2017 INFINITI QX30 tires

CHECKING TIRE PRESSURE
1. Remove the valve stem cap from the tire.
2. Press the pressure gauge squarely onto thevalve stem. Do not press too hard or force
the valve stem sideways, or air will escape. If
the hissing sound of air escaping from the
tire is heard while checking the pressure,
reposition the gauge to eliminate this leak-
age.
3. Remove the gauge. 4. Read the tire pressure on the gauge stem
and compare it to the specification shown
on the Tire and Loading Information label.
5. Add air to the tire as needed. If too much air is added, press the core of the valve stem
briefly with the tip of the gauge stem to
release pressure. Recheck the pressure and
add or release air as needed.
6. Install the valve stem cap.
7. Check the pressure of all other tires, includ- ing the spare.
Tire Size Cold Tire Inflation Pressure
Front Rear
235/
50R18 (2WD)
35psi
(240kPa) 35psi
(240kPa)
(4WD/
AWD) 35psi
(240kPa) 29psi
(200kPa)
235/45R19 32psi
(220kPa) 32psi
(220kPa)
Spare Tire NONELDI0393

Anti-lock Braking System
(ABS) warning light
When the ignition switch is in the ON position,
the ABS warning light illuminates to indicate
that the ABS is operational. The light then turns
off within a few seconds after the engine is
started.
If the ABS light comes on while the engine is
running, it may indicate the anti-lock braking
system is not functioning properly. Have the
system checked. It is recommended that you
visit an INFINITI retailer for this service.
If the ABS warning light comes on while driving,
it may indicate the ABS is not functioning
properly. Observe the additional display mes-
sages (if any) in the vehicle information display.
Have the system checked by an INFINITI retailer.
If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system then
operates normally, but without anti-lock assis-
tance (seeBrake system in the5. Starting and
driving section).
BRAKE warning light (red)
WARNING
•Your brake system may not be working
properly if the warning light is on. Driving
could be dangerous. If you judge it to be
safe, drive carefully to the nearest service
station for repairs. Otherwise, have your ve-
hicle towed because driving it could be dan-
gerous.
•Pressing the brake pedal when the ignition
switch is not in the ON position and/or when
the brake fluid level is low may increase the
stopping distance and braking will require
greater pedal effort as well as pedal travel.
•If the brake fluid level is below the minimum
or MIN mark on the brake fluid reservoir, do
not drive until the brake system has been
checked. It is recommended that you visit
an INFINITI retailer for this service.
When the ignition switch is placed in the ON
position, the light remains illuminated and
turns off when the engine is started. If the light
illuminates at any other time, it may indicate
that the brake system is not functioning prop-
erly. If the BRAKE warning light illuminates, stop the vehicle immediately and contact an
INFINITI retailer.
This light functions for both the parking brake
and the foot brake systems.
Low tire pressure warning
light (if equipped)
Your vehicle is equipped with a Tire Pressure
Monitoring System (TPMS) that monitors the
tire pressure of all its tires.
The low tire pressure warning light warns of low
tire pressure or indicates that the TPMS is not
functioning properly.
When the ignition switch is in the ON position,
the Low tire pressure warming light illuminates
to indicate that the system is operational. The
light then tuns off within a few seconds after
the engine is started.
Low tire pressure warning
:
If the vehicle is being driven with low tire pres-
sure, the warning light will illuminate. A tire
pressure warning message also appears in the
vehicle information display.
When the low tire pressure warning light illumi-
nates, you should stop and adjust the tire pres-
sure of all 4 tires to the recommended COLD tire
Instruments and controls2-9

