2017 Peugeot 208 Owner's Manual

3
Increase volume.
Decrease volume.
Mute on: cut the sound by
simultaneously pressing the volume
up and down buttons.
Mute off: press one of the two
volume buttons.Radio
Presetting a station
Press SRC/TEL repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
corresponding preset station.
Managing a list
Press LIST to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
.
Audio system / Bluetooth®

4
Select "Radio ".
Select "Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
RDS
RDS, if activated, allows you to
continue listening to the same station
by automatically retuning to alternative
frequencies. However, in certain conditions,
coverage of an RDS station may not be
assured throughout the entire country as
radio stations do not cover 100% of the
territory. This explains the loss of reception
of a station that can occur during a journey.
With source FM1 or FM2, press
MENU .
Select "Radio ".
Select or deselect "RDS " to switch
RDS on or off.
Confirm with " OK" to save the
setting.
Receiving TA messages
The TA (Traffic Announcement) function
gives priority to TA alert messages.
To operate, this function needs good
reception of a radio station transmitting
this type of message. When a traffic
report is transmitted, the current audio
source (radio, CD, USB, etc.) is interrupted
automatically to play the TA message.
Normal playback resumes at the end of
the transmission of the message. Press MENU
.
Select "Radio ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Confirm with " OK" to save the
setting.
Displaying RADIO TEXT
Radio Text is information transmitted by
the radio station related to the current
programme or song.
With the radio displayed on the
screen, press MENU .
Select " Radio".
Audio system / Bluetooth®

5
Select or deselect "TXT" to activate
or deactivate the display of Radio
Te x t .
Confirm with " OK" to save the
setting.Media
USB player
This unit comprises a USB port and a jack
socket, depending on model.
The system builds playlists (in temporary
memory), an operation which can take
from a few seconds to several minutes at
the first connection.
Limiting the number of non-music files and
the number of folders reduces this waiting
time. The playlists are updated every
time the ignition is switched off or a USB
memory stick is connected.
The lists are memorised: if they are not
modified, the subsequent loading time will
b e s h o r t e r. At the first connection, the order
suggested is by folder. When connecting
again, the previously chosen order is
retained.
Insert the USB memory stick into the USB port
or connect the USB device to the USB port
using a suitable cable (not supplied). Press SRC/TEL repeatedly to select
" USB ".
Press one of these buttons to select
the previous or next track in the list.
Press one of these buttons to select
the previous or next folder according
to the category chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Press LIST to display the structure
of the folders in the compilation.
.
Audio system / Bluetooth®

6
Select a line in the list.
Confirm with "OK".
Up a level in the menu.
Press MENU .
Select "Media ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Select the play mode: " Normal",
" Random ", "Random all" or
" Repeat ".Auxiliary socket (AUX)
Connect the portable device (MP3 player, etc.)
to the jack socket using an audio cable (not
supplied).
Press SRC/TEL repeatedly to select
" AUX ".
First adjust the volume of your portable device
(to a high level). Then adjust the volume of your
audio system. The controls are operated from
the portable device.
Do not connect a device to both the jack
socket and the USB port at the same time.
CD player
Insert a CD in the player; play begins
automatically.
Insert an MP3 compilation in the CD player.
The audio system searches for all of the music
tracks, which may take anything between a few
seconds and several tens of seconds, before
play begins. Press the SRC/TEL button
repeatedly to select " CD".
Press one of these buttons to go to
the previous / next track in the list.
Press one of these buttons to select
the previous or next folder in the
order chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Press LIST to display the folder
structure of the compilation.
Audio system / Bluetooth®

7
Select a line in the list.
Confirm with "OK".
Return to the top level of the folder structure to
select the type of tracks.
-

By Folders (CD or USB): all folders
containing audio files recognised on the
peripheral device, in alphabetical order
without following the folder structure.
-

By Artist (USB only): all of the artist names
defined in the ID3 Tags, in alphabetical
o r d e r.
-

