2017 YAMAHA MT09 TRACER set clock

Instrument and control functions
3-6
1
234
5
6
7
8
9
10
11
12
initially when the key is turned to “ON”,
if the indicator light remains on, or if the
indicator light flashes in a pattern (if a
problem is detected in the immobilizer
system, the immobili
zer system indica-
tor light will flash in a pattern), have a
Yamaha dealer check the vehicle.
TIPIf the immobilizer system indicator light
flashes in the pattern, slowly 5 times
then quickly 2 times, this could be
caused by transponder interference. Ifthis occurs, try the following.
1. Make sure there are no other im- mobilizer keys close to the main
switch. Other immobilizer system
keys may cause signal interfer-
ence and prevent the engine from
starting.
2. Use the code re-registering key to start the engine.
3. If the engine starts, turn it off, and try starting the engine with the
standard keys.
4. If one or both of the standard keys do not start the engine, take the
vehicle and all 3 keys to a Yamaha
dealer to have the standard keys re-registered.
EAU76322
Multi-function meter unitThe multi-function meter unit is
equipped with the following:
speedometer

tachometer

clock
1. “RESET” button
2. “TCS” button
3. Clock
4. Tachometer
5. Speedometer
6. Transmission gear display
7. Information display selection function
8. Information display
9. Fuel meter
10.Eco indicator “ECO”
11.Drive mode display
12.TCS display
GEARN
25
A.TEMP
°C
Lo
C.TEMP°C
0:00
TIME TRIP
89
10
11
12
12 3 4 56
7
2PP-9-E3.book 6 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-8
1
234
5
6
7
8
9
10
11
12
High-rpm zone: 11250 r/min and
above
Clock
The clock displays time in 12-hour for-
mat. To set the clock, see page 3-12.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear from
“F” (full) towards “E” (empty) as the fuel
level decreases. When the last seg-
ment of the fuel meter starts flashing,
refuel as soon as possible.
TIP
When the key is first turned to
“ON”, all of the display segments
of the fuel meter will appear for a
few seconds before the fuel meter
shows the actual fuel level.

If a problem is detected in the fuel
meter electrical circuit, the fuel me-
ter will flash repeatedly. If this oc-curs, have a Yamaha dealer check
the vehicle.
Eco indicator
The eco indicator comes on when the
vehicle is being operated in an environ-
mentally friendly, fuel-efficient manner.
The indicator goes off when the vehicle
is stopped.
TIPConsider the following tips to reduce
fuel consumption:
Avoid high engine speeds during
acceleration.

Travel at a constant speed.

Select the transmission gear that
1. Clock
1
1. Fuel meter
1
1. Eco indicator “ECO”
1
2PP-9-E3.book 8 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-12
1
234
5
6
7
8
9
10
11
12
Average fuel consumption
This function calculates the average
fuel consumption (fuel economy) of the
vehicle since it was last reset. The av-
erage fuel consumption display can be
set to “km/L” or “L/100km”; or when
miles is selected “MPG” will be dis-
played.

The “km/L” display shows the av-
erage distance that can be trav-
eled on 1.0 L of fuel.

The “L/100km” display shows the
average amount of fuel necessary
to travel 100 km.

The “MPG” display shows the av-
erage distance that can be trav-
eled on 1.0 Imp.gal of fuel.
To reset the average fuel consumption
display, use the select switch to select
the information display that contains
the average fuel consumption display.
Push the “RESET” button briefly so that
the average fuel consumption display
flashes, and then push the “RESET”
button again for 2 seconds while the display is flashing.
TIPAfter resetting the average fuel con-
sumption display, “_ _._” will be shown
until the vehicle has traveled 1 km (0.6mi).NOTICE
ECA15474
If there is a malfunction, “– –.–” will
be continuously displayed. Have aYamaha dealer check the vehicle.
Instantaneous fuel consumption
This function calculates the instanta-
neous fuel consumption (fuel economy)
under current riding conditions. The in-
stantaneous fuel consumption display
can be set to “km/L” or “L/100km”; or
when miles is selected “MPG” will be
displayed.
The “km/L” display shows the dis-
tance that can be traveled on 1.0 L
of fuel.

The “L/100km” display shows the
amount of fuel necessary to travel
100 km.

The “MPG” display shows the dis-
tance that can be traveled on 1.0
Imp.gal of fuel.
TIPIf traveling at speeds under 10 km/h(6.0 mi/h), “_ _._” will be displayed.NOTICE
ECA15474
If there is a malfunction, “– –.–” will
be continuously displayed. Have aYamaha dealer check the vehicle.
Setting mode
12.3
FUEL AVG km/L
12.3
CRNT FUEL km/L
1. Setting mode display
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
1
2PP-9-E3.book 12 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-13
1
23
4
5
6
7
8
9
10
11
12 This mode allows you to set, select, or
reset the items shown in the informa-
tion display.
TIP
The transmission must be in neu-
tral and the vehicle must be
stopped to change settings in this
mode.