pressure shown on the Tire and Loading Infor-
mation label located in the driver’s door open-
ing, seeTire and loading information label in
the 9. Maintenance and Schedules section.
The low tire pressure warning light does not
automatically turn off when the tire pressure is
adjusted. After the tire is inflated to the recom-
mended pressure, the vehicle must be driven at
speeds above 16 MPH (25 km/h) to activate the
TPMS and turn off the low tire pressure warning
light. Use a tire pressure gauge to check the tire
pressure.
The low tire pressure warning message appears
each time the ignition switch is placed in the ON
position as long as the low tire pressure warn-
ing light remains illuminated.
For additional information, see Vehicle infor-
mation display later in this section and Tire
Pressure Monitoring System (TPMS) in the
5. Starting and driving section.
TPMS malfunction
:
If the TPMS is not functioning properly, the low
tire pressure warning light will flash for approxi-
mately 1 minute when the ignition switch is
placed in the ON position. The light will remain
on after 1 minute. Have the system checked. It is
recommended that you visit an INFINITI retailer for this service. The low tire pressure warning
does not appear if the low tire pressure warning
light illuminates to indicate a TPMS malfunc-
tion.
For additional information, see
Tire Pressure
Monitoring System (TPMS) in the5. Starting
and driving section.
WARNING
•Radio waves could adversely affect electric
medical equipment. Those who use a pace-
maker should contact the electric medical
equipment manufacturer for the possible in-
fluences before use.
•If the light does not illuminate with the ig-
nition switch pushed ON, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
•If the light illuminates while driving, avoid
sudden steering maneuvers or abrupt brak-
ing, reduce vehicle speed, pull off the road
to a safe location and stop the vehicle as
soon as possible. Driving with under-
inflated tires may permanently damage the
tires and increase the likelihood of tire fail-
ure. Serious vehicle damage could occur
and may lead to an accident and could result
in serious personal injury or death. Check the tire pressure for all four tires. Adjust the
tire pressure to the recommended COLD tire
pressure shown on the tire placard, located
in the driver’s door opening, to turn the low
tire pressure warning light off. If the light
still illuminates while driving after adjust-
ing the tire pressure, a tire may be flat. If you
have a flat tire, replace it with a replacement
tire as soon as possible.
•If a replacement tire is mounted or a wheel
is replaced without a TPMS sensor tire pres-
sure will not be indicated, the TPMS will not
function and the low tire pressure warning
light will flash for approximately 1 minute.
The light will remain on after 1 minute. Have
your vehicle’s tires replaced and/or TPMS
system reset as soon as possible. It is rec-
ommended you visit an INFINITI retailer for
these services.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
CAUTION
•The TPMS is not a substitute for the regular
tire pressure check. Be sure to check the tire
pressure regularly.
2-10Instruments and controls

•If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS may
not operate correctly.
•Be sure to install the specified size of tires
to all four wheels correctly.
Malfunction Indicator light (MIL)
(yellow)
When the ignition switch is turned to the ON
position, the yellow Malfunction Indicator light
illuminates. This means that the system is
operational.
If the yellow engine malfunction indicator light
lights up while the engine is running, there may
be a fault, for example:
•In the engine management
•In the fuel injection system
•In the exhaust system
•In the ignition system (for vehicles with
gasoline engines)
•In the fuel system
•In other monitored items, for example the
automatic transmission.The emission limit values may be exceeded and
the engine may be running in emergency mode.
CAUTION
Continued vehicle operation without having
the engine control system checked and re-
paired as necessary could lead to poor drive-
ability, reduced fuel economy and possible
damage to the engine control system.
Incorrect setting of the engine control system
may lead to non-compliance of local and na-
tional emission laws and regulations.
Have the vehicle checked as soon as possible. It
is recommended you visit an INFINITI retailer for
this service.
Distance warning light (if
equipped)
This light illuminates if the distance to the
vehicle in front is too small for the speed
selected.
If a warning tone also sounds, you are ap-
proaching a vehicle or stationary obstacle in
your line of travel at too high a speed. For
additional information see Forward emergency
braking (FEB) system (if equipped) in the
5. Starting and driving section.
Electric parking brake
warning light
The red indicator illuminates when the electric
parking brake is engaged.
If the red indicator light for the electric parking
brake flashes or is lit and/or the yellow warning
light for the electric parking brake is lit, observe
the additional messages displayed in the ve-
hicle information display.
For further parking brake operation information
seeParking brake in the3. Pre-driving checks
and adjustments section.
Seat belt (driver and front
passenger) warning light
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat belt
is unfastened. It will remain illuminated until
the driver and/or front passenger fastens their
seat belt. A chime will sound once the vehicle is
in motion, seeSeat belt reminder chime later
in this section. See Seat beltsin the1. Safety
— seats, seat belts and supplemental restraint
system section for precautions on seat belt
usage.
Instruments and controls2-11

