2018 AUDI S3 SEDAN Owners Manual

u. 00 .-< N l'­ N .-< 0 N > 00
A WARNING
-The tire pressure monitoring system assists
the driver in monitoring tire pressures . The
driver is responsible for having the tires in­
flated to the correct pressure.
- Do not change the tire pressure when the
temperature of the tire is extremely high.
This could result in serious damage to the
tire and even cause the tire to burst, in­
creasing the risk of an accident.
- A tire with low pressure flexes more. This
heats the tire up too much. This could cause
the tread to separate and even cause the
tire to burst, increasing the risk of an acci­
dent.
- The tire pressure monitoring system does
not warn about damage or defects in the
tire construction that could cause the tire to burst, for example . Inspect your tires regu­
larly .
(D Tips
-If tires are replaced, the sensors/valves do
not need to be removed or replaced. Just re­
placed the valve stem and, if necessary, the
valve and the wheel electronics. If you have
questions, see an authorized Audi dealer or
authorized Audi Service Facility .
- An incorrect display or a malfunction in the
tire pressure monitoring system can occur
after using the tire mobility kit . Have the
sensors replaced by an authorized Audi
dealer or authorized Audi Service Facility.
- For an explanation on conformity with the
FCC regulations in the United States and the
Industry Canada regulations, see
r=;,page 386.
Displaying tire pressures/temperatures
Applies to: vehicles with tire pressure mo nito ring system
Requirement: you must be driving the vehicle.
"'Select in the Infotainment system: the I MENU I
button > Vehicle > left control button > Service
& checks > Tire pressure monitoring > Display
tire pressures.
Wheels
The current tire pressures are shown in green,
yellow or red numbers in the Infotainment sys­
tem:
- Green: the current tire pressure and the speci­
fied tire pressure are approximately the same.
- Yellow: the current tire pressure is too low
compared to the specified tire pressure.
-Red: the current tire pressure is extremely low
compared to the specified tire pressure .
The specified tire pressure is the last tire pres­
sure that was stored
r=;, page 352.
Note that the tire pressure also depends on the
temperature of the tire. The tire pressure in ­
creases as the engine becomes warmer while
driving.
A WARNING
Read and follow the important information
and notes
"*page 350.
(D Tips
The tire pressure or temperature is not dis­
played while the vehicle is stationary and in
adaptation mode. Dashes--.-- are shown in
place of the pressure and temperature.
ill Tire pressure loss
Applies to: vehicles with tire press ure mo nito ring system
-
If the [tE indicator light turns on, the pressure in
at least one tire is too low or new sensors were
not adapted:
RE Indicator light turns on after turning the
ignition on
The tire pressure is too low compared to the
specified pressure .
.,. Check and store the tire pressure(s) the next
time it is possible
"*page 352.
RE Indicator light turns on while driving
Wheels with new sensors were not adapted or
the tire pressure has reached a critical level com­
pared to the specified pressure.
"'Avoid unnecessary steering and braking maneu-
vers.
..,_
351

Wheels
~ Adapt your driving style to the situation.
~ Stop as soon as possible and check the tire(s) .
~ If it is possible to continue driving, see an au-
thorized Audi dea ler or authorized Audi Service
Facility immediately and have your tire(s) re­
paired or replaced.
A WARNING
Read and follow the important information
and
notes ~ page 350.
Storing new tire pressures
App lies to: ve hicles w ith tire press ure m on itoring system
Correctly stored tire pressure specifications are
necessary for reliable tire pressure monitoring.
-
It is always necessary to store the tire pressures
when the tire pressures are modified, for exam­ ple due to a change in load. or when new sensors
are installed .
~ Before storing the tire pressures, make sure the
tire pressures of all four tires meet the speci­
fied values and are adapted to the load
~ page 341, fig . 2 78 . Only correct and store
the pressure in tires whose temperature is ap­
prox imat ely the same as the ambient tempera­
ture .
