2017 MAZDA MODEL 2 heater

2–7
Essential Safety Equipment
Seats
CAUTION
Do not use organic solvents to clean the
seat. It may damage the seat surface and
the heater.
NOTE
  If the ignition is switched off while
the seat warmer is operating (High,
Mid or Low) and then switched
ON again, the seat warmer will
automatically operate at the
temperature set before switching off
the ignition.
  Use the seat warmer when the engine
is running. Leaving the seat warmer
on for long periods with the engine
not running could cause the battery
power to be depleted.
  The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
Rear Seat
Split/One-piece Folding the
Seatback
By lowering the rear seatback(s) the
luggage compartment space can be
expanded.

3–46
Before Driving
Security System
NOTE
  The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate/boot lid and the bonnet
closed.
 Refer to Transmitter on page 3-4 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door.



 Opening the bonnet.



 Switching the ignition ON. 
 To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
À ash once to indicate that the system
is armed.
Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
 


 Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
 


 Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
 


 Hanging small objects/accessories in
the vehicle, hanging clothing on a coat
hook, or placing other items which can
move easily inside the vehicle.
 


 Parking in an area where there is strong
vibration or loud noise.
 


 When using a high pressure or automatic
car wash.
 


 Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
 


 Doors are locked with a window left
open.
 


 An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.

NOTE
If any door or the liftgate/boot lid
remains closed for 30 seconds, all
the doors and the liftgate/boot lid
automatically re-lock and the theft
deterrent system arms even if a window
is left open.

5–147
Interior Features
Appendix
Operating Tips for CD Player
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in
the CD player may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded optical
components will clear naturally in about
an hour. Wait for normal operation to
return before attempting to use the unit.
Handling the CD player
The following precautions should be
observed.
 


 Do not use deformed or cracked CDs.
The disc may not eject resulting in a
malfunction.

 


 Do not use non-conventional discs such
as heart-shaped, octagonal discs, etc.
The disc may not eject resulting in a
malfunction.


 


 If the memory portion of the CD is
transparent or translucent, do not use the
disc.

Transparent  


 A new CD may have rough edges on its
inner and outer perimeters. If a disc with
rough edges is used, proper setting will
not be possible and the CD player will
not play the CD. In addition, the disc
may not eject resulting in a malfunction.
Remove the rough edges in advance
by using a ball-point pen or pencil
as shown in the following ¿ gure. To
remove the rough edges, rub the side of
the pen or pencil against the inner and
outer perimeter of the CD.

 


 When driving over uneven surfaces, the
sound may jump.

5–151
Interior Features
Appendix
Operating Tips for DVD Player
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the DVD or
optical components (prism and lens) in the
DVD player may become clouded with
condensation. At this time, the DVD will
eject immediately when placed in the unit.
A clouded DVD can be corrected simply
by wiping it with a soft cloth. Clouded
optical components will clear naturally in
about an hour. Wait for normal operation
to return before attempting to use the unit.
Handling the DVD player
The following precautions should be
observed.
 


 Do not use deformed or cracked DVDs.
The disc may not eject resulting in a
malfunction.

 


 Do not use non-conventional discs such
as heart-shaped, etc. The disc may not
eject resulting in a malfunction.
 


 If the memory portion of the DVD is
transparent or translucent, do not use the
disc.

Transparent
 


 A new DVD may have rough edges on
its inner and outer perimeters. If a disc
with rough edges is used, proper setting
will not be possible and the DVD player
will not play the DVD. In addition,
the disc may not eject resulting in a
malfunction. Remove the rough edges
in advance by using a ball-point pen
or pencil as shown below. To remove
the rough edges, rub the side of the pen
or pencil against the inner and outer
perimeter of the DVD.

 


 When driving over uneven surfaces, the
sound may jump.

 


 DVDs bearing the logo shown in the
illustration or DVD-R/DVD
R/DVD-
RW/DVD
RW written with video data
(DVD-Video/DVD-VR ¿ le) can be
played.

 


 Use discs that have been legitimately
produced. If illegally-copied discs such
as pirated discs are used, the system may
not operate properly.

6–29
Maintenance and Care
Owner Maintenance
Engine Coolant
Inspecting Coolant Level
WARNING
Do not use a match or live À ame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS
HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.

Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running inde¿ nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.

Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
NOTE
Changing the coolant should be done
by an expert repairer, we recommend an
Authorised Mazda Repairer.
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year—at the beginning of
the winter season—and before travelling
where temperatures may drop below
freezing.

Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.

6–64
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
16 AT PUMP 15 A Transaxle control system
*
17 AT 15 A Transaxle control system *
18 D.LOCK 25 A Power door locks
19 H/L RH 20 A Headlight (RH)
20

7.5 A Engine control system
21 TAIL 20 A Tail lights, Number plate lights, Position lights
22 ST.HEATER 15 A —
— — —
23 ROOM 25 A Overhead light
24 FOG 15 A Front fog lights
*
25 H/CLEAN 20 A Headlight washer *
26 STOP 10 A Brake lights, Rear fog light *
27 HORN 15 A Horn
28 H/L LH 20 A Headlight (LH)
29 ABS/DSC S 30 A ABS, Dynamic stability control system
*
30 HAZARD 15 A Hazard warning À ashers, Direction indicator lights
31 FUEL PUMP 15 A Fuel system
*
32 FUEL WARM 25 A Fuel warmer *
33 WIPER 20 A Front window wiper
34