doors and the lift gate, the exterior lighting
goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the button to save the setting. When the [Surround Lighting] function is
activated, the light cone and the area around
the vehicle are displayed in orange in the
vehicle information display
6. Press the button to confirm the setting.
Deactivating delayed switch-off of the exterior
lighting temporarily:
1. Before leaving the vehicle, switci the ignition switch to the OFF position.
2. Switch the ignition switch to the ON posi- tion.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the engine. Depending on your vehicle’s equipment, when
the surround lighting and delayed switch-off
exterior lighting are on, the following light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Activating/deactivating the interior lighting
delay
:
If you activate the [Interior Lighting Delay] func-
tion, the interior lighting remains on for 20
seconds after you remove the key from the
ignition lock.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Interior Lighting Delay] function. If the
[Interior lighting delayed switch-off] function
has been switched on, the vehicle interior is
displayed in orange in the vehicle informa-
tion display 5. Press the button to save the setting.
Vehicle
Setting permanent speed limiter:
You can set permanent speed limiter using the
[Limit Speed (Winter Tires)] function.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Vehicle] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Limit Speed (Winter Tires)] function.
You will see the selected setting.
5. Press to confirm.
6. Press the
orbutton to adjust
permanent speed limiter in increments of
ten ([150 mph] to [100 mph]), 240 km/h] to
[160 km/h]). The [Off] setting switches per-
manent speed limiter off).
7. Press the or
button to store the
entry.
Instruments and controls2-27

5. Press the button to confirm the selec-tion.
If you have selected [Yes], the vehicle infor-
mation display shows a confirmation mes-
sage.
For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must
switch the ignition switch to the ACC position.
DISPLAY MESSAGES
Display messages appear in the vehicle infor-
mation display.
Display messages with graphic symbols are
simplified in the Owner’s Manual and may differ
from the symbols in the vehicle information
display.
Certain display messages are accompanied by
an audible warning tone or a continuous tone.
When the ignition is switched off, all display
messages are deleted apart from some high-
priority display messages. Once the causes of
the high-priority display messages have been rectified, these display messages are deleted
as well.
When you stop and park the vehicle, please
observe the notes on parking (see
Parkingin
the 5. Starting and driving section).
Hiding display messages
Press the orbutton to hide the
display message. The display message is hid-
den.
The vehicle information display shows high-
priority display messages in red. Some high-
priority display messages cannot be hidden.
The vehicle information display shows these
messages continuously until the causes for the
messages have been remedied.
Message memory
The vehicle information display saves certain
messages in the message memory. You can call
up these display messages:
1. Press the
orbutton on the
steering wheel to select the [Service] menu.
If there are display messages, the vehicle
information display shows [2 messages], for
example. 2. Press the
orbutton to select the
entry, e.g. [2 messages].
3. Press to confirm.
4. Press the
orbutton to scroll
through the display messages.
Instruments and controls2-29

Tires
MessagePossible causes/consequences and solutions
[Please Correct Tire Pressure] The tire pressure is too low in at least one of the tires, or the tire pressure difference between the wheels is too great. 1. Check the tire pressures at the next opportunity (see Wheels and tiresin the8. Do-it-yourself section)
2. If necessary, correct the tire pressure.
3. Restart the tire pressure monitoring system (see Restarting TPMSin the5. Starting and driving section)
[Check Tire(s)] The tire pressure in one or more tires has dropped significantly The wheel position is displayed in the vehicle information display
A warning tone also sounds.
WARNING
Underinflated tires pose the following risks:•The tires may burst, especially as the load and vehicle speed increase.•The tires may wear excessively and/or unevenly, which may greatly impair tire traction.•The driving characteristics, as well as steering and braking, may be greatly impaired.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (see Flat tirein the6. In case of emergency section).
4. Check the tire pressures and, if necessary, correct the tire pressure.
[Warning Tire Malfunction] The tire pressure in one or more tires has dropped suddenly. The wheel position is displayed in the vehicle information display.
WARNING
If you drive with a flat tire, there is a risk of the following hazards:•A flat tire affects the ability to steer or brake the vehicle.•You could lose control of the vehicle.•Continued driving with a flat tire will cause excessive heat buildup and possibly a fire.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (see Flat tirein the6. In case of emergency section).
Instruments and controls2-51

Backing up near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown further than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as the position
A. The vehicle may hit the object
when backing up to the position
Aif the object
projects over the actual moving course.
HOW TO PARK WITH PREDICTED
COURSE LINES
WARNING
•If the tires are replaced with different sized
tires, the predicted course line may not be
displayed correctly.
•On a snow-covered or slippery road, there
may be a difference between the predicted
course line and the actual course line.
•The displayed lines will appear slightly off
to the right because the rear view camera is
not installed in the rear center of the ve-
hicle.
•If the battery is disconnected or becomes
discharged, the predicted course lines may
be displayed incorrectly. If this occurs,
please perform the following procedures: – Turn the steering wheel from lock to lock
while the engine is running.
– Drive the vehicle on a straight road for
more than 5 minutes.
SAA1923SAA1980
Display screen, heater and air conditioner, and audio system4-19