2017 INFINITI QX30 radio controls

pressure shown on the Tire and Loading Infor-
mation label located in the driver’s door open-
ing, seeTire and loading information label in
the 9. Maintenance and Schedules section.
The low tire pressure warning light does not
automatically turn off when the tire pressure is
adjusted. After the tire is inflated to the recom-
mended pressure, the vehicle must be driven at
speeds above 16 MPH (25 km/h) to activate the
TPMS and turn off the low tire pressure warning
light. Use a tire pressure gauge to check the tire
pressure.
The low tire pressure warning message appears
each time the ignition switch is placed in the ON
position as long as the low tire pressure warn-
ing light remains illuminated.
For additional information, see Vehicle infor-
mation display later in this section and Tire
Pressure Monitoring System (TPMS) in the
5. Starting and driving section.
TPMS malfunction
:
If the TPMS is not functioning properly, the low
tire pressure warning light will flash for approxi-
mately 1 minute when the ignition switch is
placed in the ON position. The light will remain
on after 1 minute. Have the system checked. It is
recommended that you visit an INFINITI retailer for this service. The low tire pressure warning
does not appear if the low tire pressure warning
light illuminates to indicate a TPMS malfunc-
tion.
For additional information, see
Tire Pressure
Monitoring System (TPMS) in the5. Starting
and driving section.
WARNING
•Radio waves could adversely affect electric
medical equipment. Those who use a pace-
maker should contact the electric medical
equipment manufacturer for the possible in-
fluences before use.
•If the light does not illuminate with the ig-
nition switch pushed ON, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
•If the light illuminates while driving, avoid
sudden steering maneuvers or abrupt brak-
ing, reduce vehicle speed, pull off the road
to a safe location and stop the vehicle as
soon as possible. Driving with under-
inflated tires may permanently damage the
tires and increase the likelihood of tire fail-
ure. Serious vehicle damage could occur
and may lead to an accident and could result
in serious personal injury or death. Check the tire pressure for all four tires. Adjust the
tire pressure to the recommended COLD tire
pressure shown on the tire placard, located
in the driver’s door opening, to turn the low
tire pressure warning light off. If the light
still illuminates while driving after adjust-
ing the tire pressure, a tire may be flat. If you
have a flat tire, replace it with a replacement
tire as soon as possible.
•If a replacement tire is mounted or a wheel
is replaced without a TPMS sensor tire pres-
sure will not be indicated, the TPMS will not
function and the low tire pressure warning
light will flash for approximately 1 minute.
The light will remain on after 1 minute. Have
your vehicle’s tires replaced and/or TPMS
system reset as soon as possible. It is rec-
ommended you visit an INFINITI retailer for
these services.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
CAUTION
•The TPMS is not a substitute for the regular
tire pressure check. Be sure to check the tire
pressure regularly.
2-10Instruments and controls

Lane not recommended5: you will not be able
to complete the next change of direction if you
stay in this lane.
Recommended lane and new lane during a
change of direction
3: in this lane you will be
able to complete the next two changes of
direction without changing lane.
Recommended lane
4: in this lane you will be
only able to complete the next change of direc-
tion without changing lane.
Other status indicators of the navigation system:
The navigation system displays additional infor-
mation and the vehicle status. Possible dis-
plays:
•[New route...] or [Calculating route...]
A new route is calculated.
•[Off map] or [Off road]
The vehicle position is outside of the area of
the digital map (off-map position).
•[No route]
No route could be calculated to the selected
destination.
•
You have reached the destination or an
intermediate destination.
Audio menu
Selecting a radio station:
1Frequency range
2Station frequency/name with memory po-
sition
The memory position is only displayed along
with station
2if this has been stored.
1. Switch on the audio system or navigation system and select Radio.
2. Press the
orbutton on the
steering wheel to select the [Audio] menu.
3. To select a stored station, briefly press
or.
NIC2723NIC2724
2-20Instruments and controls

