2018 AUDI Q5 warning light

Lights and Vision
Exterior Lighting
Switching the lights on and off
--- ----~-----'~
i
Fig. 37 Instrument p anel: l ig ht switc h with buttons
Light switch ·'!:! ·
Turn the light sw itch to the corresponding posi­
tion when the ignition is switched on.
:oo: and the
selected pos ition turn on (except pos ition 0).
0 -The daytime r unning lights automat ica lly t urn
on. In vehicles for certain markets, you can
switch the automatic daytime running lights on
and off in the Infotainment system*.
AUTO
-T he headlights automatically adapt to the
surrounding brightness.
: oo : -Parking lights
io -Low beam headlights
Buttons
When you turn the light switch to the AUTO or
low beam headlight pos ition
io, you can activate
the following functions:
~ o -A ll-weather lights. The headlights automati ­
cally adjust so that there wi ll be less glare, for
examp le when the road surface is wet.
O t -Rear fog lights
Automatic headlight range control system
Your veh icle is equipped with an automatic head ­
l ight range contro l system that re duces g lare fo r
oncoming traffic i f the vehicle load c hanges. The
~ headlight range ad justs automatica lly . ..... N r-­N .....
~ 0 co
Lights and V ision
Audi adaptive light
Appl ies to: vehicles wit h adaptive light
Adaptive ligh t provides better visibili ty whe n it i s
dark by adapting the lights to the road conditions
based on speed , such as on e xpressways, rura l
roads, at intersections, and in c urves. The adap­
t ive light only functions when the light sw itch is
i n the AUTO position .
A WARNING
--Automatic headlights* are on ly intended to
assist the driver. They do not relieve the
driver of responsibil ity to check the head­
lights and to t urn t hem on manua lly based
on t he curren t ligh t and v is ibility condition s.
For examp le, fog canno t be detec ted by the
light sensors. So always switch on the low
beams under these weather co nditions and
when driv ing in the da rk
io .
- To prevent glare for traffic behind yo ur vehi ­
cle, the rear fog lights should only be turned
on in accordance with traff ic regulat ions.
- Always observe legal regulations when
us­
ing the lighting systems desc ribed .
(D Tips
- The lig ht sensor for the automat ic he ad ­
lights * is in the rearview mir ror mount. Do
not p lace any st ickers in this area on the
windshield.
- A warning tone will sound if you open the door when the exte rior lights a re switched
on .
- Only t he front headlights turn on when t he
daytime running lights are switched on *. In
vehicles in certain markets, the tail lights
w ill also turn on .
- In cool or damp weather, the inside of the
head lights, turn signa ls and tail lights can
fog over due to the temperature diffe rence
between the inside and outside . They will
clear shortly afte r swi tching them on . This
does not aff ect the service life of the light­
mg.
45

Lights and Vision
Turn signal and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 38 Turn sig nal and high beam lever
Turn signals¢ Q
N
0 0
> u.. a,
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
switched on.
@ -Right turn signal
@-Left turn signal
The turn signal blinks three times if you just tap
the lever.
High beams and headlight flasher ~D
Move the lever to the corresponding position:
@ -High beams on (vehicles with high beam as­
sistant*¢ page 46)
©-High beams off or headlight flasher
The
II indicator light in the instrument cluster
turns on .
A WARNING
High beams can cause glare for other drivers,
wh ich increases the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
glare for other drivers.
46
High beam assistant
App lies to : vehicles with high beam ass istant
The high beam assistant automatically turns the
high beams on or off depending on the surround­
ing conditions .
A camera on the rearview mirror mount can de­
tect light sources from other road users. The high
beams switch on or off automatically depending
on the posit ion of vehicles driving ahead and on­
coming vehicles, the vehicle speed and other en­
vironmen tal and traffic conditions.
Activating high beam assistant
Requirement: the light sw itch must be set to the
AUTO posit ion and the high beam assistant must
be switched on in the Infotainment system
¢page 47 .
• To act ivate the high beam ass istant, tap the
lever
forward @~ page 46, fig . 38. The Ii] in­
dicator light appears in the instrument cluster
display and the high beams are switched on/off
automatically. If the high beams were com­
pletely or partially switched on, the
SI indica­
tor light turns on .
Switching the high beams on/off manually
If the high beams did not switch on/off automat­
icall y as expected, you may switch them on or off
manua lly instead :
• To switch the h igh beams on manually, tap the
lever
forward @~ page 46, fig. 38. The II in­
dicator light turns on.
• To switch the high beams off manually, pull the
lever back ©¢
page 46, fig. 38. The high beam
assistant is deactivated.
Operating the headlight flasher
• To operate the headlight flasher when the high
beam assistant is activated and high beams are
switched off, pull the lever back ©¢
page 46,
fig. 38.
The high beam assistant remains ac­
tive.
Messages in the instrument cluster display
EIJ Audi adaptive light: malfunction! See own­
er's manual

