u co ..... N
range and you have released the accelerator ped
a l once .
I f t he engine speed lim itation was act ivated by
an eng ine contro l m alfu nction, the
II ind icator
light also turns on. Make su re the engine speed
does not go above the speed displayed, for exam
p le when downshifting. Drive to an autho rized
Aud i dealer or authorized Aud i Serv ice Facility im
mediately to have the malfunction corrected.
--... Engine oil sensor
II Oil l evel sy stem: malfunction! Pleas e con
tact Service
The sensor to check the engine oil level has
fa iled. Drive to an authorized Aud i dealer or au
thor ized Audi Service Fac ility immed iate ly to have
the malfunct ion co rrected.
• O il le vel sensor : o il change necessary. Please
c ontact Service
F ue l has entered the engine oi l as a resu lt of fre
q uent short dr ives. Avoid high engine speeds, full
acceleration and heavy engine loads. Dr ive to an
author ized Audi dealer or author ized Audi Service
Fac il ity immediately to have the oil changed .
• Oil pressure senso r: malfunction! Plea se
contact Service
There is a malfunction in the oil pressure sensor .
Drive to an authorized Audi dea ler or a uthorized
Aud i Service Facility immediately to have the
malfunct ion corrected.
f Engine warm-up request
0 Plea se driv e to warm up eng ine
F ue l has entered the eng ine oi l, either from low
outside temperatures o r frequent short drives.
Drive unt il the engine is warm so that the fue l in
the eng ine oi l wi ll evaporate. Avoid high engine
speeds, full accelerating and heavy eng ine loads
when doing this.
Bil Tank system
I"-
~ 1111 Pl ease r efu el 0 <( 0 00
Coc kpit o ver view
If the indicato r light turns on for the first time
and the message appears, there are about 2 .1
gallons (8 liters) of fuel left in the tank .
fiD Please refuel immediately
If the indicato r light turns on the message ap
pears, the fuel ta nk is a lmost empty. Refue l the
vehicle immedia tely.
1111 Tank system: malfunction! Plea se contact
Service
There is a ma lfunction in the fuel tank system.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected.
(D Tips
F o r more information on f ueli ng, see
r=;, page 311 .
~ Washer fluid level
m Please add washer fluid
Fill the was her fluid for the windshie ld washer
system and the headlight washer system* when
the ignit ion is switched
off ¢ page 323 .
$ vVindshield wipers: malfunction! Please con
tact Service
The re is a ma lfunction w ith the windshield wip
ers.
Drive to an authori zed A udi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected.
~ Driver's door
II D riv er 's door : malfunction! Shift to P befo re
lea ving veh icle. Se e owner's manual
There is a ma lfunction in the driver's door. Se lect
the "P" selector lever posit ion to secure the vehi-
c le.
~
27
u co ..... N r-N .....
~ 0 co
this liquid as quickly as possible, for example
with a wet sponge.
@ Tips
- If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
will not function correct ly,
- The automatic dimming mirrors do not dim
when the interior lighting is turned on or
the reverse gear is selected.
Sun visors
Fig. 45 Sun visor
Sun visor
The sun visors for the dr iver and front passenger
can be re leased from their mounts and turned
to
ward the doors ¢ fig. 45 (D.
They can also be moved back and forth length
wise in this posit ion.
Vanity mirror
The -mir ror lighting- switches on when the cover
over the vanity mirror 2* opens .
Sunshade
App lies to: ve hicles with s unsh ad e
Fig. 46 Rea r door : sunshade
Lights and Vision
Rear door sunshade
.,. Pull the sunshade out and attach it to the re
tainer on the upper door frame ¢ fig. 46.
Windshield wipers
Switching the wipers on
•®
• @
•@
@.
• @
•®
Fig. 47 Winds hield wiper leve r
(!)-
. ®
Fig. 48 Rear window wiper operat ion
Move the windshield wiper lever to the corre
sponding position:
@ -Windshield w ipers off
co 0 ~
;&
a,
0 ~
;&
(D -Rain sensor mode . T he windshield wipers
switch on once the veh icle speed exceeds approx
imately 2 mph (4 km/h) and it is raining. The
higher the sensitivity of the ra in sensor that is set
(switch ® to the right), the earlier the wind
shield wipers react to moisture on the wind
shield. You can deactivate the rain sensor mode
in the Infotainment system, which switches the
intermittent mode on . To do this, select:
I MENU I
button > Vehicle > left control button > Driver
as sistance > Rain sensor.
