2017 MAZDA MODEL CX-5 ignition

3–15
Before Driving
Doors and Locks
NOTE
  The system can be set to unlock all
doors by performing a single operation.
 Refer to Personalization Features on page 9-11 .
 Use the following procedure to change the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
UNLOCK button on the key for
5 seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the setting of pressing the driver's
request switch once or twice to
unlock all doors and the liftgate
each time the UNLOCK button is
pressed (the sound of the doors
locking/unlocking can be heard).
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
UNLOCK button on the key.
  Pressing a request switch.   Confi rm that all doors and the liftgate
are securely locked.
 For the liftgate, move it without pressing the electric liftgate opener to
verify that the liftgate has not been left
ajar.
  All doors and the liftgate cannot be
locked when any door or the liftgate is
open.
  It may require a few seconds for the
doors to unlock after the request switch
is pressed.
  A beep sound is heard for confi rmation
when the doors and the liftgate are
locked/unlocked using the request
switch. If you prefer, the beep sound can
be turned off.
 The volume of the beep sound can also be changed. Refer to Personalization
Features on page 9-11 .
 Use the following procedure to change
the setting.

1. Switch the ignition off and close all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's door, press and hold the
LOCK button on the key for
5 seconds or longer.
All of the doors and the liftgate lock and the beep sound activates at the
currently set volume. The setting
changes each time the LOCK button
on the key is pressed and the beep
sound activates at the set volume. (If
the beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed by doing any one of the following:
  Switching the ignition to ACC or
ON.
  Closing the driver's door.  Opening the liftgate.  Not operating the key for
10 seconds.
  Pressing any button except the
LOCK button on the key.
  Pressing a request switch.
CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:05:30

3–16
Before Driving
Doors and Locks
  (With theft-deterrent system)  The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on page 3-47 .
  The setting can be changed so that
the doors and the liftgate are locked
automatically without pressing the
request switch.
 Refer to Personalization Features on page 9-11 .
 (Auto-lock function)  A beep sound is heard when all doors
and the liftgate are closed while the
advanced key is being carried. All doors
and the liftgate are locked automatically
after about three seconds when the
advanced key is out of the operational
range. Also, the hazard warning lights
fl ash once. (Even if the driver is in the
operational range, all doors and the
liftgate are locked automatically after
about 30 seconds.) If you are out of
the operational range before the doors
and the liftgate are completely closed
or another key is left in the vehicle, the
auto-lock function will not work. Always
make sure that all doors and the liftgate
are closed and locked before leaving the
vehicle. The auto-lock function does not
close the power windows.
   Auto re-lock function  After unlocking with the request
switch, all doors and the liftgate
will automatically lock if any of the
following operations are not performed
within about 60 seconds. If your
vehicle has a theft-deterrent system,
the hazard warning lights will fl ash for
confi rmation.
 The time required for the doors to lock
automatically can be changed.
 Refer to Personalization Features on page 9-11 .
  Opening a door or the liftgate.  Switching the ignition to any position
other than off.


Locking, Unlocking with Transmitter
All doors and the liftgate can be locked/
unlocked by operating the keyless entry
system transmitter, refer to Keyless Entry
System (page 3-3 ).
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:05:30

3–17
Before Driving
Doors and Locks
Locking, Unlocking with Door-Lock Switch
All doors and the liftgate lock
automatically when the lock side is
pressed. They unlock when the unlock side
is pressed.
Driver's door

Unlock
Lock

Front passenger's door

Unlock
Lock

To lock all the doors and the liftgate from
an open front door, press the lock side of
the door lock switch and then close the
door.
NOTE
When locking the doors this way, be
careful not to leave the key inside the
vehicle.

Auto Lock/Unlock Function
WARNING
Do not pull the inner handle on a front
door: Pulling the inner handle on a front
door while the vehicle is moving
is dangerous. Passengers can fall
out of the vehicle if the door opens
accidentally , which could result in
death or serious injury.
  When the vehicle speed exceeds
20 km/h (12 mph), all doors and the
liftgate lock automatically.
   When the ignition is switched off,
all doors and the liftgate unlock
automatically.