By Genre (USB only): all of the genres
defined in the ID3 Tags.
-

By Playlist (CD or USB): if playlists have
been saved.
Information and advice
The audio system will only play files with
".mp3", ".wma" and ".wav" extensions on a CD
and can play files with ".ogg" extension only on
USB. To avoid any playback or display issues, it is
advisable to create file names that have less
than 20 characters and without using any
special characters (e.g. «?.; ù).
In order to be able to play a recorded CDR or
CDRW, it is preferable to select the ISO 9660
level 1, 2 or Joliet standard when recording the
CD.
If the disc is burned in another format, it may
not be played correctly.
It is recommended that the same recording
standard is always used for a given disc, with
as low a speed as possible (4x maximum) for
optimum sound quality.
In the particular case of a multi-session CD, the
Joliet standard is recommended.
The playlists accepted on CD, MP3, iPod and
USB connection are types ".m3u" and ".wpl".
The system can recognise up to 5,000 files in
500 folders on 8 levels.
On a single disc, the CD player can read up
to 255 MP3 files spread over 8 folder levels
with a maximum of 192 folders. However, it
is recommended that the number of levels is
limited to 2 so as to reduce the time taken to
access and play the CD.
The folder structure is not obser ved during
playback.Do not connect a hard disk or USB device other
than audio players to the USB port. This may
cause damage to your installation.
Use only USB memory sticks formatted FAT32
(File Allocation Table).
It is recommended that you use genuine
Apple
® USB cables for correct operation.
Bluetooth® audio streaming
Streaming allows music files on the telephone
to be played through the vehicle's speakers.
Connect the telephone: see the " Telephone"
section.
In the " Bluetooth: Audio " menu, select the
telephone to be connected.
The audio system connects to a newly paired
telephone automatically.
.
Audio system / Bluetooth®

8
Activate the streaming source by
pressing the S R C / T E L* button.
The control of common tracks is possible
via the audio system control buttons and the
steering mounted controls**. The contextual
information can be displayed in the screen.
The audio quality depends on the quality of the
transmission from the telephone.
Connecting Apple® players
Connect the Apple® player to the USB port
using a suitable cable (not supplied).
Play starts automatically. Management of the device is via the audio
system controls.
The classifications available are those of the
portable device connected (artists / albums /
genres / playlists / audio books / podcasts).
The version of software in the audio system
may not be compatible with the generation of
your Apple
® p l aye r.
*

I

n certain cases, play of the audio files must
be initiated from the keypad.
**

I

f the telephone supports the function.
Telephone
Pairing a Bluetooth®
telephone
As a safety measure and because it
requires sustained attention by the
driver, the pairing of a Bluetooth mobile
telephone with the Bluetooth hands-free
system of your audio system must be done
with the vehicle stationary and the ignition
on.
Visit www.peugeot.co.uk for more information
(compatibility, more help, etc.).
Activate the telephone's Bluetooth function and
ensure that it is set as visible to all (refer to the
telephone user guide). Press the MENU button.
Audio system / Bluetooth®

9
Select "Bluetooth ".
Select "Search ".
A window is displayed with " Searching
device ".
The services available depend on
the network, the SIM card and the
compatibility of the Bluetooth telephone
used.
Check the instructions for your telephone
and with your ser vice provider for the
ser vices to which you have access.
In the list, select a telephone to pair.
Confirm with " OK".
Only one telephone can be paired at a time.
In some cases, the Bluetooth address of the
telephone may appear instead of the name of
the telephone. A virtual keypad is displayed on the
screen: choose a 4-digit code.
Confirm with "
OK".
A message is displayed on the screen of the
telephone: enter the same code and confirm.
If pairing fails, the number of attempts is not
restricted.
A message appears in the screen to confirm
the result of the connection. Pairing can also be initiated from the
telephone by searching for detected
Bluetooth devices.
The directory and the call list can
be accessed after the necessary
synchronisation period (if the telephone is
compatible).
Automatic connection must be configured
in the telephone to allow the connection
each time the vehicle is started.Managing connections
Press the MENU button.
Select " Bluetooth ".
Select " BT management "
and confirm. The list of paired
telephones is displayed.
Indicates connection of the audio
profile.
Indicates the hands-free telephone
profile.
In the list, select a telephone to pair.
Confirm with " OK".
.
Audio system / Bluetooth®

10
"Delete " to delete the pairing.
It is not possible to pair more than 5
telephones, Press MENU and select
" Bluetooth ". Select "BT management ". If
5 telephones are already paired, select the
telephone to delete by pressing " OK" and
selecting " Delete" (refer to the "Managing
connections" section).
Making a call
From the directory
Press the MENU button. Select
"Telephone ".
Select "Call ".
Select "Directory ".
Select the desired number.
Confirm with "OK " to start the call.
Making a call
Recently called numbers
(Depending on the compatibility of the phone)
Press and hold SRC/TEL to display
the calls list. For access to the call list, it is also
possible to press MENU
, select
" Telephone ", then select " Call" and finally
select " Calls list ".
In the list of calls, select from:
" Missed calls ", "Dialled calls " or
" Answered calls ".
Scroll through the calls list.
Confirm with " OK".
Press one of these buttons to go to
the previous or next page in the list.
" OK " starts the call.
Select or deselect:
-

"
Te l . ": hands-free connection
-

"
Audio ": play audio files
" OK " to confirm the choice.
Audio system / Bluetooth®