In interm ittent mode,
you can adjust the interval time using the switch
®·
@ -Slow w iping .,.
51
Lights and Vision
@-Fast wiping
©-Single wipe. If you hold the lever in this posi
tion longer, the wipers switch from slow wiping
to fast wiping .
®-Clean the windshield . The wipers wipe one
time after several seconds of driving to remove
water droplets . You can switch this function off
by moving the lever to position ® within
10 sec
onds of the afterwipe. The afterwipe function is
r e activated the next time you switch the ignition
on.
Clean the headlights*. The headlight washer sys
tem* operates only when the low beam head
lights are on. If you move the lever into position
@, the headlights will be cleaned at fixed inter
vals .
@-Wipe the rear window. The number of wipes
depends on the windshield wiper movement.
The rear wiper automatically switches on when
the reverse gear is selected and the front wind
shield wipers are on and running.
(j) -Clean the rear window. The number of wipes
depends on how long the lever is held in position
(z). This may also clean the rearview camera, de
pending on the vehicle equipment.
A WARNING
- The rain sensor is only intended to assist the
driver. The driver may still be responsible
for manually switching the wipers on based on visibility conditions.
- The windshield may not be treated with wa ter-repelling windshield coating agents . Un
favorable conditions, such as wetness, dark
ness or low sun, can result in increased
glare, which increases the risk of an acci
dent. Wiper blade chatter is also possible.
- Properly functioning windshield wiper
blades are required for a clear view and safe
driving ~ page 53, Replacing wiper
blades .
«1j) Note
-If there is frost, make sure the windshield
wiper blades are not frozen to the wind-
52
shield. Switching on the windshield wipers
when the blades are frozen to the wind shield can damage the wiper blades.
- The windshield wiper system must be
switched off (lever in position 0) before us
ing a car wash. This prevents the wipers
from switching on unintentionally and caus ing damage to the windshield wiper system.
(D Tips
- The windshield wipers switch off when the
ignition is switched off. You can activate the
windshield wipers after the ignition is
switched back on by moving the windshield
wiper lever to any position .
- Worn or dirty windshield wiper blades result
in streaking. This can affect the rain sensor
function . Check your windshield wiper
blades regularly.
- The washer fluid nozzles for the windshield
washer system are heated at low tempera
tures when the ignition is on.
- When stopping temporarily, such as at a
traffic light, the speed of the windshield
wipers automatically reduces by one level.
Cleaning the wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner.
Windshield wiper
.,. Place the windshield wiper arms in the service
position
~ page 53.
.,. Fold the windshield wiper arms away from the
windshield.
Rear window wiper
.,. Fold the wiper arm away from the rear window.
A WARNING
Dirty windshield wiper blades can impair vi
sion, which increases the risk of an accident.
-
u co ..... N r-N .....
~ 0 co
Replacing wiper blades
Fig. 49 Remov ing w indshi el d w iper blades
Windshield wiper serv ice po sition /blade
replacement position
"' To bring the windshield wipers into the service
pos ition, turn the ignition off and move the
windshield wiper lever into position @
¢ page 51, fig. 47.
"'T o bring the windshield wipers back to the nor
mal pos ition, switch the ignition on and hold
the windshie ld wiper lever in posit ion @ until
the windshie ld wipers go back to the normal
pos ition, or d rive faster than 8 mph (12 km/h) .
You can a lso tu rn the service position on or off in
the Infotainment system :
"'Switch the windshield wipers off (position @
¢page 51 , fig. 47) .
"'Select : the I MENU ! button> Vehicle> left con
trol button >
Service & checks > Wiper change
position .
Removing the wiper blade
"'Fold the windshield wiper arm away from the
windshield .
"' Press the locking knob (D ¢ fig. 49 on the wiper
blade . Hold the wiper blade firmly .
"'Remove the wiper blade in the direct ion of the
arrow .
Installing the wiper blade
"'Insert the new wiper blade into the mount on
the wiper arm
@ until it clicks into place.
"'Place the wiper arm back on the windshield .
"'Turn the serv ice position off.
Lights and Vision
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice each
year .
(D Note
- Only fold the windshield wipers away when
they are in the service pos ition. Otherwise,
you risk damaging the paint on the hood or
the windshield wiper motor .
