060453015
Thousands of miles4590817263543627189
Years

SERVICING AND CARE
152
43215109876
Check soft top operation while closing and opening;
check of seals and lubrication of canvas sliding
side guide (convertible versions only)
Check handbrake lever travel and adjust, if necessary
Check conditions and wear of front/rear disc brake
pads (for versions/markets, where provided) and
operation of pad wear indicator
Visually inspect condition and wear of the rear drum brake lining
Inspect and if necessary adjust tensioning of accessory drive belt(s)
(for versions without automatic tensioner only)
Visually inspect condition of the accessory drive belt(s)
Change engine oil and replace oil filter (2)
Replace accessory drive belt(s) (3)
(2) The engine oil and filter change interval depends on driving conditions and is signalled by a warning light or message on the instrument
panel. In any case, it must never exceed 2 years. If the vehicle is mainly used in towns and cities, change the engine oil and filter every year.
(3) Areas that are not dusty: advised maximum distance 120,000 km. The belt must be replaced every 6 years, regardless of distance
travelled. Dusty areas and/or demanding use of the car (cold climates, town use, long periods of idling): advised maximum mileage
60,000 km. The belt must be replaced every 4 years, regardless of distance travelled.
(
❍) Recommended operations
() Mandatory operations





10020018016014012080604020Thousands of kilometres
Thousands of miles6012010896847248362412
Years

161
BRAKES
Depending on the version/market, the
vehicle may be equipped with
mechanical wear detectors for the
brake pads: one for each wheel
assembly.
When the brake linings are close to
wearing out, pressing the brake pedal
will generate a slight squeal: this lasts
for about 100 km (the mileage varies
with the driving style and route).
In this case, it is still possible to
continue driving, with caution.
However, contact a Fiat Dealership as
soon as possible to have the worn
brake pads changed.
WINDSCREEN
WIPER REAR
WINDOW WIPER 41)
Replace the blades if the rubber edge is
deformed or worn. In any case, it is
advisable to replace them
approximately once a year.
LIFTING THE BLADES
WINDSCREEN WIPER
Lift the windscreen wiper arm and
position the blade so that it forms a 90°
angle with the arm;
REPLACING THE
WINDSCREEN WIPER
BLADES
Proceed as follows:
❒ lift the windscreen wiper arm;
❒ press the button A-fig. 144 and
extract the blade C from the arm B;
❒ insert the new blade making sure it
is locked.
REPLACING THE REAR
WINDOW WIPER BLADE
Proceed as follows:
❒ raise the cover A-fig. 145 and
remove the arm from the vehicle by
loosening nut B that fastens it to the
pivot pin;
❒ position the new arm correct and
tighten the nut;
144DVDF0S0129c