2017 MAZDA MODEL CX-5 ignition

4–8
When Driving
Start/Stop Engine
7. Press the push button start after both the KEY indicator light (green) (if
equipped) in the instrument cluster and
the push button start indicator light
(green) illuminate.
NOTE
  After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
  After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.

8. After starting the engine, let it idle for about ten seconds.
NOTE
  Whether the engine is cold or warm, it
should be started without the use of the
accelerator.
  If the engine does not start the fi rst
time, refer to Starting a Flooded Engine
under Emergency Starting. If the engine
still does not start, have your vehicle
inspected by an Authorized Mazda
Dealer (page 7-17 ).

Engine Start Function When Key Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not
to allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.
 Metal parts of other keys or metal
objects touch the key.

 Spare keys or keys for other vehicles equipped with an immobilizer
system touch or come near the key.

 Devices for electronic purchases, or security passage touch or come near
the key.

CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:05:41

4–9
When Driving
Start/Stop Engine
If the engine cannot be started due to a
dead key battery, the engine can be started
using the following procedure:

1. Continue to depress the brake pedal fi rmly until the engine has completely
started.
2. (Manual transaxle)
Continue to depress the clutch pedal fi rmly until the engine has completely
started.
3. Verify that the push button start indication light (green) fl ashes.
4. Touch the push button start using the backside of the key (as shown) while
the push button start indicator light
(green) fl ashes.


Push button start
Indicator light
Key

NOTE
When touching the push button start using
the backside of the key as shown in the
illustration, touch the push button start
with the lock switch side of the key facing
up.

5. Verify that the push button start indicator light (green) turns on. 6. Press the push button start to start the
engine.
NOTE
  The engine cannot be started unless the
clutch pedal is fully depressed (manual
transaxle) or the brake pedal is fully
depressed (automatic transaxle).
  If there is a malfunction with the push
button start function, the push button
start indicator light (amber) fl ashes.
In this case, the engine may start,
however, have the vehicle checked at an
Authorized Mazda Dealer as soon as
possible.
   If the push button start indicator light
(green) does not illuminate, perform the
operation from the beginning again. If
it does not illuminate, have the vehicle
checked at an Authorized Mazda Dealer.
  To switch the ignition position without
starting the engine, perform the
following operations after the push
button start indicator light (green) turns
on.

1. Release the clutch pedal (manual transaxle) or brake pedal (automatic
transaxle).
2. Press the push button start to switch the ignition position. The ignition
switches in the order of ACC, ON,
and off each time the push button
start is pressed. To switch the
ignition position again, perform the
operation from the beginning.


CX-5_8FN1-EA-16L_Edition1.indb 92016/12/12 10:05:41

4–10
When Driving
Start/Stop Engine
Emergency Operation for Starting the Engine
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) fl ashes, this could indicate that
the engine may not start using the usual
starting method. Have your vehicle
inspected at an Authorized Mazda Dealer
as soon as possible. If this occurs, the
engine can be force-started. Press and hold
the push button start until the engine starts.
Other procedures necessary for starting the
engine such as having the key in the cabin,
and depressing the clutch pedal (manual
transaxle) or the brake pedal (automatic
transaxle) are required.
Turning the Engine Off
WARNING
Do not stop the engine while the vehicle
is moving: Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking, which
could cause an accident and serious
injury.

1. Stop the vehicle completely.
2. (Manual transaxle)
Shift into neutral and set the parking brake.
(Automatic transaxle)
Shift the selector lever to the P position and set the parking brake.
3. Press the push button start to turn off the engine. The ignition position is off.

CAUTION
When leaving the vehicle, make sure
the push button start is off .

CX-5_8FN1-EA-16L_Edition1.indb 102016/12/12 10:05:41

4–11
When Driving
Start/Stop Engine
NOTE
  The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
  If the system detects that the remaining
battery power of the key is low when the
ignition is switched from ON to ACC or
OFF, the following is indicated.
 Replace with a new battery before the key becomes unusable.
 Refer to Key Battery Replacement on page 6-36 .
 (Vehicle equipped with Type A
instrument cluster)
 A message is indicated in the display of
the instrument cluster.
 (Vehicle equipped with Type B
instrument cluster)
 The KEY indicator light (green) fl ashes
for approximately 30 seconds.
 Refer to Warning/Indicator Lights on page 4-32 .
  (Automatic transaxle)  If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.

Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
CX-5_8FN1-EA-16L_Edition1.indb 112016/12/12 10:05:41

4–15
When Driving
Instrument Cluster and Display
Engine Coolant Temperature Gauge (Without Multi-information
Display)
Displays the engine coolant temperature.
The white gauge indicates that the engine
coolant temperature is low, and the red
gauge indicates that the engine coolant
temperature is high and overheating.