If the temperature of the tire is higher
than the ambient air temperature, the tire
pressure must be increased approximate ly
3 .0 PSI (0 .2 bar) above the va lue on the sticker .
~ Switch the ignition on.
~ Select in the Infotainment system: IMENUI but­
ton
> Vehicle > left control button > Service &
checks > Tire pressure monitoring > Store tire
pressure > Yes, store now .
After storing the
tire pressu res, the t ire pressu re monitoring sys­
tem measures the current pressures wh ile driv­
in g and stores them as the new specified pres­
sures.
~ If the changed tire pressures are not displayed
in the Infotainment system, drive the vehicle
for approximate ly 10 minutes so that the sen­
sor signal from the wheels is received again.
During this adaptation phase, --.-- is displayed
for the pressure and temperature and the tire
pressure mon itor ing system is only partially
ava ilable. It only provides a warning if one or
352 more
tire pressures is below the minimum per­
mitted specified pressure.
If the
[I] ind icator light turns on and the mes­
sage
Tire pressure : wheel change detected .
Please check all tires and store pressures in
MMI also appears, the system has detected that
the position of the sensors has changed because
of a tire rotation, or that new sensors were in­
stalled. Store the new tire pressures.
A WARNING
Read and follow the important information
and notes
~pag e 350.
Malfunctions
Applies to: vehicles with t ire pressure mo nitori ng syste m
If the tire pressure monitoring system is not
available, t he
mm in dicator light appears in the
instr umen t cluste r display along with the mes­
sage
Tire pressure : malfun ction! See owner's
manual.
-
If the ffim ind icator light appears after switch­
in g the ignitio n on or wh ile dr iving and the
[IJ in­
dicator light also blinks for approximately one
minute and then stays on, there is a system ma l­
function . The fo llowing are examples of situa­
tions that could cause a malfunction:
- If the message appears at the end of the adap ­
tation phase, the system may not detect one or
several of the whee l sensors necessary for pres­
sure monitoring. This may res ult from one or
more whee ls being installed without wheel sen­
sors or with incompatible wheel sensors.
- A wheel sensor or another component has
fa iled.
- Using snow chains can affect the function of
the system because of the shielding effect of
the chains.
- The tire pressure monitoring system is not
avai lab le due to a ma lfunction.
- Transmitters with the same frequency, such as
headphones or remote-controlled devices, may
cause a temporary system malfunct ion due to
the strong electromagnetic field.
.,.

u. 00 .-< N l'­ N .-< 0 N > 00
The @m indicator light and t he message tu rn o ff
once the tire pressure monitoring system is ava il­
ab le aga in . If yo u can not cor rect the ma lf u nct io n
and the
mm indicator lig ht stays on, dr ive imme­
d iate ly to an author ized A udi dealer or autho r­
i zed A udi Service Fac ility to have the ma lfunction
repaired .
Wheels
353

Care and cl eaning
Care and cleaning
General information
Applies to: vehicles with plug-in hybrid drive: for
additiona l cleaning and care information, see
¢ page 117.
Reg ula r, prope r ca re helps to maintai n your veh i­
cle's value. It can a lso be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The ne cessary care prod ucts c an be ob tained
from an authorized Aud i dea ler o r authorized
Audi Service Facility. Read and follow the instruc ­
tions fo r use on the packaging.
A WARNING
- Us ing clean ing and ca re products incorrectly
can be dangero us to your hea lth.
- Always store clean ing and ca re products out
of reach of children to reduce the r is k of po i­
so ning.
@ For the sake of the environment
- Prefe rab ly purchase environmenta lly-friend ­
l y cleaning products.
- Do not dispose of leftove r cleaning and ca re
p roducts wit h house hold trash.
Car washes
The longer that deposits s uch as insects, bird
droppings, tree sap or road salt remain on the ve ­
h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight increase the damaging effect .
Before washing, rinse
off heavy deposits with
p lenty of water.
