2017 YAMAHA MT09 TRACER Owners Manual

Instrument and control functions
3-10
1
234
5
6
7
8
9
10
11
12
Information display
There are 3 information displays. Push
the select switch “ / ” to change the
selected information display.
The following items are shown in the in-
formation displays:

odometer

two tripmeters

fuel reserve tripmeter

elapsed time

air temperature

coolant temperature

average fuel consumption

instantaneous fuel consumption
TIPYou can select which items are shown
in each information display. See Set-ting mode on page 3-12.
Odometer and tripmeters
The odometer shows the total distance
traveled by the vehicle.
The tripmeters “TRIP-1” and “TRIP-2”
show the distance traveled since they
were last set.
To reset a tripmeter, use the select
switch to display the tripmeter you want
to reset. Then push the “RESET” but-
ton briefly so that the tripmeter flashes, and then push the “RESET” button
again for two seconds.
TIP
The odometer will lock at 999999.

The tripmeters will reset and con-
tinue counting after 9999.9 isreached.
Fuel reserve tripmeter
When approximately 2.6 L (0.69 US gal,
0.57 Imp.gal) of fuel remains in the fuel
tank, the last segment of the fuel meter
starts flashing. The display will change
to the fuel reserve tripmeter mode
“TRIP-F” and start counting the dis-
tance traveled from that point.
In this case, push the select switch to
switch the display in the following order:
1. Information display
2. Display–1
3. Display–2
4. Display–3
GEARN
5.0
TRIP-1 km
7.0
TRIP-2km
km
20
ODO
GEARN
20
ODO km
12.3
FUEL AVG km/L
km/L
12.3
CRNT FUEL
GEARN
25
A.TEMP ˚C
Lo
C.TEMP˚C
0:06
TIME TRIP
3
4
2
1
20
ODOkm
5.0
TRIP-1km
7.0
TRIP-2km
GEAR4
3.4
TRIP-Fkm
2PP-9-E3.book 10 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-11
1
23
4
5
6
7
8
9
10
11
12 TRIP-F
 Display–1  Display–2 
Display–3  TRIP-F
After refueling, you can manually reset
the fuel reserve tripmeter immediately,
or allow it to reset automatically after
traveling 5 km (3 mi). When the fuel re-
serve tripmeter is reset, it will disappear
from the display.
Elapsed time
This timer shows the time that has
elapsed since the key was turned to
“ON”. The timer automatically resets
when the key is turned to “OFF”.
TIPThere are also “TIME–2” and “TIME–3”
elapsed time displays, but they cannot
be set to the information display. See
Setting mode on page 3-12 for more in-
formation.
Air temperature
This shows the air temperature from –9
 C to 93 C in 1  C increments. The
temperature displayed may vary from
the ambient temperature.TIP
–9 C will be displayed even if the
ambient temperature falls below
–9 C.

The accuracy of the temperature
reading may be affected when rid-
ing slowly (under 20 km/h [13
mi/h]) or when stopped at trafficsignals, railroad crossings, etc.
Coolant temperature
This shows the temperature of the cool- ant. The coolant temperature varies
with changes in the weather and en-
gine load.
If the message “Hi” flashes, stop the ve-
hicle then stop the engine and let it
cool. (See page 6-40.)
TIPThe selected information display can-
not be switched while the message “Hi”is flashing.NOTICE
ECA10022
Do not continue to operate the en-gine if it is overheating.
0:06
TIME TRIP
25
A.TEMP
˚C
Lo
C.TEMP˚C
GEAR4
Hi
C.TEMP ˚C
2PP-9-E3.book 11 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-12
1
234
5
6
7
8
9
10
11
12
Average fuel consumption
This function calculates the average
fuel consumption (fuel economy) of the
vehicle since it was last reset. The av-
erage fuel consumption display can be
set to “km/L” or “L/100km”; or when
miles is selected “MPG” will be dis-
played.

The “km/L” display shows the av-
erage distance that can be trav-
eled on 1.0 L of fuel.

