2017 MAZDA MODEL 2 height adjustment

2–5
Essential Safety Equipment
Seats
*Some models.
Front Seat
Seat Operation


Seat Slide
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.

Height Adjustment *

To adjust the seat height, move the lever up or down.

Seat Recline
To change the seatback angle, lean forward slightly while raising the lever. Then lean back
to the desired position and release the lever.
Make sure the lever returns to its original position and the seatback is locked in place by
attempting to push it forward and backward.

2–11
Essential Safety Equipment
Seats
4. Make sure that the seat belt is neither
stuck in the rear seat nor twisted, then
remove the seat belt from the belt clip.

Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the
rear centre seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WARNING
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted.
In addition, always raise the head
restraints on all rear seat when they are
being used:
Driving with the head restraints
adjusted too low or removed is
dangerous. With no support behind
your head, your neck could be seriously
injured in a collision.
Height Adjustment
Adjust the head restraint so that the centre
is even with the top of the passenger's ears.



To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the stop-
catch release, then push the head restraint
down.

4–37
When Driving
Instrument Cluster and Display
Each setting/adjustment for the active driving display can be performed on the centre
display.

1. Select the icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
 

 
 Method for adjusting screen brightness (automatically/manually)


 
 Screen brightness initial settings (automatic adjustment is selected)


 
 Screen brightness adjustment (manual adjustment is selected)


 
 Display position of active driving display (display height)


 
 Active driving display angle adjustment (display angle correction)


 
 Turn by turn (TBT) display/non-display (navigation guidance)


 
 Street name display timing can be changed (navigation guidance)


 
 Active driving display ON/OFF (indication)


 
 Reset settings (reset)
NOTE
The street name may not be displayed depending on the market and region.

9–17
Speci¿ cations
Personalisation Features
Item Feature Factory Setting Available
Settings Settings Change
Method


Active Driving Display (page 4-35 )
Display Setting can be changed so that
the Active Driving Display is
not displayed. On On/Off C —


The display height (up/down
position) can be changed. 0 13 steps up/
down from initial
setting
(total: 27 steps) C —


The method for adjusting
the display brightness
(automatically/manually) can
be changed. AUTO AUTO/
MANUAL C —


The standard brightness
while automatic adjustment is
selected can be changed using
the brightness adjustment. 0 2 steps up/down
from initial
setting
(total: 5 steps) C —


The standard brightness while
manual adjustment is selected
can be changed using the
brightness adjustment. 0 20 steps up/
down from initial
setting
(total: 41 steps) C —


Navigation guidance The display information can
be changed. Adaptive Lane/
Street/Turn At Manoeuvre/
Lane Guidance
& Turn by Turn/
Street Name &
Turn by Turn/
OFF C —


*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda recommends
that these systems remain On.
*2 For vehicles with an audio system other than the on-screen function type, the warning sound cannot be changed.
The warning sound is only a beep.
*3 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation can be changed. The
volume of the warning beep during Rear Cross Traf¿ c Alert (RCTA) operation cannot be changed.
*4 If the auto-wiper control is set to Off, the wiper lever
position is set to intermittent operation.
*5 The operation may stop in 15 minutes due to the effect of the outside temperature even if the operation time of
the rear window defogger has been changed to Continuous.
*6 Available only in display from the centre display.