2017 MAZDA MODEL 2 wheel

4–16 8
When Driving
i-ACTIVSENSE
NOTE
  The Smart Brake Support (SBS) system operates when all of the following conditions
are met:
 


 The ignition is switched ON.



 The Smart Brake Support (SBS) system is on.



 The vehicle speed is about 15 km/h or faster (10 mph or faster).



 The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


 The Dynamic Stability Control (DSC) is not operating. 

 The Smart Brake Support (SBS) system may not operate under the following
conditions:
 


 If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



 The vehicle is driven at the same speed as the vehicle ahead.



 The accelerator pedal is depressed.



 The brake pedal is depressed.



 The steering wheel is being operated.



 The selector lever is being operated.



 The direction indicator is being used.



 When the vehicle ahead is not equipped with tail lights or the tail lights are turned
off.
 


 When warnings and messages, such as a dirty windscreen, related to the Forward
Sensing Camera (FSC) are being displayed in the centre display.
 
 Although the objects which activate the system are four-wheeled vehicles, the radar
sensor (front) could detect the following objects, determine them to be an obstruction,
and operate the Smart Brake Support (SBS) system.
 


 Objects on the road at the entrance to a curve (including guardrails and snow banks).



 A vehicle appears in the opposite lane while cornering or rounding a curve.



 When crossing a narrow bridge.



 When passing under a low gate or through a tunnel or narrow gate.



 When entering an underground parking area.



 Metal objects, bumps, or protruding objects on the road.



 If you suddenly come close to a vehicle ahead.



 When driving in areas where there is high grass or forage.



 Two-wheeled vehicles such as motorbikes or bicycles.



 Pedestrians or non-metallic objects such as standing trees. 

 When the system operates, the user is noti¿ ed by the active driving display. 
 The Smart Brake Support (SBS) warning indication (amber) turns on when the system
has a malfunction.
 Refer to Warning Lights on page 4-38 .

4–172
When Driving
i-ACTIVSENSE
CAUTION
  Heed the following cautions to assure the correct operation of the Forward Sensing
Camera (FSC).
 


 Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get
dirty.
 


 Do not remove the Forward Sensing Camera (FSC) cover.



 Do not place objects on the instrument panel which reÀ ect light.



 Always keep the windscreen glass around the camera clean by removing dirt or
fogging. Use the windscreen defroster to remove fogging on the windscreen.
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer regarding
cleaning the interior side of the windscreen around the Forward Sensing Camera
(FSC).
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer before
performing repairs around the Forward Sensing Camera (FSC).
 


 The Forward Sensing Camera (FSC) is installed to the windscreen. Consult an expert
repairer, we recommend an Authorised Mazda Repairer for windscreen repair and
replacement.
 


 When cleaning the windscreen, do not allow glass cleaners or similar cleaning À uids
to get on the Forward Sensing Camera (FSC) lens. In addition, do not touch the
Forward Sensing Camera (FSC) lens.
 


 When performing repairs around the rearview mirror, consult an expert repairer, we
recommend an Authorised Mazda Repairer.
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer regarding
cleaning of the camera lens.
 


 Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area
around it. If the Forward Sensing Camera (FSC) is severely hit or if there are cracks
or damage caused by À ying gravel or debris in the area around it, stop using the
following systems and consult an expert repairer, we recommend an Authorised
Mazda Repairer.
 


 High Beam Control System (HBC)



 Adaptive LED Headlights (ALH)



 Lane Departure Warning System (LDWS)



 Driver Attention Alert (DAA)



 Smart Brake Support (SBS) 



 The direction in which the Forward Sensing Camera (FSC) is pointed has been ¿ nely
adjusted. Do not change the installation position of the Forward Sensing Camera
(FSC) or remove it. Otherwise, it could result in damage or malfunction.


 Always use tyres for all wheels that are of the speci¿ ed size, and the same
manufacturer, brand, and tread pattern. In addition, do not use tyres with signi¿ cantly
different wear patterns on the same vehicle as the system may not operate normally.

4–17 8
When Driving
i-ACTIVSENSE
NOTE
  Under the following conditions, the radar sensor (front) may not be able to detect
vehicles ahead or obstructions correctly and each system may not operate normally.
 


 The rear surface of a vehicle ahead does not reÀ ect radio waves effectively, such as
an unloaded trailer or an automobile with a loading platform covered by a soft top,
vehicles with a hard plastic tailgate, and round-shaped vehicles.
 


 Vehicles ahead with low vehicle height and thus less area for reÀ ecting radio waves.



