2017 LEXUS RX200T Owners Manual

185
3
Operation of each component
RX350/RX200t_EE_OM48F32E
3-3. Adjusting the seats
Seat position adjustment switch
Seat cushion (front) angle adjust-
ment switch
Vertical height adjustment switch
Seatback angle adjustment switch
Lumbar support firmness adjust-
ment switch
Lumbar support height adjustment
switch (if equipped)
Seat cushion length adjustment
switch (if equipped)
■Power easy access system
The driver’s seat (on some models) and steering wheel move in accordance with engine switch mode and the driver’s seat belt condition. ( P. 195)
Front seats
Adjustment procedure
1
2
3
4
5
6
7
WARNING
■When adjusting the seat position
●Take care when adjusting the seat position to ensure that other passengers are not injured by the moving seat.
●Do not put your hands under the seat or near the moving parts to avoid injury. Fingers or hands may become jammed in the seat mechanism.
●Make sure to leave enough space around the feet so they do not get stuck.
■Seat adjustment
To reduce the risk of sliding under the lap be lt during a collision, do not recline the seat more than necessary.
If the seat is too reclined, th e lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the riskof death or serious injury in the event of an accident.
Adjustments should not be made while driving as the seat may unexpectedly move and cause the driver to lose control of the vehicle.

1863-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
Manual seat
Seatback angle adjustment lever
Seat position adjustment lever
Power seat
Seatback angle adjustment switch
Seat position adjustment lever
Rear seats
Adjustment procedure
1
2
1
2

1873-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
■Before folding down the rear seatbacks
Stow the rear center seat belt and seat belt buckles.
Lower the rear seat head restraints. ( P. 200)
■Folding down the rear seatbacks (manual seat)
Rear seat lever
Pull the seatback angle adjustment
lever and fold down the rear
seatback.
Luggage compartment lever
Pull the seatback angle adjustment
lever and fold down the rear
seatback.
Folding down the rear seatbacks
1
2

1883-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
■Folding down the rear seatbacks (power seat)
Press and hold the switch to fold down the rear seatback.
A buzzer will sound and then the operation will start. The buzzer will sound again when the operation is completed.
To stop the operation partway, press either side of the rear seat operation switch of
the operating seat. Any rear seat operatio n switch for the operating seat, regard- less of location, can be used to stop the operation. (A buzzer may sound depend-ing on the position that the rear seatback is stopped.)
■Folding down the rear center seatback
Pull the lock release lever behind the
rear seatback and fold the rear
seatback down.
To return the rear center seatback to
its original position, lift it up until it locks.
Rear seat operation switch
(rear seat)
Rear seat operation switch
(luggage compartment)
When using the rear seat operation switch (rear seat): If the rear seatback is
reclined, bring the rear seatback to the most upright position and press and
hold the switch again.

1893-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
■Returning the rear seatbacks (manual seat)
Raise the rear seatback until it
locks.
Check that the plate of the seat
belt is on the front side of the seat.
1
2

1903-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
■Returning the rear seatbacks (power seat) Press and hold the switch to return the rear seatback.
A buzzer will sound and then the operation will start. The buzzer will sound again
when the operation is completed.
To stop the operation partway, press either side of the rear seat operation switch of
the operating seat. Any rear seat operation switches for the operating seat,
regardless of location, can be used to stop the operation. (A buzzer may sound
depending on the position that the rear seatback is stopped.)
Check that the plate of the seat
belt is on the front side of the seat.
1
Rear seat operation switch
(rear seat)Rear seat operation switch
(luggage compartment)
2

1913-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
■The rear seatbacks can be adjusted when (power seat)
■The rear seatbacks can be folded down when (power seat)
When all of the following conditions are met, a rear seat operation switch can be used to fold down the rear seatback:
●When using the rear seat operation switch (r ear seat): The rear door nearest to the seat
to be operated is open.
●When using the rear seat operation switch (luggage compartment): The back door is open.
●The other seat operation switch for the seat to be operated is not being pressed.
When the engine switch is in IGNITION ON mode, one of the following conditions must also be met in order for the power seat to be operated:
• The parking brake is engaged. • The brake pedal is depressed.• The shift lever is in P.
When the rear seatback is in a position within the range A shown in the illustration, the rear
seat operation switch (rear seat) can be used to adjust the rear seatback.
●When the engine switch is turned off or inACCESSORY mode
●When using the rear seat operation switch
(rear seat): The rear seatback is in a position within the range A shown in the illustration.
●When using the rear seat operation switch
(luggage compartment): The rear seatback is in a position within the range B shown in theillustration.
Most
upright
position
Most upright position

1923-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
■The rear seat seatbacks can be raised when (power seat)
When all of the following conditions are met, a rear seat operation switch can be used to return the rear seatback:
●When using the rear seat operation switch (luggage compartment): The back door is
open.
●The other seat operation switch for the seat to be operated is not being pressed.
When the engine switch is in IGNITION ON mode, one of the following conditions must
also be met in order for the power seat to be operated:
• The parking brake is engaged. • The brake pedal is depressed.
• The shift lever is in P.
■Fully reclining the rear seatback (power seat)
■Power seat operations (if equipped)
If a seat cover or seat cushion has been put on the seat, it may not operate properly. When folding down the rear seatback, make sure that there is nothing on the seat thatwould interfere with the operation.
■Rear seatback jam protection function (power seat)
When folding down or raising th e rear seatback, if an object is detected between the rear seatback and seat cushion, the rear seatb ack will stop and then move in the opposite direction slightly.
A buzzer will sound continuously when the rear seatback stops and intermittently when moving in the opposite direction.
●When the engine switch is turned off or inACCESSORY mode
●When using the rear seat operation switch(rear seat): The rear seatback is in a positionwithin the range A shown in the illustration.
●When using the rear seat operation switch(rear seat): The rear door nearest to the seat tobe operated is open.
Operate the rear seat operation switch (rear seat) to recline the rear seatback and stop itpartway. To set the rear seatback to the
rearmost position, press the button again.
Most
upright position