- You should not move your veh icle or operate
the windsh ield wiper lever when the wiper
arms are folded away from the windshield .
Th e windshield wipers would move back in
to their or iginal pos ition and could damage
the hood and windshield.
- T o red uce the risk of damage to the wiper
system, always loosen blades wh ich are fro
zen to the windshield before operating the
w ipers.
- To reduce the risk of damage to the wiper
blades, do not use gasoline, kerosene, paint
thinner, or other solvents on or near the
wiper blades.
- To reduce the risk of damage to the wiper
arms or other components, do not attempt
to move the wipers by hand.
(D Tips
- You can also use the service position, for ex
ample, if you want to protect the windshield
from icing by using a cover .
- You cannot activate the service posit ion
when the hood is open .
Replacing rear wiper blade
Fig . SO Rear w indow wiper : installing the w ip er blade
53
u co ..... N r--N ..... 0 <( 0 00
Wear
Brake pad wear depends largely on the way the
vehicle is driven and on operating conditions.
This is especially true if you are driving frequently in the city and on curves or with a sporty driving
style.
Operating noise
Noises may occur when braking depending on the
speed, braking force and outside conditions such
as temperature and humidity.
Wet conditions or road salt
In certain situations, for example after driving
through water, in heavy rain or after washing
your car, the braking effect may be reduced due
to moisture or ice on the brake rotors and brake
pads. The brakes must be "dried" first with a few
careful brake applications.
At higher speeds and with the windshield wipers
turned on, the brake pads press against the brake
rotors for a short amount of time. This action,
which is not felt by the driver, happens at regular
intervals and ensures a better reaction time for
the brakes in wet weather.
The braking effect can also be reduced if you are
driving on salted roads and you do not apply the brakes for long periods of time. The layer of salt
on the brake rotors and pads must be worn off
first when the brakes are applied.
Corrosion
Leaving the vehicle parked for long periods of
time, low mileage and avoiding heavy braking
can contribute to corrosion on the brake rotors
and to dirty brake pads.
If you usually avoid heavy braking or if there is
corrosion present, occasional heavy braking at high speeds is recommended to clean the brake
rotors and
pads¢ ,&..
Brake system malfunction
If you notice that the brake pedal travel has sud
denly increased, then a brake circuit in the dual
circuit brake system may have malfunctioned. Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
Intelligent Technology
problem corrected. On the way there, drive with
reduced speed and keep in mind that you will
need a longer distance to stop and you will need
to press the brake pedal harder.
Low brake fluid level
When the brake fluid level is low, malfunctions in
the brake system may occur. The brake fluid level
is electronically monitored.
Brake booster
The brake booster amplifies the pressure you ap
ply to the brake pedal.
& WARNING
= -
- Only apply the brakes for the purpose of
cleaning the brake system when road and
traffic conditions permit. You must not en
danger other road users. This increases the
risk of an accident.
- Never let the vehicle roll while the engine is
stopped because this increases the risk of an
accident.
- Never place objects in the driver's footwell.
An object could end up in the area around
the pedals and prevent you from using
them. You would not be able to use the ped
als if sudden driving or braking maneuvers
were needed, which increases the risk of an
accident.
- Only use floor mats that do not obstruct the
area around the pedals and that can be se
curely fastened in the footwells.
- To reduce the risk of injury, do not place
your foot under the brake pedal.
@ Note
- Never let the brakes "rub" by pressing the
pedal lightly when braking is not actually
necessary. This causes the brakes to over
heat and increases braking distance and
causes wear.
- Before driving downhill a long distance on a
steep hill, decrease your speed and select a
lower gear. This makes use of the engine
braking effect and relieves the brakes. If
you need to brake additionally, brake in in- tervals and not continuously.
.,,.