Shifting the transmission into gear
or turning the key to “OFF” will exit
the setting mode and all changeswill be saved.
Push and hold the menu switch
“MENU” for 2 seconds to enter the set-
ting mode. To exit the setting mode and
return to the normal display, push and
hold the menu switch again for 2 sec-
onds. Resetting the maintenance counters
1. Use the select switch to highlight
“Maintenance”.
2. Push the menu switch, and then push the “RESET” button to select
the item to reset.
3. While the selected item is flashing, push the “RESET” button for 2
seconds.
Display Description
This function allows you to
check and reset the “OIL”
oil change interval
(distance traveled), and
the “FREE-1” and
“FREE-2” maintenance
intervals.Maintenance
This function allows you to
check and reset the
“TIME–2” and “TIME–3”
functions. These time trips
show the total elapsed
time that the key has been
in the “ON” position. When
the key is turned to “OFF”,
the time trips stop counting
but are not reset. The
maximum time that can be
shown is 99:59.
When the time trips reach
100 hours, they
automatically reset to 0:00
and continue counting.
This function allows you to
switch the display units
between kilometers and
miles. When kilometers are
selected, the fuel
consumption units can be
switched between
“L/100km” and “km/L”.
This function allows you to
change the items shown in
3 information displays.
This function allows you to
adjust the brightness of the
multi-function meter unit
panel.
This function allows you to
set the clock.
This function allows you to
reset all items, except the
odometer and the clock.
Time TripUnitDisplayBrightnessCloc
k
All Reset
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
20
OIL km
10
FREE-1 km
10
FREE-2kmMaintenance
2PP-9-E3.book 13 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-14
1
234
5
6
7
8
9
10
11
12
4. Push the menu switch to return to
the setting mode menu.
Checking and resetting “TIME
–2” and
“TIME
–3”
1. Use the select switch to highlight “Time Trip”.
2. Push the menu switch to display “TIME–2” and “TIME–3”. To reset
a time trip, push the “RESET” but-
ton to select the item to reset. 3. While the selected item is flashing,
push the “RESET” button for 2
seconds.
4. Push the menu switch to return to the setting mode menu.
Selecting the units
1. Use the select switch to highlight “Unit”. 2. Push the menu switch. The unit
setting display will be shown.
TIP
When kilometers are already se-
lected, “km/L or L/100km” will flash
in the display.

When miles are already selected,
“km or mile” will flash in the dis-play.
TIP
Keep kilometers selected: Skip to
step 5.

Select miles or kilometers: Contin-ue with step 3.
3. Push the menu switch, then use the select switch to toggle between
“km” or “mile”, and then push the
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
TIME-2
0:07
TIME-3
0:07
Time TripMENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
Unitkm or mile
km
km/L or L/100km
km/L
2PP-9-E3.book 14 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-15
1
23
4
5
6
7
8
9
10
11
12 menu switch to confirm the selec-
tion.
TIP
When kilometers are selected,
“L/100km” or “km/L” can be set as
the fuel consumption display units.
Continue with step 4.

When miles are selected, the fuel
consumption display units will beset to “MPG”. Skip to step 6.
4. Use the select switch to move from “km or mile” to “km/L or L/100km”.
5. Push the menu switch, then use the select switch to toggle between
“km/L” and “L/100km”, and then
push the menu switch to confirm
the selection.
6. Use the select switch to highlight “ ”, and then push the menu
switch to return to the setting mode
menu.
Selecting the display items
1. Use the select switch to highlight “Display”.
2. Push the menu switch, then use the select switch to highlight the
display to change, and then push the menu switch again.
3. Use the select switch to highlight the item to change, and then push
the menu switch.
4. Use the select switch to select the item you want to display, and then
push the menu switch.
Unitkm or mile
km
km/L or L/100km
km/L
Unitkm or mile
km
km/L or L/100km
km/L
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
Display
Display-1Display-2Display-3
Display-11-1
A.TEMP
1-2
C.TEMP
1-3
TIME TRIP
2PP-9-E3.book 15 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-16
1
234
5
6
7
8
9
10
11
12
5. When you are finished changing
the settings, use the select switch
to highlight “ ”, and then push the
menu switch to return to the previ-
ous display.
6. Use the select switch to highlight “ ”, and then push the menu
switch to return to the setting mode
menu. Adjusting the meter panel brightness
1. Use the select switch to highlight
“Brightness”.
2. Push the menu switch.
3. Use the select switch to select the desired brightness level, and then
push the menu switch to return to
the setting mode menu. Setting the clock
1. Use the select switch to highlight
“Clock”.
2. Push the menu switch.
3. When the hour digits start flashing, use the select switch to set the
hours.
Display-11-1
ODO
1-2
C.TEMP
1-3
TIME TRIP
Display-11-1
ODO
1-2
C.TEMP
1-3
TIME TRIP
Display
Display-1Display-2Display-3
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
BrightnessMENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
2PP-9-E3.book 16 ページ ２０１６年９月１３日　火曜日　午前９時７分

Instrument and control functions
3-17
1
23
4
5
6
7
8
9
10
11
12 4. Push the menu switch and the
minute digits start flashing.
5. Use the select switch to set the minutes.
6. Push the menu switch to return to the setting mode menu.
Resetting all of the display items
1. Use the select switch to highlight “All Reset”. 2. Push the menu switch.
3. Use the select switch to highlight
“YES”, and then push the menu
switch.
TIPThe odometer and the clock cannot bereset.
EAU47634
D-mode (drive mode)D-mode is an electronically controlled
engine performance system with three
mode selections (“STD”, “A”, and “B”).
Push the drive mode switch “MODE” to
switch between modes. (See page
3-19 for an explanation of the drive
mode switch.)TIPBefore using D-mode, make sure you
understand its operation along with theoperation of the drive mode switch.
Mode “STD”
Mode “STD” is suitable for various rid-
ing conditions.
Clock
5
55
AM
MENUMaintenanceTime TripUnitDisplayBrightnessClockAll Reset
All Reset
YESNO
1. Drive mode switch “MODE”
1
2PP-9-E3.book 17 ページ ２０１６年９月１３日　火曜日　午前９時７分