u co ..... N r-­N .....
~ 0 co
~ Headlight a ssistant : ma lfun ction! See own­
er 's manual
Drive to an autho rized Audi de aler o r a uthorized
Aud i Service Facility immedia tely to have the
mal funct ion corrected. You can still switch the
high beams on or off manually.
i:a Headlight a ssistant : currently unavailable.
Camera view restricted due to surroundings .
See owner 's manual
The camera view is b locked, fo r example by a
s ticker o r debris.
The senso r is located between the interior rear­
view mir ror and the wi ndshield . Do not p lace any
sti cke rs in t his area on the wi ndshi eld.
,& WARNING
High beam assis tan t is only i ntended to assist
th e drive r. The dr iver is still re sponsib le for
contro lling the headlights and may need to
switch them on and off manually depend ing
on light and visib ility conditions. It may be
necessary to ope rate them manua lly in s itua­
tions such as:
- In adverse weather cond itions such as fog,
heavy ra in, b low ing snow or sp raying water .
- On roads where oncoming traffic may be
partially obsc ured, such as expressways .
- W hen there are road users t hat do not have
s ufficient lighting, s uc h as bicyclers o r
vehicles with dirty ta il lamps.
- In tight cu rves and on steep hills .
- In poo rly lit areas .
- Wi th stro ng ref lec to rs, such as s igns.
- I f the area of t he windsh ield near the se nso r
is f ogg ed ove r, dir ty, i cy or covere d w ith a
sti cker.
Adjusting the exterior lighting
The fun ctio ns are adjust ed in the Infotainment
system.
• Select in the Info tainment sys tem: !ME NUI but­
ton
> Vehicle > left contro l butto n > Vehicle
settings > Exterior lighting .
Lights and Vision
Automatic headlights
Yo u ca n adju st the following se ttings in the Au­
tomatic headlights
men u:
Activation time -you can adjust if the a utomat ic
he adlig hts swi tch on
Early , Medium or Late ac­
cording to the sensi tivity of the ligh t se nsor.
Headlight assistant * -you can switch the high
beam assis tan t* on and off.
Entry/exit lighting
When it is dark, the Entry/exit lighting ill umi­
nates the area a round the vehicle when unlocking
the ve hicle and afte r swi tc h ing off the ignit io n
and opening the dr ive r's door.
The
Entry /exit lighting only works when it is
dark and the ligh t sw itch is in the
AUTO position.
Daytime running lights
USA models :
the daytime r unning lig hts can be
switched on/off . Select
On or Off.
Canada model s:
th is fu ncti on canno t be switche d
off. They act ivate au tomatically eac h time the ig ­
nition is switched on.
Emergency flashers
- --- - -- ----
~
Fig . 39 Ce nter console: emergency flasher butto n
The eme rgen cy fla she rs m akes othe r dr iv e rs
aware of your vehi cle in dangerous situa tions.
• Press the ~ button to sw itch t he emergency
fl as he rs on or off.
You can ind icate a lane change or a turn when the
eme rgency flashers are swi tched on by using the
tu rn s ignal leve r. T he emergen cy flashe rs stop
tempor arily.
""
47