 Visibility is reduced due to a vehicle ahead casting off water, snow, or sand from its
tyres and onto your windscreen.
 


 The boot/luggage compartment is loaded with heavy objects or the rear passenger
seats are occupied.
 


 Ice, snow, or soiling is on the front surface of the front emblem.



 During inclement weather such as rain, snow, or sand storms.



 When driving near facilities or objects emitting strong radio waves. 

 Under the following conditions, the radar sensor (front) may not be able to detect
vehicles ahead or obstructions.
 


 The beginning and end of a curve.



 Roads with continuous curves.



 Narrow lane roads due to road construction or lane closures.



 The vehicle ahead enters the radar sensor's blind spot.



 The vehicle ahead is running abnormally due to accident or vehicle damage.



 Roads with repeated up and down slopes



 Driving on poor roads or unpaved roads.



 The distance between your vehicle and the vehicle ahead is extremely short.



 A vehicle suddenly comes close such as by cutting into the lane. 

 To prevent incorrect operation of the system, use tyres of the same speci¿ ed size,
manufacturer, brand, and tread pattern on all four wheels. In addition, do not use
tyres with signi¿ cantly different wear patterns or tyre pressures on the same vehicle
(Including the temporary spare tyre).
  If the battery power is weak, the system may not operate correctly. 
 If the vehicle is driven on a road with little traf¿ c and few vehicles ahead or
obstructions for the radar sensor (front) to detect, the sensor detects that the radar
sensor (front) is dirty and the Smart Brake Support/Smart City Brake Support (SBS/
SCBS) Warning Light (amber) may be temporarily turned on. However, it does not
indicate a malfunction.

4–182
When Driving
i-ACTIVSENSE
NOTE
  The detection ability of the radar sensors (rear) has limitations. In the following cases,
the detection ability may lower and the system may not operate normally.
 


 The rear bumper near the radar sensors (rear) has become deformed.



 Snow, ice or mud adheres to the radar sensors (rear) on the rear bumper.



 Under bad weather conditions such as rain, snow and fog. 

 Under the following conditions, the radar sensors (rear) cannot detect target objects or
it may be dif¿ cult to detect them.




 Stationary objects on a road or a road side such as small, two-wheeled vehicles,
bicycles, pedestrians, animals, and shopping carts.
 


 Vehicle shapes which do not reÀ ect radar waves well such as empty trailers with a
low vehicle height and sports cars.


 Vehicles are shipped with the direction of the radar sensors (rear) adjusted for each
vehicle to a loaded vehicle condition so that the radar sensors (rear) detect approaching
vehicles correctly. If the direction of the radar sensors (rear) has deviated for some
reason, have the vehicle inspected at an Authorised Mazda Dealer.
  For repairs or replacement of the radar sensors (rear), or bumper repairs, paintwork,
and replacement near the radar sensors, consult an Authorised Mazda Dealer.
  Turn off the system while pulling a trailer or while an accessory such as a bicycle
carrier is installed to the rear of the vehicle. Otherwise, the radio waves emitted by the
radar will be blocked causing the system to not operate normally.
  The radar sensors are regulated by the relevant radio wave laws of the country in
which the vehicle is driven. If the vehicle is driven abroad, authorization from the
country in which the vehicle is driven may be required.

4–190
When Driving
Tyre Pressure Monitoring System
*Some models.
Tyre Pressure Monitoring System *
The Tyre Pressure Monitoring System (TPMS) monitors the air pressure of all four tyres. If
the air pressure of one or more tyres is too low, the system warns the driver by indicating the
tyre pressure monitoring system warning light in the instrument cluster and operating a beep
sound. The system monitors the tyre pressures indirectly using the data sent from the ABS
wheel speed sensors.
To allow the system to operate correctly, the system needs to be initialized with the speci¿ ed
tyre pressure (value on the tyre pressure label). Follow the procedure and perform the
initialization.
Refer to Tyre Pressure Monitoring System Initialization on page 4-192 .
The warning light À ashes when the system has a malfunction.
Refer to Warning Lights on page 4-38 .