These functions can also be disabled so
that they do not operate.
Auto lock/unlock function setting
change using door-lock switch
The doors and the liftgate can be set to
lock or unlock automatically by selecting
any one of the functions from the
following table and using the driver's door-
lock switch on the interior door panel.
CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:05:30

3–18
Before Driving
Doors and Locks
NOTE
  Function number 3 in the following
table is the factory setting for your
vehicle.
  There are only a total of six auto lock/
unlock settings available for automatic
transaxle vehicles, and three for manual
transaxle vehicles. Be sure to press the
unlock side of the driver's door-lock
switch the correct number of times
according to the selected function
number. If the switch is mistakenly
pressed seven times on an automatic
transaxle vehicle or four times on a
manual transaxle, the procedure will
be cancelled. If this occurs, start the
procedure from the beginning.


Function number Function *1
1 The auto door-lock function is
disabled.
2 All the doors and the liftgate lock
automatically when the vehicle speed
is about 20 km/h (12 mph) or more.
3 (Factory Setting) All the doors and the liftgate lock
automatically when the vehicle speed
is about 20 km/h (12 mph) or more.
All the doors and the liftgate unlock
when the ignition is switched from
ON to Off.
4 (Automatic transaxle vehicles only)

When the ignition is switched ON
and the selector lever is shifted from
park (P) to any other gear position,
all the doors and the liftgate lock
automatically.
5 (Automatic transaxle vehicles only)

When the ignition is switched ON
and the selector lever is shifted from
park (P) to any other gear position,
all the doors and the liftgate lock
automatically.
When the selector lever is shifted to
park (P) while the ignition is switched
ON, all the doors and the liftgate
unlock automatically.
6 (Automatic transaxle vehicles only)

All the doors and the liftgate lock
automatically when the vehicle speed
is about 20 km/h (12 mph) or more.
When the selector lever is shifted to
park (P) while the ignition is switched
ON, all the doors and the liftgate
unlock automatically.
*1 Other settings for the auto door lock function are available at an Authorized Mazda Dealer. For
details consult an Authorized Mazda Dealer. Refer
to Personalization Features on page 9-11 .


CX-5_8FN1-EA-16L_Edition1.indb 182016/12/12 10:05:31

3–19
Before Driving
Doors and Locks
Settings can be changed using the
following procedure.

1. Safely park the vehicle. All doors must remain closed.
2. Switch the ignition ON.
3. Press and hold the lock side of the driver's door-lock switch within
20 seconds of switching the ignition
ON, and make sure a beep sound is
heard about eight seconds afterwards.
4. Refer to the auto lock/unlock function setting table, determine the function
number for the desired setting. Press
the unlock side of the driver's door-lock
switch the same number of times as the
selected function number (Ex. If you
select function 2, press the unlock side
of the switch only 2 times).
5. Three seconds after the function setting has been changed, a beep sound will
beep in the amount of the selected
function number. (Ex. Function number
3 = 3 beep sounds)

(Manual transaxle vehicles)

Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Function Number 3 Press 4 times
Press unlock side of
lock switch once
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
Wait for 3 second
(Automatic transaxle vehicles)


Press unlock side of
lock switch once
Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Press 4 times
Function Number 3
Press 5 times
Function Number 4
Press 7 times
Function Number 5
Press 6 times
Function Number 6
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
Wait for 3 second

NOTE
   The doors cannot be locked or unlocked
while the setting function is being
performed.
  The procedure can be cancelled by
pressing the lock side of the driver's
door-lock switch.

CX-5_8FN1-EA-16L_Edition1.indb 192016/12/12 10:05:31

3–26
Before Driving
Doors and Locks
Operation using the transmitter
Press the power liftgate button for one
second or more. The hazard warning lights
fl ash twice and the liftgate opens/closes
after the beep sounds.
Refer to Transmitter on page 3-5 .
NOTE
   When the ignition is switched ON, the
transmitter does not operate.
  When opening the liftgate by pressing
the power liftgate button on the
transmitter, the liftgate can be opened
even when it is locked.
  If the power liftgate button on the
transmitter is pressed while the liftgate
is opening/closing electrically, the
beep is activated and the liftgate stops.
When pressing the power liftgate button
again, the liftgate moves in the reverse
direction.