4. To select a station from the station list,press and briefly hold theorbutton.
If no station list is received:
5. To elect a station using the station search: press and briefly hold the
orbutton.
NOTE
DAB radio mode (Digital Audio Broadcasting) is
an optimized digital transmission standard de-
signed for the cellular reception of radio trans-
missions. Audio player or audio media operation
:
1Current track
Audio files from various audio players or media
can be played, depending on the equipment
fitted in the vehicle.
1. Switch on the audio system or navigation system and select audio CD or MP3 mode.
2. Press the
orbutton on the
steering wheel to select the [Audio] menu.
3. To select the next/previous track, briefly press
or.
4. To select a track from the track list (rapid scrolling): press and hold the
or. button until the desired track has
been reached. If you press and hold the
orbut-
ton, the rapid scrolling speed is increased.
Not all audio players or media support this
function.
If track information is stored on the audio
player or media, the vehicle information display
will show the number and title of the track.
The current track does not appear in audio AUX
mode (Auxiliary audio mode: external audio
source connected).
NIC2839
Instruments and controls2-21

MessagePossible causes/consequences and solutions
[Check Brake Fluid Level]There is insufficient brake fluid in the brake fluid reservoir.
In addition, the redwarning light lights up in the combination meter and a warning tone sounds.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions. Do not continue driving under any circumstances.
2. Secure the vehicle against rolling away.
3. Check the brake fluid level. If brake fluid is necessary, add fluid and have the system checked. It is recommended you visit an INFINITI
retailer for this service. See Brake fluidin the8. Do-it-yourself section.
4. If the brake fluid level is correct, have the warning system checked. It is recommended you visit an INFINITI retailer for this service.
WARNING•Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive
carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.
•Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stopping distance and braking will
require greater pedal effort as well as pedal travel.
•If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been
checked. It is recommended you visit an INFINITI retailer for this service.
[Check Brake Pad Wear] The brake pads/linings have reached their wear limit.
It is recommended you visit an INFINITI retailer.
[Emergency Brake Currently
Unavailable See Operator’s
Manual] Forward Emergency Braking is temporarily inoperative.
Possible causes:
•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The system is outside the operating temperature range.•The on-board voltage is too low.
Once the causes listed above no longer apply, the display message goes out.
Forward Emergency Braking is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Restart the engine.
2-36Instruments and controls

Driving systems
MessagePossible causes/consequences and solutions
[Lane Departure Warning
Currently Unavailable See
Operator’s Manual] Lane Departure Warning is deactivated and temporarily inoperative.
Possible causes:
•The windshield is dirty in the camera’s field of vision.•Visibility is impaired due to heavy rain, snow or fog.•There have been no lane markings for an extended period.•The lane markings are worn, dark or covered, e.g. by dirt or snow.
Once the causes listed above no longer apply, the display message goes out.
Lane Departure Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Clean the windshield
[Lane Departure Warning In-
operative] Lane Departure Warning is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Blind Spot Warning Currently
Unavailable See Operator’s
Manual] Blind Spot Warning is temporarily inoperative. Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The radar sensor system is outside the operating temperature range.
The yellow indicator lights also light up in the exterior mirrors.
Once the causes listed above no longer apply, the display message goes out.
Blind Spot Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Restart the engine
[Blind Spot Warning Not Avail-
able When Towing a Trailer
See Operator’s Manual] Blind Spot Warning is deactivated while towing a trailer.
You have established the electrical connection between the trailer and your vehicle.
Press on the steering wheel to confirm the display message.
Instruments and controls2-47

MessagePossible causes/consequences and solutions
[ICC Currently Unavailable
See Operator’s Manual] Intelligent Cruise Control is temporarily inoperative.
Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The system is outside the operating temperature range.•The on-board voltage is too low.
A warning tone also sounds.
Once the causes listed above no longer apply, the display message goes out.
Intelligent Cruise Control is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Restart the engine
[ICC Inoperative] Intelligent Cruise Control is faulty. Forward Emergency Braking may also have become inoperative. A warning tone also sounds.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[ICC Suspended] You have depressed the accelerator pedal. Intelligent Cruise Control is no longer controlling the speed of the vehicle. Remove your foot from the accelerator pedal.
[ICC---MPH] An activation condition for Intelligent Cruise Control is not fulfilled.
Check the activation conditions for Intelligent Cruise Control (see Intelligent Cruise Control (ICC) system (Full speed range) (if equipped)
in the 5. Starting and driving section)
[ICC and Speed Limiter Inop-
erative] Intelligent Cruise Control and Speed Limiter are faulty.
A warning tone also sounds.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Cruise Control and Speed
Limiter Inoperative] Cruise Control and Speed Limiter are faulty.
A warning tone also sounds.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Speed Limiter Suspended] While depressing the accelerator pedal beyond the pressure point (kickdown), Speed Limiter cannot be activated. If conditions permit, drive faster than 20 MPH (30 km/h) and store the speed.
Instruments and controls2-49