The “L/100km” display shows the
average amount of fuel necessary
to travel 100 km.

The “MPG” display shows the av-
erage distance that can be trav-
eled on 1.0 Imp.gal of fuel.
To reset the average fuel consumption
display, use the select switch to select
the information display that contains
the average fuel consumption display.
Push the “RESET” button briefly so that
the average fuel consumption display
flashes, and then push the “RESET”
button again for 2 seconds while the display is flashing.
TIPAfter resetting the average fuel con-
sumption display, “_ _._” will be shown
until the vehicle has traveled 1 km (0.6mi).NOTICE
ECA15474
If there is a malfunction, “– –.–” will
be continuously displayed. Have aYamaha dealer check the vehicle.
Instantaneous fuel consumption
This function calculates the instanta-
neous fuel consumption (fuel economy)
under current riding conditions. The in-
stantaneous fuel consumption display
can be set to “km/L” or “L/100km”; or
when miles is selected “MPG” will be
displayed.
The “km/L” display shows the dis-
tance that can be traveled on 1.0 L
of fuel.

The “L/100km” display shows the
amount of fuel necessary to travel
100 km.

The “MPG” display shows the dis-
tance that can be traveled on 1.0
Imp.gal of fuel.
TIPIf traveling at speeds under 10 km/h(6.0 mi/h), “_ _._” will be displayed.NOTICE
ECA15474
If there is a malfunction, “– –.–” will
be continuously displayed. Have aYamaha dealer check the vehicle.
Setting mode
12.3
FUEL AVG km/L
12.3
CRNT FUEL km/L
1. Setting mode display
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
1
2PP-9-E3.book 12 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-13
1
23
4
5
6
7
8
9
10
11
12 This mode allows you to set, select, or
reset the items shown in the informa-
tion display.
TIP
The transmission must be in neu-
tral and the vehicle must be
stopped to change settings in this
mode.

Shifting the transmission into gear
or turning the key to “OFF” will exit
the setting mode and all changeswill be saved.
Push and hold the menu switch
“MENU” for 2 seconds to enter the set-
ting mode. To exit the setting mode and
return to the normal display, push and
hold the menu switch again for 2 sec-
onds. Resetting the maintenance counters
1. Use the select switch to highlight
“Maintenance”.
2. Push the menu switch, and then push the “RESET” button to select
the item to reset.
3. While the selected item is flashing, push the “RESET” button for 2
seconds.
Display Description
This function allows you to
check and reset the “OIL”
oil change interval
(distance traveled), and
the “FREE-1” and
“FREE-2” maintenance
intervals.Maintenance
This function allows you to
check and reset the
“TIME–2” and “TIME–3”
functions. These time trips
show the total elapsed
time that the key has been
in the “ON” position. When
the key is turned to “OFF”,
the time trips stop counting
but are not reset. The
maximum time that can be
shown is 99:59.
When the time trips reach
100 hours, they
automatically reset to 0:00
and continue counting.
This function allows you to
switch the display units
between kilometers and
miles. When kilometers are
selected, the fuel
consumption units can be
switched between
“L/100km” and “km/L”.
This function allows you to
change the items shown in
3 information displays.
This function allows you to
adjust the brightness of the
multi-function meter unit
panel.
This function allows you to
set the clock.
This function allows you to
reset all items, except the
odometer and the clock.
Time TripUnitDisplayBrightnessCloc
k
All Reset
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
20
OIL km
10
FREE-1 km
10
FREE-2kmMaintenance
2PP-9-E3.book 13 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-14
1
234
5
6
7
8
9
10
11
12
4. Push the menu switch to return to
the setting mode menu.
Checking and resetting “TIME
–2” and
“TIME
–3”
1. Use the select switch to highlight “Time Trip”.
2. Push the menu switch to display “TIME–2” and “TIME–3”. To reset
a time trip, push the “RESET” but-
ton to select the item to reset. 3. While the selected item is flashing,
push the “RESET” button for 2
seconds.
4. Push the menu switch to return to the setting mode menu.
Selecting the units
1. Use the select switch to highlight “Unit”. 2. Push the menu switch. The unit
setting display will be shown.
TIP
When kilometers are already se-
lected, “km/L or L/100km” will flash
in the display.