Lights and Vision
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph
(15 km/h) or turn t he ignition
off.
A WARNING
Curved mirror surfaces (for example convex)
enlarge the field of vision. However, they
make objects in the mirror appear smaller
and farther away. You may estimate incor­
rectly when you use these mirrors to gauge
your distance from the vehicles behind you
when changing lanes, which increases the risk of an accident.
«1j) Note
-Applies to vehicles with power folding exte­
rior mirrors: if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must use the pow­
er folding function to fold the mirror all the
way out. The mirrors will make a loud noise
when they latch into place. The mirror hous­
ing must not be moved back into place by
hand because this would impair the func­
tion of the mirror mechanism.
- Applies to vehicles without power folding
exterior mirrors : if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must move it back in place by hand.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Never fold power folding exterior mirrors*
by hand . Only fold them in and out using
the power controls.
(D Tips
-If the power adjusting function malfunc­
tions, the glass in both mirrors can be ad­
justed by pressing on the edge of it by hand.
- The exterior mirror settings are stored with
the memory
function*~ page 59.
so
Dimming the mirrors
Your vehicle is equipped with a manual or auto­
matic* dimming rearview mirror .
Manual dimming rearview mirror
.,. Pull the lever on the bottom of the mirror back.
Automatic dimming rearview mirror*
.,. The interior and exterior mirrors dim automati­
cally when light shines on them, for example
from headlights on a vehicle behind you.
A WARNING
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
can irritate the skin, eyes and respiratory sys­
tem. If there is contact with the fluid, flush immediately with plenty of water. Consult a
physician if necessary .
- Repeated or long-term exposure to electro­
lyte fluid can lead to irritation of the air­
ways, especially in people with asthma or other respiratory conditions. Take deep
breaths immediately after leaving the vehi­
cle or, if this is not possible, open all of the
doors and windows as wide as possible.
- If electrolyte fluid enters the eyes, flush
them thoroughly with a large amount of
clean water for at least 15 minutes and then
seek medical attention.
- If electrolyte fluid comes into contact with
the skin, flush the affected area with clean
water for at least 15 minutes and then clean
with soap and water and seek medical at­ tention. Clean affected clothing and shoes
thoroughly before wearing again.
- If the fluid was swallowed and the person is
conscious, flush the mouth with water for at
least 15 minutes . Do not induce vomiting
unless this is recommended by medical pro­
fessionals. Seek medical attention immedi­
ately .
@ Note
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
damages plastic surfaces and paint. Clean

Lights and Vision
@-Fast wiping
©-Single wipe. If you hold the lever in this posi­
tion longer, the wipers switch from slow wiping
to fast wiping .
®-Clean the windshield . The wipers wipe one
time after several seconds of driving to remove
water droplets . You can switch this function off
by moving the lever to position ® within
10 sec­
onds of the afterwipe. The afterwipe function is
r e activated the next time you switch the ignition
on.
Clean the headlights*. The headlight washer sys­
tem* operates only when the low beam head­
lights are on. If you move the lever into position
@, the headlights will be cleaned at fixed inter­
vals .
@-Wipe the rear window. The number of wipes
depends on the windshield wiper movement.
The rear wiper automatically switches on when
the reverse gear is selected and the front wind­
shield wipers are on and running.
(j) -Clean the rear window. The number of wipes
depends on how long the lever is held in position
(z). This may also clean the rearview camera, de­
pending on the vehicle equipment.
A WARNING
- The rain sensor is only intended to assist the
driver. The driver may still be responsible
for manually switching the wipers on based on visibility conditions.
- The windshield may not be treated with wa­ ter-repelling windshield coating agents . Un­
favorable conditions, such as wetness, dark­
ness or low sun, can result in increased
glare, which increases the risk of an acci­
dent. Wiper blade chatter is also possible.
- Properly functioning windshield wiper
blades are required for a clear view and safe
driving ~ page 53, Replacing wiper
blades .
«1j) Note
-If there is frost, make sure the windshield
wiper blades are not frozen to the wind-
52
shield. Switching on the windshield wipers
when the blades are frozen to the wind­ shield can damage the wiper blades.
- The windshield wiper system must be
switched off (lever in position 0) before us­
ing a car wash. This prevents the wipers
from switching on unintentionally and caus­ ing damage to the windshield wiper system.
(D Tips
- The windshield wipers switch off when the
ignition is switched off. You can activate the
windshield wipers after the ignition is
switched back on by moving the windshield
wiper lever to any position .
- Worn or dirty windshield wiper blades result
in streaking. This can affect the rain sensor
function . Check your windshield wiper
blades regularly.
- The washer fluid nozzles for the windshield
washer system are heated at low tempera­
tures when the ignition is on.
- When stopping temporarily, such as at a
traffic light, the speed of the windshield
wipers automatically reduces by one level.
Cleaning the wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner.
Windshield wiper
.,. Place the windshield wiper arms in the service
position
~ page 53.
.,. Fold the windshield wiper arms away from the
windshield.
Rear window wiper
.,. Fold the wiper arm away from the rear window.
A WARNING
Dirty windshield wiper blades can impair vi­
sion, which increases the risk of an accident.
-