ABS wheel speed sensor

4–191
When Driving
Tyre Pressure Monitoring System
CAUTION
  Each tyre, including the spare (if provided), should be checked monthly when cold
and inÀ ated to the inÀ ation pressure recommended by the vehicle manufacturer on the
vehicle placard or tyre inÀ ation pressure label. (If your vehicle has tyres of a different
size than the size indicated on the vehicle placard or tyre inÀ ation pressure label, you
should determine the proper tyre inÀ ation pressure for those tyres.)
 As an added safety feature, your vehicle has been equipped with a tyre pressure
monitoring system (TPMS) that illuminates a low tyre pressure telltale when one or
more of your tyres is signi¿ cantly under-inÀ ated. Accordingly, when the low tyre
pressure telltale illuminates, you should stop and check your tyres as soon as possible,
and inÀ ate them to the proper pressure. Driving on a signi¿ cantly under-inÀ ated tyre
causes the tyre to overheat and can lead to tyre failure. Under-inÀ ation also reduces
fuel ef¿ ciency and tyre tread life, and may affect the vehicle's handling and stopping
ability.
 Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct tyre pressure, even if under-inÀ ation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate
when the system is not operating properly.
 The TPMS malfunction indicator is combined with the low tyre pressure telltale.
When the system detects a malfunction, the telltale will À ash for approximately
one minute and then remain continuously illuminated. This sequence will continue
upon subsequent vehicle start-ups as long as the malfunction exists. When the
malfunction indicator is illuminated, the system may not be able to detect or signal
low tyre pressure as intended. TPMS malfunctions may occur for a variety of reasons,
including the installation of replacement or alternate tyres or wheels on the vehicle that
prevent the TPMS from functioning properly. Always check the TPMS malfunction
telltale after replacing one or more tyres or wheels on your vehicle to ensure that the
replacement or alternate tyres and wheels allow the TPMS to continue to function
properly.
  To avoid false readings, the system samples for a little while before indicating a
problem. As a result it will not instantaneously register a rapid tyre deÀ ation or blow
out.

4–192
When Driving
Tyre Pressure Monitoring System
NOTE
Because this system detects slight changes in tyre conditions, the timing of the warning
may be faster or slower in the following cases:
 
 The size, manufacturer, or the type of tyres is different from the speci¿ cation. 
 The size, manufacturer, or the type of a tyre is different from the others, or the level of
tyre wear is excessively different between them.
  A run-À at tyre, studless tyre, snow tyre, or tyre chains are used. 
 An emergency tyre is used (The tyre pressure monitoring system warning light may
À ash and then continue illuminating).

 A tyre is repaired using the emergency À at tyre repair kit. 
 The tyre pressure is excessively higher than the speci¿ ed pressure, or the tyre pressure
is suddenly lowered for some reason such as a tyre burst during driving.
  The vehicle speed is lower than about 15 km/h (9.3 mph) (including when the vehicle
is stopped), or the drive period is shorter than 5 minutes.
  The vehicle is driven on an extremely rough road or a slippery, icy road. 
 Hard steering and rapid acceleration/deceleration are repeated such as during
aggressive driving on a winding road.
  Load on the vehicle is applied to a tyre such as by loading heavy luggage to one side of
the vehicle.
  System initialization has not been implemented with the speci¿ ed tyre pressure.
Tyre Pressure Monitoring System
Initialization
In the following cases, system
initialization must be performed so that the
system operates normally.
 


 A tyre pressure is adjusted.



 Tyre rotation is performed.



 A tyre or wheel is replaced.



 The battery is replaced or completely
drained.
 


 The tyre pressure monitoring system
warning light is illuminated.

Initialization method

1. Park the car in a safe place and ¿ rmly
apply the parking brake.
2. Let the tyres cool, then adjust the tyre
pressure of all four (4) tyres to the
speci¿ ed pressure indicated on the tyre
pressure label located on the driver's
door frame (door open).
Refer to Tyres on page 9-10 .
3. Switch the ignition ON.

4–198
When Driving
Rear View Monitor
Viewing the Display
Guide lines which indicate the width of the vehicle (yellow) are displayed on the screen as a
reference to the approximate width of the vehicle in comparison to the width of the parking
space you are about to back into.
Use this display view for parking your vehicle in a parking space or garage.

b
a

a) Vehicle width guide lines (yellow)
These guide lines serve as a reference to the approximate width of the vehicle.
b) Distance guide lines.
These guide lines indicate the approximate distance to a point measured from the
vehicle's rear (from the end of the bumper).
 

 
 The red and yellow lines indicate the points about 50 cm (19 in) for the red line and
100 cm (39.3 in) for the yellow lines from the rear bumper (at the centre point of each
of the lines).

CAUTION
The guide lines on the screen are ¿ xed lines. They are not synced to the driver's turning
of the steering wheel. Always be careful and check the area to the vehicle's rear and the
surrounding area directly with your eyes while backing up.