2017 Peugeot 208 Owner's Manual

119
With BlueHDi Diesel and a manual gearbox:
- A s soon as the vehicle stops or the speed is
less than 2
mph (3 km/h) (with 1.5 Blue HDi
engine).
-

G
ear lever in neutral and clutch pedal
released.
With PureTech petrol and a manual,
electronic or automatic gearbox :
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on which version
you have).
-

G
ear lever in neutral and clutch pedal
released (manual gearbox).
-

B
rake pedal pressed or gear lever in
position N (electronic or automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not invoked when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-

d
emisting is active, The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
A time counter sums up the time
periods spent in STOP mode
during a journey. It resets every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as for
example, braking, power steering, With a manual gearbox in STOP mode, if
a gear is engaged without fully depressing
the clutch pedal, a warning lamp comes
on or an alert message is displayed asking
you to depress the clutch pedal to restart
the engine.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
START mode
The ECO warning lamp goes off and
the engine starts:
With a manual gearbox :
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released.
or
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the engine
is needed to control the system.
6
Driving

120
- Gear lever in position N.
- Brake pedal released.
-

T
hen gear lever in position A / D or M .
or
-
R

everse gear engaged.
Special cases: START invoked
automatically
As a safety measure and for your comfort,
START mode is invoked automatically when:
-
y
ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) where the
engine is needed for control of the system
or vehicle.
The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
Manual deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in the
passenger compartment, it may be preferable
to deactivate the Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
This control switches off the Stop & Start
system.
-
Press.
-

T
he indicator lamp in the control remains
on.
-

A m
essage is displayed.
If you are stationary in Stop mode, the engine
restarts immediately.
Manual reactivation
- Press.
- T he indicator lamp in the control goes off.
-

A c
onfirmation message is displayed. If the engine is in STOP mode, it restarts
immediately.
The Stop & Start system is reactivated
automatically every time the ignition is
switched on.
Opening the bonnet
Before doing anything under the bonnet,
deactivate the Stop & Start system to
avoid the risk of injury related to an
automatic change to START mode.
Driving on flooded roads
Before driving in a flooded area, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice
,
particularly on flooded roads, refer to the
corresponding section.
Driving

121
Operating fault
In the event of a fault with the system, the ECO
OFF switch warning lamp flashes then comes
on fixed.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
If a fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.The Stop & Start system requires a
12
V battery of specific technology and
specification.
All work on this type of battery must be
carried out only by a PEUGEOT dealer or
a qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter On / Pause. The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use of
the limiter, simply reduce the pressure on the
accelerator pedal gradually and return to a
speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
Selection
F Place the thumbwheel at the "LIMIT"

position: the speed limiter mode is selected
but is not switched on (PAUSE).
Switching the speed limiter on is not required to
set the speed limit.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 20

mph
(30


km/h).
6
Driving

122
Registering a limit speed
This can be done without switching the limiter
on, but the engine must be running.
To register a speed higher than the previous
setting:
-

P
ress the SET +
button.
A short press increases the speed setting by
1
mph (km/h).
Pressing and holding increases the setting in
steps of 5
mph (km/h).
To register a speed lower than the previous
setting:
-

P
ress the SET –
button. A short press decreases the setting by 1
mph
(km/h).
Pressing and holding decreases the setting in
steps of 5 mph (km/h).
On / Pause
A first press on this button switches the speed
limiter on, a second press pauses it.
Exceeding the registered
limit speed
Pressing the accelerator pedal to
exceed the registered speed will not
have any effect, unless you press
the pedal firmly
past the point of
resistance .
The speed limiter is deactivated temporarily
and the registered speed setting flashes,
accompanied by an audible signal.
To return to normal operation of the speed
limiter, reduce your speed to below the
registered speed setting.
Flashing of the speed setting
It flashes:
- a fter forcing the accelerator pedal past the
point of resistance,
-

w
hen the limiter cannot prevent the speed
of the vehicle increasing, because of the
profile of the road or when going down a
steep hill,
-

u
nder sharp acceleration.
F

P
lace the thumbwheel at the 0 position or
switch off the ignition to stop the system.
The last speed registered stays in memory.
Switching the system off
Driving