REAR READING LIGHTS (IF EQUIPPED)
1Switches the left hand reading light on/
off
2Switches the right hand reading light
on/off
REAR ROOM LIGHT (IF EQUIPPED)
The rear room light (without switches) can be
switched on and off using the front overhead
control panel.
VANITY MIRROR LIGHTS
To access the vanity mirror, pull the sun visor
down and flip open the mirror cover.
The vanity mirror light illuminates when the
vanity mirror cover is opened. When the cover is
closed, the light will turn off.
LUGGAGE COMPARTMENT LIGHT
The light illuminates while the lift gate is
opened. When the lift gate is closed, the light
will turn off.
BATTERY SAVER SYSTEM
When the interior light stays on, it will auto-
matically turn off within a period of time after
the ignition switch has been turned to the OFF
position. To turn on the light again, put the
ignition switch in the ON position.The HomeLink® Universal Transceiver, inte-
grated in the vehicle’s inside rear view mirror,
provides a convenient way to consolidate the
functions of up to three individual hand-held
transmitters into one built-in device.
HomeLink® Universal Transceiver:
•Will operate most Radio Frequency (RF) de-
vices such as garage doors, gates, home and
office lighting, entry door locks and security
systems.
•Is powered by your vehicle’s battery. No
separate batteries are required. If the vehi-
cle’s battery is discharged or is discon-
nected, HomeLink® will retain all program-
ming.
When the HomeLink® Universal Transceiver is
programmed, retain the original transmitter for
future programming procedures (Example: new
vehicle purchases). Upon sale of the vehicle, the
programmed HomeLink® Universal Transceiver
buttons should be erased for security purposes.
For additional information, refer to Program-
ming HomeLink® later in this section.
NIC2632SIC3869Z
HOMELINK® UNIVERSAL TRANSCEIVER (IF
EQUIPPED)
2-86Instruments and controls

4. Position the end of your hand-held transmit-ter
52–8 inches (5–20 cm) away from the
HomeLink® surface, keeping the
HomeLink® indicator light
1in view.
5. Press and hold button
6on the hand held
transmitter until indicator lamp
1lights up
green. When indicator lamp
1: lights up
green: programing is finished.
When indicator lamp
1flashes green: pro-
graming was successful. The next step is to
synchronize the rolling code.
6. Release button
6on the hand held trans-
mitter
5for the garage door drive system.
If indicator lamp
1lights up red: repeat the
programing procedure for the corresponding
button on the rear-view mirror. When doing
so, vary the distance between the hand held
transmitter
5and the rear-view mirror.
The required distance between the hand
held transmitter
5and the integrated ga-
rage door opener depends on the garage
door drive system. Several attempts might
be necessary. You should test every position
for at least 25 seconds before trying another
position.
Synchronizing the rolling code
If the garage door system uses a rolling code,
you will also have to synchronize the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this you
will need to use the programing button on the
door drive control panel. The programing button
may be positioned at different locations de-
pending on the manufacturer. It is usually lo-
cated on the door drive unit on the garage
ceiling.
Familiarize yourself with the garage door drive
operating instructions before carrying out the
following steps.
Your vehicle must be within reach of the garage
door or gate opener drive. Make sure that
neither your vehicle nor any persons/ objects
are present within the sweep of the door or
gate.
1. Turn the ignition key to the ON position.
2. Get out of the vehicle.
3. Press the programing button on the door drive unit.
Usually, you now have 30 seconds to initiate
the next step.
4. Get into the vehicle. 5. Press previously programed button
2,3or4on the HomeLink® until the door
closes.
The rolling code synchronization is then com-
plete.
If you live in Canada
Canadian radio frequency laws require a break
(or interruption) of the transmission signals
after broadcasting for a few seconds. Therefore,
these signals may not last long enough for the
integrated garage door opener. The signal is not
recognized during programing. Comparable
with Canadian law, some U.S. garage door
openers also feature a break.
Proceed as follows:
•If you live in Canada
•If you have difficulties programing the ga-
rage door opener (regardless of where you
live) when using the programing steps.
1. Press and hold one of buttons
2to4on
the HomeLink®. After a short time, indicator
lamp
1lights up yellow.
2. Release the button. Indicator lamp
1flashes yellow.
2-88Instruments and controls