When miles are already selected,
“km or mile” will flash in the dis-play.
TIP
Keep kilometers selected: Skip to
step 5.

Select miles or kilometers: Contin-ue with step 3.
3. Push the menu switch, then use the select switch to toggle between
“km” or “mile”, and then push the
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
TIME-2
0:07
TIME-3
0:07
Time TripMENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
Unitkm or mile
km
km/L or L/100km
km/L
2PP-9-E3.book 14 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-15
1
23
4
5
6
7
8
9
10
11
12 menu switch to confirm the selec-
tion.
TIP
When kilometers are selected,
“L/100km” or “km/L” can be set as
the fuel consumption display units.
Continue with step 4.

When miles are selected, the fuel
consumption display units will beset to “MPG”. Skip to step 6.
4. Use the select switch to move from “km or mile” to “km/L or L/100km”.
5. Push the menu switch, then use the select switch to toggle between
“km/L” and “L/100km”, and then
push the menu switch to confirm
the selection.
6. Use the select switch to highlight “ ”, and then push the menu
switch to return to the setting mode
menu.
Selecting the display items
1. Use the select switch to highlight “Display”.
2. Push the menu switch, then use the select switch to highlight the
display to change, and then push the menu switch again.
3. Use the select switch to highlight the item to change, and then push
the menu switch.
4. Use the select switch to select the item you want to display, and then
push the menu switch.
Unitkm or mile
km
km/L or L/100km
km/L
Unitkm or mile
km
km/L or L/100km
km/L
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
Display
Display-1Display-2Display-3
Display-11-1
A.TEMP
1-2
C.TEMP
1-3
TIME TRIP
2PP-9-E3.book 15 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-16
1
234
5
6
7
8
9
10
11
12
5. When you are finished changing
the settings, use the select switch
to highlight “ ”, and then push the
menu switch to return to the previ-
ous display.
6. Use the select switch to highlight “ ”, and then push the menu
switch to return to the setting mode
menu. Adjusting the meter panel brightness
1. Use the select switch to highlight
“Brightness”.
2. Push the menu switch.
3. Use the select switch to select the desired brightness level, and then
push the menu switch to return to
the setting mode menu. Setting the clock
1. Use the select switch to highlight
“Clock”.
2. Push the menu switch.
3. When the hour digits start flashing, use the select switch to set the
hours.
Display-11-1
ODO
1-2
C.TEMP
1-3
TIME TRIP
Display-11-1
ODO
1-2
C.TEMP
1-3
TIME TRIP
Display
Display-1Display-2Display-3
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
BrightnessMENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
2PP-9-E3.book 16 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-17
1
23
4
5
6
7
8
9
10
11
12 4. Push the menu switch and the
minute digits start flashing.
5. Use the select switch to set the minutes.
6. Push the menu switch to return to the setting mode menu.
Resetting all of the display items
1. Use the select switch to highlight “All Reset”. 2. Push the menu switch.
3. Use the select switch to highlight
“YES”, and then push the menu
switch.
TIPThe odometer and the clock cannot bereset.
EAU47634
D-mode (drive mode)D-mode is an electronically controlled
engine performance system with three
mode selections (“STD”, “A”, and “B”).
Push the drive mode switch “MODE” to
switch between modes. (See page
3-19 for an explanation of the drive
mode switch.)TIPBefore using D-mode, make sure you
understand its operation along with theoperation of the drive mode switch.
Mode “STD”
Mode “STD” is suitable for various rid-
ing conditions.
Clock
5
55
AM
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
All Reset
YESNO
1. Drive mode switch “MODE”
1
2PP-9-E3.book 17 ページ ２０１６年９月１３日　火曜日　午前９時７分