Operation using each switch
Operation conditions
Opening the liftgate
If the vehicle has satis fi ed all the following
operation conditions, the power liftgate
can be opened using the power function.
   All doors and the liftgate are unlocked.  The ignition is switched OFF, or the
selector lever is in P with the ignition
switched ON.

Closing the liftgate    The ignition is switched OFF, or the
selector lever is in P with the ignition
switched ON.

NOTE
If the vehicle moves with the selector lever
shifted to a position other than P while the
liftgate is opening/closing electrically, the
liftgate moves as follows:
While opening electrically
The buzzer is activated, and the
liftgate moves in the reverse direction
automatically and closes. When the
selector lever is shifted to P, you can
resume the power liftgate operation using
the switches.
While closing electrically
The buzzer is activated, but the liftgate
continues closing.

Operation from the driver's seat (To
open/close)
Press the power liftgate switch for about
one second or more while the liftgate is in
the fully closed/open position. The hazard
warning lights fl ash twice and the liftgate
opens/closes fully after the beep sound is
heard.

Power liftgate switch

CX-5_8FN1-EA-16L_Edition1.indb 262016/12/12 10:05:32

3–31
Before Driving
Fuel and Emission
Emission Control System
This vehicle is equipped with an emission control system (the catalytic converter is
part of this system) that enables the vehicle to comply with existing e\
xhaust emissions
requirements.
WARNING
Never park over or near anything fl ammable:
Parking over or near anything fl ammable, such as dry grass, is dangerous. Even with the
engine turned off , the exhaust system remains very hot after normal use and could ignite
anything fl ammable. A resulting fi re could cause serious injury or death.

CAUTION
Ignoring the following precautions could cause lead to accumulate on the catalyst inside
the converter or cause the converter to get very hot. Either condition will damage the
converter and cause poor performance.
 USE ONLY UNLEADED FUEL. Do not drive your Mazda with any sign of engine malfunction. Do not coast with the ignition switched off . Do not descend steep grades in gear with the ignition switched off . Do not operate the engine at high idle for more than 2 minutes. Do not tamper with the emission control system. All inspections and adjustments must
be made by a qualifi ed technician.
 Do not push-start or pull-start your vehicle.
NOTE
   Under U.S. federal law, any modifi cation to the original-equipment emission control
system before the fi rst sale and registration of a vehicle is subject to penalties. In some
states, such modifi cation made on a used vehicle is also subject to penalties.
  While the engine is off, the sound of a valve opening and closing can be\
heard at the rear
of the vehicle, however this does not indicate an abnormality. The vehicle has a self-
checking device and it operates while the engine is off.

CX-5_8FN1-EA-16L_Edition1.indb 312016/12/12 10:05:33

3–35
Before Driving
Steering Wheel
*Some models.
Steering Wheel
WARNING
Never adjust the steering wheel while
the vehicle is moving: Adjusting the steering wheel while
the vehicle is moving is dangerous.
Moving it can very easily cause the
driver to abruptly turn to the left or
right. This can lead to loss of control or
an accident.

Steering Wheel Adjustment
To change the angle or length of the
steering wheel:

1. Stop the vehicle, and then pull down the lock release lever under the steering
column.


Lock release lever
2. Tilt the steering wheel and/or adjust the steering column length to the desired
positions, then push the lever up to lock
the column.
3. Attempt to push the steering wheel up and down to make sure it's locked
before driving.

Heated Steering Wheel *
The grips on the left and right of the
steering wheel can be warmed up.

Heated steering
wheel switchHeating area

The ignition must be switched ON.

Press the switch to turn on the heated
steering wheel. The heated steering wheel
operates for about 30 minutes and then
turns off automatically.
The indicator light illuminates when the
heater is operating.

To turn off the heated steering wheel
before the 30 minutes has elapsed, press
the switch again.
CAUTION
The following types of persons should
be careful not to touch the steering
wheel. Otherwise, it could cause a low-
temperature burn.
 Infants, small children, elderly people, and physically challenged
people
 People with delicate skin People who are excessively fatigued People who are intoxicated People who have taken sleep-inducing medicine such as sleeping
pills or cold medicine

CX-5_8FN1-EA-16L_Edition1.indb 352016/12/12 10:05:34