S tu bborn deposits s uch as bird d roppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
A lso, wash t he u nderside of yo ur vehicle once
road sa lt stops being used for the season .
354
Pressure washers
When was hing yo ur vehicle wi th a press ure was h­
er, always follow the operat ing instruct ions pro ­
vided with the pressure washer . This is especia lly
important in regard to the pressure and spraying
distance. Do not aim the spray direct ly at sea ls on
s ide windows, doors, the hood, the luggage com­
partment lid or the panorama g lass roof * or at
tires, rubbe r hoses, insula ting material, the pow­
e r top*, senso rs* o r camera lenses* . Keep a d is­
tance of at least 16 in (40 cm).
Do not remove snow and ice with a p ressure
washer.
Never use cone nozzles o r high press ure nozzles.
The wate r temperatu re must not be above 140 °F
(60 °C).
Automatic car washes
Sp ray off the ve hicle befo re wash ing.
Make su re t hat the wi ndows, the pa norama g lass
roof* and the power top* are closed and the
winds hield wipers a re
off. Fo llow instructions
from the ca r was h operator, espec ia lly if there
a re acc esso ries attached to your ve hicle.
If possible, use car washes that do not have
brushes.
Applies to: RS models
Only use car washes where the veh icle remains
stationary and the washing equipment moves around the vehicle when wash ing and dry ing . Car
washes that move the veh icle t hrough the ca r
wash using a c ha in a re not re commended .
Washing by hand
Clean the ve hicle starting from t he top and work­
i ng down using a soft sponge or cleaning brus h.
U se solvent-free cleaning prod ucts .
Washing vehicles with matte finish paint by
hand
To avo id damaging the paint when washing, fi rs t
r emove d ust and la rge pa rt icles from your vehi­
cl e. Insects, grease spots a nd fingerpr ints are
best re moved w ith a spe cial cleane r fo r m atte
finish pai nt.

u. 00 .-< N l'­ N .-< 0 N > 00
Apply the product using a mic rofiber cloth. To
avoid damaging the paint surface, do not use too
much pressure .
R inse the veh icle t horo u ghly wi th wa ter. Then
clean using a neutra l shampoo and a soft micro ­
fiber cloth.
R inse the veh icle t horo u ghly again and let it a ir
d ry . Remove any water res idue using a ch amois.
A WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­ dents.
-T o reduce the risk of cuts, protect yourself
from sharp metal components when wash­ ing the underbody or the inside of the wheel
hous ings .
-After wash ing the vehicle, the brak ing effect
may be de layed due to mo isture on the
brake rotors or ice in the w inter . This in­
c reases the risk of an acc ident. The brakes
must be d ried fi rst w it h a few careful b rake
app lications.
@ Note
-If you wash t he veh icle in an automatic car
wash, you m ust fold the exterior m irrors in
-
Care and cleaning
to reduce the r isk o f damage to the m irro rs .
Power fo lding exterior mirrors* m ust only
be folded in and o ut using the power fold ing
function.
-T o red uce the risk of paint damage, do not
was h the vehicle in direct s unlight.
-T o red uce the risk of damage, do not was h
the power top * w ith a pressu re washe r.
-T o red uce the risk of damage to the s urface,
do not use insect removing sponges, kitche n
sponges or s imilar items.
-Matte finish painted vehicle components:
-To reduce t he risk of damage to t he sur-
face, do not use pol ish ing agents or hard
wax.
-Neve r use protective wax. It can destroy
the matte finish effect .
-Do not place any st ickers or magnetic
s igns on vehicle parts painted with matte
finish paint. The paint cou ld be damaged
when the stickers or magnets a re re ­
moved.
@ For the sake of the environment
Only wash the veh icle in facilities spec ia lly de­
s igned for that pu rpose. This will reduce the
r isk of di rty wate r contam ina ted with o il from
en te ring the sewe r sys tem.