50 A For protection of various circuits
35 FAN2 30 A Cooling fan
*
36 FUEL PUMP 30 A —
37 ABS/DSC M 50 A ABS, Dynamic stability control system
*
38 EVVT 20 A Engine control system *
39 — — —
40 FAN1 30 A Cooling fan
*
41 FAN3 40 A Cooling fan *
42 ENG.MAIN 40 A Engine control system
43 EPS 60 A Power steering system
*
44 DEFOG 40 A Rear window defogger
45 IG2 30 A For protection of various circuits
46 INJECTOR 30 A Engine control system
*
47 HEATER 40 A Air conditioner
48 P.WINDOW1 30 A Power windows
49 DCDC DE 40 A For protection of various circuits
*

7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning


Master Warning
Light
Vehicles with type B audio
The light turns on when the system has a malfunction.
Operate the centre display and verify the content.
Refer to If a Warning Light Turns On or Flashes on page 7-35 .
Vehicles with type A audio
The light illuminates continuously if any one of the following occurs. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.

There is a malfunction in the battery management system.
There is a malfunction in the brake switch.
(SKYACTIV-D 1.5) There is a malfunction in the engine's hydraulic control.
There is a malfunction in the engine's timing chain.
There is a malfunction in the blow-by heater.
There is a malfunction in the oil level sensor.


Check Engine Light If this light illuminates while driving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an expert repairer, we
recommend an Authorised Mazda Repairer.
The check engine light may illuminate in the following cases:
The engine's electrical system has a problem.
The emission control system has a problem.
(SKYACTIV-G 1.3, SKYACTIV-G 1.5) The fuel tank level being very low or approaching empty.
The fuel-¿ ller cap is missing or not tightened securely. If the check engine light remains on, or it À ashes continuously , do not drive at high speeds
and consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible.


(Amber)
i-stop warning light
*
When the light is turned on
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light does not turn on when the ignition is switched ON.
The light continues to remain on even though the i-stop OFF switch has been pressed
while the engine is running.
When the light is À ashing
The light continues to À ash if the system has a malfunction. Have your vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer.


(Amber)
i-ELOOP Warning
Light
* The light turns on if there is any malfunction in the i-ELOOP system. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.

9–7
Speci¿ cations
Speci¿ cations
Capacities

(Approximate Quantities)
Item Capacity
Engine oil SKYACTIV-G 1.3,
SKYACTIV-G 1.5 With oil ¿ lter replacement 4.2 L (4.4 US qt, 3.7 Imp qt)
Without oil ¿ lter replacement 3.9 L (4.1 US qt, 3.4 Imp qt)
SKYACTIV-D 1.5 With oil ¿ lter replacement 5.1 L (5.4 US qt, 4.5 Imp qt)
Without oil ¿ lter replacement 4.7 L (5.0 US qt, 4.1 Imp qt)
Coolant SKYACTIV-G 1.3 5.2 L (5.5 US qt, 4.6 Imp qt)
SKYACTIV-G 1.5 Manual
transaxle Europe Left-hand drive model 5.4 L (5.7 US qt, 4.8 Imp qt)
Right-hand drive model 5.0 L (5.3 US qt, 4.4 Imp qt)
Russia 5.4 L (5.7 US qt, 4.8 Imp qt)
Israel 5.0 L (5.3 US qt, 4.4 Imp qt)
Except
above
Left-hand drive model *1 5.0 L (5.3 US qt, 4.4 Imp qt)/
5.4 L (5.7 US qt, 4.8 Imp qt)
Right-
hand
drive
model With heater 5.0 L (5.3 US qt, 4.4 Imp qt)
Without
heater 4.5 L (4.8 US qt, 4.0 Imp qt)
Automatic
transaxle Europe Left-hand drive model 5.6 L (5.9 US qt, 4.9 Imp qt)
Right-hand drive model 5.2 L (5.5 US qt, 4.6 Imp qt)
Russia 5.6 L (5.9 US qt, 4.9 Imp qt)
Israel, Saudi Arabia 5.2 L (5.5 US qt, 4.6 Imp qt)
Except
above
Left-hand drive model *1 5.2 L (5.5 US qt, 4.6 Imp qt)/
5.6 L (5.9 US qt, 4.9 Imp qt)
Right-
hand
drive
model With heater 5.2 L (5.5 US qt, 4.6 Imp qt)
Without
heater 4.7 L (5.0 US qt, 4.1 Imp qt)
SKYACTIV-D 1.5 For engine Europe 6.6 L (7.0 US qt, 5.8 Imp qt)
Except
above Left-hand drive model 6.7 L (7.1 US qt, 5.9 Imp qt)
Right-hand drive model 6.8 L (7.2 US qt, 6.0 Imp qt)
For water-cooled charge air cooler 2.0 L (2.1 US qt, 1.8 Imp qt)
Manual
transaxle
oil SKYACTIV-G 1.5 1.59 L (1.68 US qt, 1.40 Imp qt)
SKYACTIV-D 1.5 1.64 L (1.73 US qt, 1.44 Imp qt)
Automatic
transaxle
À uid SKYACTIV-G 1.3, SKYACTIV-G 1.5 7.2 L (7.6 US qt, 6.3 Imp qt)
SKYACTIV-D 1.5 7.8 L (8.2 US qt, 6.9 Imp qt)
Fuel tank 44.0 L (11.6 US gal, 9.68 Imp gal)
Check oil and À uid levels with dipsticks or reservoir gauges. *1 The engine coolant amount varies depending on the speci¿ cation.