123
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.In any event, the speed limiter cannot
replace the need to obser ve speed limits,
nor can it replace the need for vigilance on
the part of the driver.
Always pay attention to the profile of the
road and sharp acceleration and stay in
complete control of your vehicle.
To avoid any jamming under the pedals:
-

e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever place one mat on top of another.
Cruise control "CRUISE"
System which automatically maintains the
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
Steering mounted controls
1.Cruise control mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Pause / Resume cruise control. This driving assistance system, for use when
the traffic is flowing, allows a speed set by
the driver to be maintained, except on a steep
gradient.
With a manual gearbox
In order for it to be programmed or activated,
the vehicle speed must be greater than 25
mph
(40 km/h) with 4
th gear or higher engaged.
With an electronic gearbox
To be registered or activated, the speed of the
vehicle must be above 25
mph (40 km/h) with
2
nd gear or higher engaged in manual mode, or
position A selected.
With an automatic gearbox
To be registered or activated, the speed of the
vehicle must be above 25
mph (40 km/h) with
2
nd gear or higher engaged in manual mode, or
position D selected.
Selection
F Place the thumbwheel at the "CRUISE"
position: the cruise control mode is selected
but is not switched on (PAUSE).
6
Driving

124
Registering a cruise speed
setting
- Bring the vehicle up to the desired speed by pressing the accelerator.
-

P
ress the SET – or
SET + button.
The speed setting is registered/activated and
the vehicle will maintain this speed.
Temporarily exceeding the
programmed speed
It is possible to accelerate and
temporarily drive at a speed higher
than the registered speed setting.
The cruise speed setting value
flashes.
When the accelerator pedal is
released, the vehicle will return to
the registered speed setting.
Pause (OFF)
- Press this button or the brake or clutch pedal (depending on the version). With 1.2 PureTech 82 and 110 (Euro
6.2)
or 1.5 BlueHDi (Euro 6.2) engines, a
manual gearbox and the Stop & Start,
pressing the clutch pedal does not pause
the cruise control, the cruise control
remains active after changing gears.
Resume
- After the cruise control has been paused, press this button.
The vehicle returns to the last registered speed.
Alternatively, you can also resume the
procedure for "Registering a cruise speed
setting".
Driving

125
To register a speed higher than the previous
setting, there are two possibilities.
Without using the accelerator
- Press the SET + button.
A short press increases the speed setting by
1

mph (km/h).
Pressing and holding increases the setting in
steps of 5

mph (km/h).
By using the accelerator
- Exceed the saved speed until you reach the desired speed. -

P
ress the SET – or
SET + button.
To register a speed lower than the previous
setting:
-
P
ress the SET –
button.
A short press decreases the setting by 1 mph
(km/h).
Pressing and holding decreases the setting in
steps of 5 mph (km/h).
Switching the system off
- Place the thumbwheel at the 0 position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Changing the registered
speed setting
6
Driving

126
When changing the programmed
reference speed by means of a maintained
press, pay attention as the speed can
increase or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the registered speed.
The cruise control system cannot in
any circumstances replace the need
to obser ve speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming the pedals:
-
e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever place one mat on top of another.Memorising speeds
This function allows speeds to be saved, which
can then be offered to set the two systems: the
speed limiter (to limit the speed of the vehicle)
or the cruise control (for a vehicle cruising
speed).
You can memorise up to five settings in the
system for each of the two systems.
By default, some speed settings are already
memorised.
With touch screen
This memorisation can be
configured from the menu Driving /
Vehicle .
F

Sel

ect the " Driving functions " tab.
F

Sel

ect the " Adjusting Speeds " function.
F

P

ress " ON" to activate the function.
F

Sel

ect the speed setting 1 to 5 that you want
to change.
F

S

elect the speed setting value you want to
change.
F

E

nter the new value using the numerical
keypad and confirm and click on " OK" to
confirm. As a safety measure, the driver must carry
out these operations when stationary.
Selection
To select a memorised speed:
F
P ress and hold the " +" or " -" button; the
system stops at the nearest memorised
speed.
F

P
ress and hold again the " +" or " -" button to
select another memorised speed.
A reminder of the speed and the state of the
system (on / off) is displayed in the instrument
panel.
Driving