Cleaning and care information
When clea ning and caring for individua l vehicle
components, refer to the follow ing tables . The
in fo rmat ion conta ined there is s imp ly recom­
mendations . Fo r qu est io ns or for components t
h at are not listed, consult an authorized Aud i
dealer or authorized Audi Service Fac il ity. Also
fo llow the information found
in c:> ,& .
Exterior cleaning
Component Situation
Solution
Wind shield wip er
Deposits soft cloth wi th glass cleane r, ~ page 56
blade s
Headlights /
Deposits Soft sponge with a mild soap solutiona)
Tail light s
Sensors /
Deposits Sensors: soft cloth wit
h solvent -free cleaning solution
camera lenses Camera lenses: soft cloth with a lcohol-free cleaning so lu-
tion
Snow/ice Hand br ush/solven t-free de-icing spray
355

Care and cl eaning
Component Situation Solution
W hee ls
Road salt Water
Brake dust Acid-free special cleaning solution
Ex haust t ail p ipe s Road salt Water, cleaning solution suitab le for stainless steel, if nee-
essary
P ow er t op Deposits Clea n water, power top clean ing prod uct, if necessa ry.
C lean with the grain of the fabric using a soft brush and al -
l ow to air dry .
Wind deflect o r Deposits Water, mild soap solut ion, if necessaryal
Dec orat ive part s/ Deposits Mild soap so
lution al, a cleaning so lution suitable for stain-
trim less stee l, if necessary
Paint Paint damage Refer to the paint numbe r on the veh icle data label, repair
with touch up pa int¢
page 381
Spilled fuel Rinse with water immediately
S urface r ust Rust remover, then protect w ith hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv -
ice Facility .
Corros ion Have it removed by an authorized Aud i dealer or author-
i zed Audi Service Fac ility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No sh ine even though Treat with s uitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks poor
Deposits such as in- Dampen w ith wate r immediately and remove w it h a m icro-
sects, bird dropp ings, fiber cloth
tree sap and road salt
Grease-based con-Remove immediately with a mild soap solution al and a
tam inants such as soft cloth
cosmetics or sunblock
Ca rbon part s Deposits clean the
same way as painted parts ¢ page 354
Decorat ive decal s Deposits Soft sponge with a mild soap so lutional
a ) Mild soap so lution: maxim um two tablespoo ns of neut ra l soap i n 1 quart (1 liter) of water
Int erior cleaning
Component Situation Solution
Wind ows
Deposits Glass cleaner, then
wipe dry
Deco ra tive part s/ Deposits Mild soap solutional
trim
Pla stic part s
Deposits Damp cloth
Heavier deposits M ild soap so lution al, detergent-free p lastic clean ing solu-
tion, if necessa ry
356

u. 00 ... N l'­ N ... 0 N > 00
Care and cleaning
Component Situation Solution
Di spl ays/ins tru·
Deposits Soft cloth with LCD cleaner
men t clus ter
C o ntro ls
Deposits Soft brush, then a soft cloth with a mild soap solution3>
S af ety be lt s Deposits Mild soap solution al, allow to dry before letting them re-
tract
T ex tile s Deposits adhering to Vacuum cleaner
a
rtificial leather , the surface
Alcanta ra Water-based deposits Absorbent cloth and mild soap solutional
such as coffee, tea,
b lood , etc.
Oil-based deposits Apply a mild soap solution
al, blot away the dissolved oil or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such
Specia l stain remove r, blot with absorbent material, treat
as ink, nai l polish, la- afterward with mild soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc.
Na tural l eather F resh sta ins Cotton clot h with a m ild soap so lution3l
Water-based deposits Fresh stains: absorbent cloth
such as coffee, tea, Dried stains: stain remover suitable for leather
blood, etc .
Oi l-based deposits Fresh stains : absorbent cloth and stain remover suitable
such as oil, make-up ,
for leather
etc. Dried stains: grease dissolving spray
Special deposits such Spot remove r su itab le for leather
as ink, na il polish, la -
tex paint, shoe po l-
ish, etc .