143
Fuses and bulb s
Fuse panel@ (brown ) Fuse panel© (blac k)
N o. E quip ment No. Equipmen t
2
Mass airflow sensor, camshaft adjust-
ment, charge air cooler pump 1 Fr ont seat heating
2 Windshie ld wipers
3 Exhaust doors, fuel injectors, radiator inlet 3 Left head light elect ronics
4 Vacuum pump , hot water p ump, particu-
late sensor, biodiesel sensor 4 Panorama glass roof
s L eft front doo r contro l modu le
5 Brake light sensor 6 Sockets
6 Engine valves, camshaft adjustment 7 Right rear door cont rol mod ule
7
Heated oxygen sensor, mass airflow sen-8 All wheel drive
sor
8
Water pump, high pressure pump, high
pressure regulator va lve
9 Hot water pump
9 R ight headlight electronics
10
Windshield washer system/headlight
washer system
1 1 Left rear door contro l module
10
Oil pressure sensor, oil temperature sen-
sor
Fu se p anel @ (blac k)
11 Clutch pedal position sensor No. Equipment
12 Engine valves
Seat ventilation, rearv iew mirror, cl imate
13 Radiator fan 1 control system, rear cl imate control sys-
14 Fuel injectors tern controls
, windsh ie ld defogger
15 Ignition coils 2 Gateway, climate control system
16 Fuel pump 3 Sound act uator/exhaust sound tuning
Fuse panel @ (red )
4 Clutch pedal posit ion sensor
5 Engine start
N o. Equipment 7 Rear USB charging port
1 Anti-theft a larm system 8 Homelink
2 Engine control module 9 Adaptive cruise control
3 Lumbar support 11 Video camera
4 Automatic transm ission selector mecha-
nism 12 Matrix LED headlight/right LED headlight
5 Horn
13 Matrix LED headlight/ left LED headlight
6 Electromechan ica l park ing brake
14 Rear window wiper
7 Gateway control module Fu se panel © (red )
8 Interior headliner lights No . Equipmen t
10 Airbag control module 1 Ignition coils
11 Electronic Stabilization Control (ESC) 5 E ng ine mount
12 Diagnostic connector, light/rain sensor 6 Automatic transmiss ion
13 Climate control system 7 I nstrument panel
1 4 Right front door control module 8 C limate control system (blower)
lS A/C compressor
10 Dynamic stee ring
11 Eng ine start
36 0
Index
What happens if you wear your safety belt too
loose? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
265
What happens to unbelted occupants? . . . . 262
What impairs driving safety? . . . . . . . . . . . . 252
Wheel bo lts . . . . . . . . . . . . . . . . . . . . . . . . . 340
Wheel replacement . . . . . . . . . . . . . . . . . . 352
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Clean ing . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Glossary of tire and loading terminology . 328
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . 352
Tire pressure monitoring system . . . . . . . 342
Tires and vehicle load limits ....... .... 337
Wheel wrench . . . . . . . . . . . . . . . . . . . . . . . . 350
When must a safety belt be replaced? . . . . 263
When must the airbag system be inspected? 281
Where are lower anchorages located?
306
Wi-Fi
Audi music stream . . . . . . . . . . . . . . . . . . .
229
Audio player . . . . . . . . . . . . . . . . . . . . . . . . 229
Online media . . . . . . . . . . . . . . . . . . . . . . . 230
also refer to W i-F i . . . . . . . . . . . . . . . . . . . 229
Windows
Child safety lock . . . . . . . . . . . . . . . . . . . . . .
40
Cleaning/removing ice . . . . . . . . . . . . . . . . 346
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . .
71
Power windows . . . . . . . . . . . . . . . . . . . . . . 40
Windshield
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . 71
also refer to Windshield . . . . . . . . . . . . . . . 51
Windshield washer system ......... . 51, 323
Reservoir capacity . . . . . . . . . . . . . . . . . . . 369
W indshield wipers . . . . . . . . . . . . . . . . . . . . . 51
W inter operation
Car washes . . . . . . . . . . . . . . . . . . . . . . . . .
344
Cooling system .. ................ ... . 319
Defrosting the windows . . . . . . . . . . . . . . . 7 1
Removing ice from windows . . . . . . . . . . . 346
Seat heating . . . . . . . . . . . . . . . . . . . . . . . . . 71
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . 340
Steering whee l heating . . . . . . . . . . . . . . . . 72
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Vehicle battery . . . . . . . . . . . . . . . . . . . . . . 322
Windshield washer system . . . . . . . . . . . . 323
Winter tires . . . . . . . . . . . . . . . . . . . . . . . . . . 340
388
X
Xenon headlights . . . . . . . . . . . . . . . . . . . . . 362
z
Zooming on the map
Mult ifunct ion steer ing whee l . . . . . . . . . . .
13
Zoom (map) ...... .. .. ........... 205,213