u co ..... N r-­N .....
~ 0 co
Replacing wiper blades
Fig. 49 Remov ing w indshi el d w iper blades
Windshield wiper serv ice po sition /blade
replacement position
"' To bring the windshield wipers into the service
pos ition, turn the ignition off and move the
windshield wiper lever into position @
¢ page 51, fig. 47.
"'T o bring the windshield wipers back to the nor­
mal pos ition, switch the ignition on and hold
the windshie ld wiper lever in posit ion @ until
the windshie ld wipers go back to the normal
pos ition, or d rive faster than 8 mph (12 km/h) .
You can a lso tu rn the service position on or off in
the Infotainment system :
"'Switch the windshield wipers off (position @
¢page 51 , fig. 47) .
"'Select : the I MENU ! button> Vehicle> left con­
trol button >
Service & checks > Wiper change
position .
Removing the wiper blade
"'Fold the windshield wiper arm away from the
windshield .
"' Press the locking knob (D ¢ fig. 49 on the wiper
blade . Hold the wiper blade firmly .
"'Remove the wiper blade in the direct ion of the
arrow .
Installing the wiper blade
"'Insert the new wiper blade into the mount on
the wiper arm
@ until it clicks into place.
"'Place the wiper arm back on the windshield .
"'Turn the serv ice position off.
Lights and Vision
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice each
year .
(D Note
- Only fold the windshield wipers away when
they are in the service pos ition. Otherwise,
you risk damaging the paint on the hood or
the windshield wiper motor .
- You should not move your veh icle or operate
the windsh ield wiper lever when the wiper
arms are folded away from the windshield .
Th e windshield wipers would move back in­
to their or iginal pos ition and could damage
the hood and windshield.
- T o red uce the risk of damage to the wiper
system, always loosen blades wh ich are fro­
zen to the windshield before operating the
w ipers.
- To reduce the risk of damage to the wiper
blades, do not use gasoline, kerosene, paint
thinner, or other solvents on or near the
wiper blades.
- To reduce the risk of damage to the wiper
arms or other components, do not attempt
to move the wipers by hand.
(D Tips
- You can also use the service position, for ex­
ample, if you want to protect the windshield
from icing by using a cover .
- You cannot activate the service posit ion
when the hood is open .
Replacing rear wiper blade
Fig . SO Rear w indow wiper : installing the w ip er blade
53

Lights and Vision
Removing the wiper blade
• Fo ld the wiper arm away from the rear window .
• Remove the wiper blade from its holder.
Installing the wiper blade
• Press the wiper b lade mount into the retainer.
• Fo ld the window wipe r arm bac k onto the rear
window.
WARNING
F or safety reasons, the windshie ld wiper
blades sho uld be replaced once or twice each
year .
Digital compass
Switching the compass on and off
App lies to: ve hicles w ith digital compass
F ig . 51 Re arview m irror : dig it al co mpass is sw itc hed o n
54
• To turn the compass on or o ff, press the button
@ unti l the compass in the mi rror appears or
disappears.
The dig ita l compass o nly works when the ignit ion
i s turned on . T he directions a re indicated with ab­
breviations:
N (north), NE (northeast), E (east),
SE (so utheast), S (so uth), SW (southwest), W
(west), NW (northwest) .
(D Tips
To prevent inaccurate compass readings, do
not br ing any remote contro ls, electrical devi­
ces or metallic objects near the mirror.

u co ..... N r-­N .....
~ 0 co
Lights and Vision
Adjusting the magnetic zone
Applies to: ve hicles with d ig ital compass
The magnetic zone must be adjusted correctly for the compass to read accurately.
Fig . 52 Magnetic zone map
• Press and hold the button @ Q page 54, fig . 51
until the number of the selected magnetic zone
appears in the rearview mirror .
• Press the button@repeatedly to select the
correct magnetic zone . The selection mode
turns off after a few seconds.
Calibrating the compass
A ppl ies to: ve hicles w ith d ig ital compass
If the display is incorrect or inaccurate, the com­
pass must be recalibrated.
• Press and hold the button @ until a C appears
in the interior rearview mirror .
• Drive in a circle at about 6 mph (10 km/h) until
a direction is displayed in the interior rearview
mirror.
A WARNING
To reduce the risk to yourself and other driv­
ers, calibrate the compass in an area where
there is no traffic.
.
55