CAUTION
If the engine coolant temperature
gauge indicator fl ashes, there is a
possibility of overheating. Park the
vehicle in a safe place immediately
and take appropriate measures. If the
vehicle continues to be driven, it could
cause damage to the engine.
Refer to Overheating on page 7-18 .

NOTE
  The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with
the temperature unit of the outside
temperature display.
 Refer to Personalization Features on page 9-11 .
  During normal driving, the engine
coolant temperature stabilizes at
100 °C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F).
  If the engine load increases and the
engine coolant temperature exceeds
100 °C (210 °F), the gauge indicates the
engine coolant temperature.

Fuel Gauge (Without Multi-information Display)
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full.


Full
1/4 Full
Empty

If the low fuel warning light illuminates or
the fuel level is very low, refuel as soon as
possible.
Refer to Warning Indication/Warning
Lights on page 4-33 .
CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:05:42

4–16
When Driving
Instrument Cluster and Display
NOTE
  After refueling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve since
the fuel moves in the tank.
  The display indicating a quarter or less
remaining fuel has more segments to
show the remaining fuel level in greater
detail.
  The direction of the arrow ( )
indicates that the fuel- fi ller lid is on the
left side of the vehicle.

Dashboard Illumination
(Without auto-light control)
When the position lights are turned
on with the ignition switched ON, the
brightness of the dashboard illumination is
dimmed.
(With auto-light control)
When the position lights are turned
on with the ignition switched ON, the
brightness of the dashboard illumination
is dimmed. However, when the light
sensor detects that the surrounding area is
bright such as when the position lights are
turned on in the daytime, the dashboard
illumination does not dim.
NOTE
   (With auto-light control)  When the ignition is switched ON in the
early evening or at dusk, the dashboard
illumination is dimmed for several
seconds until the light sensor detects
the brightness of the surrounding area,
however, the dimmer may cancel after
the brightness is detected.
  When the position lights are turned on,
the position lights indicator light in the
instrument cluster turns on.
 Refer to Headlights on page 4-51 .
The brightness of the instrument cluster
and dashboard illuminations can be
adjusted by rotating the knob.
  The brightness decreases by rotating the
knob to the left. A beep sound will be
heard when the knob has been rotated to
the maximum dim position.
   The brightness increases by rotating the
knob to the right.


Dim
Bright

Function for cancelling illumination
dimmer
The illumination dimmer can be canceled
by rotating the dashboard illumination
knob to the right until a beep sound is
heard while the instrument cluster is
dimmed with the ignition switched ON.
If the instrument cluster's visibility is
reduced due to glare from surrounding
brightness, cancel the illumination
dimmer.
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:05:43

4–17
When Driving
Instrument Cluster and Display
NOTE
  (With Multi-information Display)  The illumination dimmer can be
canceled by pressing the dashboard
illumination knob.
  When the illumination dimmer is
canceled, the instrument cluster cannot
be dimmed even if the position lights are
turned on.
  When the illumination dimmer is
canceled, the screen in the center
display switches to constant display of
the daytime screen.

Outside Temperature Display (Without Multi-information
Display)
When the ignition is switched ON, the
outside temperature is displayed.



NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and vehicle
conditions:
  Signifi cantly cold or hot temperatures.  Sudden changes in outside temperature.  The vehicle is parked.  The vehicle is driven at low speeds.

Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and Fahrenheit.
Settings can be changed by operating the
center display screen.
Refer to Personalization Features on page
9-11 .
NOTE
When the temperature unit indicated in the
outside temperature display is changed,
the temperature unit indicated in the
engine coolant gauge display changes in
conjunction with it.

Cruise Control Set Vehicle Speed
Display (Without Multi-
information Display)
The vehicle speed preset using the cruise
control is displayed.



Trip Computer and INFO Switch (Without Multi-information
Display)
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
   Distance-to-empty mode  Average fuel economy mode  Current fuel economy mode  Compass mode
If you have any problems with your trip
computer, consult an Authorized Mazda
Dealer.
CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:05:43

4–22
When Driving
Instrument Cluster and Display
Odometer, Trip Meter and Trip Meter Selector
The odometer is constantly displayed on
the screen when the ignition is switched
ON, and the TRIP A or TRIP B screen
can be displayed by operating the INFO
switch.


Press the INFO switch INFO switch
Odometer,
Trip meter A
Odometer,
Trip meter B

Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The driving distance for a speci fi ed
interval is indicated. Two types (TRIP
A, TRIP B) of interval distance and the
average fuel economy for each can be
measured.

For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is fi lled.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter and average fuel economy
can be reset by pressing the INFO switch
for 1.5 second or more while in each
mode.
NOTE
   Only the trip meters record tenths of
kilometers (miles).
  The trip record will be erased when:   The power supply is interrupted
(blown fuse or the battery is
disconnected).
  The vehicle is driven over 1999 km
(mile).


CX-5_8FN1-EA-16L_Edition1.indb 222016/12/12 10:05:44