Care Regularly apply condit ion ing cream that protects from
light and penetrates into the material. Use specia l co lored
cond itioni ng cream, if necessary.
Car bon part s Deposits clean the same way as plast ic parts
a) M ild soap solut ion : max imu m two tablespoons of neutral soa p in 1 quar t (1 liter) of water
A WARNING
The windsh ie ld may not be treated with wa­
ter-repell ing wi ndsh ield coating agents. Un­
favorable cond it ions su ch as wet ness, dar k­
ness, o r low sun can resul t in increased glare.
Wiper blade chatter is also possib le.
(QJ) Note
- Headlights /tail light s
-
-Never clean headlights or tail lights w ith a
dry cloth or sponge.
- Do not use any cleaning product that con ­
tains alcoho l, because they could cause
cracks to form.
-Wheels
- Neve r use any pa int polish or other abra-
sive mate rials.
- Damage to the protect ive layer o n the
rims such as stone ch ips or sc ratches must
be repai red immediately.
.,.
357

Care and cl eaning
- Camera len se s
- Never use warm or hot water to remove
snow or ice from the camera lens. Th is
could cause the lens to crack .
- Never use abras ive clean ing mater ia ls or
alcohol to clean the camera lens . This
cou ld cause scratches and cracks.
- Pow er top
- Remove bi rd dropp ings immedia tely.
- Never use gasoline, spot remover, ben-
zene, pa int thinne r or other solvents to re­
move.
- Door windows
- Remove snow and ice on windows and ex-
terior mirrors with a p lastic scraper. To
avoid scratches, move the scraper on ly in
one direction and not back and forth.
- Never remove snow or ice from door win­
dows and m irrors using warm or hot water
because this could cause cracks to form .
- To avoid damage to the rear w indow de­
fogger, do not apply any stickers on the
heating w ires on the inside of the window.
- Decorative parts /trim
- Never use chrome care or cleaning p rod-
ucts.
- Paint
-To red uce the risk of scratches, the vehicle
must be free of dirt and dust before pol­
ishing or waxing.
- To prevent paint damage, do not polish or
wax the veh icle in direct sunlight.
- To red uce the risk of paint damage, do not
polish away rust spots.
- Remove cosmetics and sunscreen immedi ­
ately - these could damage the paint.
- Di spla ys/ instrument cluster
- The d isplays/instrument cluster and the
trim surrounding them must not be
cleaned with dry cleaning methods be­
cause they could be scratched .
- Make sure that the instrument cluster is
switched off and has cooled off before
cleaning it .
- Make sure no fluids enter the spaces be­ tween the instrument cluster and the
trim, because that could ca use damage.
35 8
-Controls
- Make sure that no flu ids enter the con-
trols, because this could cause damage .
-Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their compo­
nents chem ica lly or with co rrosive fluids
or solven ts and never allow sharp objec ts
to come into contact with the safety belts .
This could ca use damage to the belt web ­
bing.
- If there is damage to the webbing, the
connections, the retractors or the buckles, have them replaced by an authorized Audi
dealer or authorized Aud i Serv ice Facility .
-Te xtile s/artificial leather / Alcantara
- Never treat art ificial leather/Alcantara
with leathe r ca re products, solvents, floor
polish, shoe polish, spot remove o r similar
p rodu cts.
- H ave a spec ial ist remove stubborn stains
to prevent damage .
-Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the seat .
- Objects w ith sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface .
- Open hook and loop fasteners, for exam ­
ple on clothing, can damage seat covers .
Make sure hook and loop fastene rs a re
closed.
- Na tural leather
- Never treat leather with solvents, floor
polish, shoe polish, spot remover or simi­
lar products.
- Objects with sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the
seat.
- To he lp prevent the leather from fading,
do not leave the vehicle in direct sunlight