2017 INFINITI QX30 seats

MessagePossible causes/consequences and solutions
[Emergency Brake
Inoperative] Forward Emergency Braking is temporarily inoperative due to a malfunction.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Radar Sensor (See
Operator’s Manual):] At least one of the following driving systems or driving safety systems is temporarily restricted or inoperative:
•Forward Emergency Braking•Intelligent Cruise Control
Possible causes:
•The sensors in the radiator trim and/or in the bumpers are dirty.•The function of the driving system and/or driving safety system is impaired due to heavy rain or snow.
A warning tone also sounds.
Once the causes listed above no longer apply, the display message goes out. All driving systems/driving safety systems are operative
again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions
2. Secure the vehicle against rolling away.
3. Switch off the engine.
4. Clean the sensors in the following locations: - In the radiator trim
- In the front bumper
- In the rear bumper, particularly in the middle of the rear bumper.
5. Restart the engine. The display message disappears.
[SRS Malfunction Service Re-
quired] The restraint system needs servicing. Thewarning light also lights up in the combination meter.
It is recommended you visit an INFINITI retailer for these services.
Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioner seat belt may not function properly.
WARNING
If this light is on, it could mean that the front air bag, side air bag, curtain air bag systems and/or pretensioner systems will not operate in
an accident. To help avoid injury to yourself or others, have your vehicle checked as soon as possible. It is recommended you visit an INFINITI
retailer for this service.
For further information about the restraint system, see Supplemental Restraint System (SRS)in the1. Safety — seats, seat belts and
supplemental restraint system section.
Instruments and controls2-37

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Disabled See Operator’s
Manual] The front-passenger front air bag is disabled during the journey although an adult or person of corresponding stature is on the front
passenger seat.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the
front passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her
weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position),
this could cause the sensor to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for the most effective
protection by the seat belt and supplemental air bag.
If additional forces are applied to the seat, the system may interpret the occupant’s weight as lower than it actually is.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Have the occupant on the front-passenger seat step out of the vehicle.
5. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
6. Observe the indicator lights in the center console and the vehicle information display and check the following.
Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator lights must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section)
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
2-38Instruments and controls

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Enabled See Operator’s
Manual] The front-passenger front air bag is enabled during the journey although:
•A child or child restraint as specified in U.S. regulations is located on the front-passenger seat.
or
•The front-passenger seat is not occupied.
The system may detect objects or forces that are adding to the weight applied to the seat.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Open the front-passenger door.
5. Remove the child and the child restraint system from the front passenger seat.
6. Make sure there are no objects applying additional force to the seat. The system may otherwise detect the additional force and interpret the seat occupant’s weight as greater than it actually is.
7. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
8. Observe the indicator lights in the center console and the vehicle information display and check the following. Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator light must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section).
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
Instruments and controls2-39

•If any malfunctions are found or the heated
seat does not operate, turn the switch off
and have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service.The front seats are warmed by built-in heaters.
The switches are located on the center console
and can be operated independently, for the
left-hand side seat and for the right-hand side
seat.
The three red indicator lights in the button
indicate the heating level you have selected The
system automatically switches from level 3 to
level 2 after approximately eight minutes The
system automatically switches from level 2 to
level 1 after approximately ten minutes. The
system automatically switches off approxi-
mately 20 minutes after it is set to level 1. 1. Turn the ignition switch to the ON position.
NOTE
The seat heater can only be activated when
the ignition switch is in the ON position.
2. Start the engine.
3. Select the heat range:
•To switch on: press button1repeatedly
until the desired heating level is set.
•To switch off: press button1repeatedly
until all the indicator lights turn off.
NOTE
If the battery voltage is too low, the seat heating
may switch off.NIC2634
Instruments and controls2-71

•Never allow anyone to ride in the cargo area
or on the rear seat when it is in the fold-
down position. Use of these areas by pas-
sengers without proper restraints could re-
sult in serious injury or death in an accident
or sudden stop.
•Do not allow people to ride in any area of
your vehicle that is not equipped with seats
and seat belts.
•The child restraint top tether strap may be
damaged by contact with items in the cargo
area. Secure any items in the cargo area.
Your child could be seriously injured or
killed in a collision if the top tether strap is
damaged.
•Be sure everyone in your vehicle is in a seat
and using a seat belt properly.
CAUTION
•Do not apply a total load of more than 22 lb
(10 kg) to a single eyelet.
•Secure the load using the cargo tie-down
hooks.
•Distribute the load on the cargo tie-down
hooks evenly.
•Do not use elastic straps or nets to secure a
load. These are only intended as anti-slip
protection for light loads.
•Do not route tie-down ropes or straps across
sharp edges or corners.
•Pad sharp edges for protection.
LUGGAGE HOOKS
The luggage hooks1are for shopping bags,
etc.
CAUTION
•Do not apply a total load of more than 7 lb
(3 kg) to the hook.
•Do not use luggage hooks to secure a load.
NIC2671
Instruments and controls2-81

•Properly secure cargo and do not allow it to
contact the top tether strap when it is at-
tached to the top tether anchor. Cargo that
is not properly secured or cargo that con-
tacts the top tether strap may damage the
top tether strap during a collision. If the
cargo cover contacts the top tether strap
when it is attached to the top tether anchor,
remove the cargo cover from the vehicle or
secure it on the cargo floor below its attach-
ment location. If the cargo cover is not re-
moved, it may damage the top tether strap
during a collision. Your child could be seri-
ously injured or killed in a collision if the
child restraint top tether strap is damaged.
•Do not use the cargo cover if the rear seats
are folded down.
Removal
1. Open the lift gate (seeLift gate lockin the
2. Instruments and controls section).
2. Detach both of the cords (left and right)
1from the inside of the lift gate.
3. Detach the parcel shelf
2by simply pulling
it rearwards through the lift gate opening.
CAUTION
Make sure the parcel shelf is carefully stored
when not in use in order to prevent any
damage.
Installation
1. Open the lift gate.
2. Insert the parcel shelf by pushing it forwards as far as possible through the lift gate
opening.
3. Attach the corresponding cords to each side
1of the lift gate.
4. Close the lift gate (see Lift gate lockin the
2. Instruments and controls section).
ROOF RACK (IF EQUIPPED)
Genuine NISSAN accessory cross bars are avail-
able through an INFINITI retailer. It is recom-
mended you visit an INFINITI retailer for cross-
bar or other equipment information.
Always distribute the luggage evenly on the roof
rack. Observe the maximum load limit shown on
the crossbars or roof carriers when you attach
them on the roof rails. It is recommended you
visit an INFINITI retailer for cross bar or other
equipment information.
Do not apply any load directly to the roof side
rails. Cross bars (if so equipped) must be
installed before applying load/cargo/luggage
to the roof of the vehicle.
Be careful that your vehicle does not exceed the
Gross Vehicle Weight Rating (GVWR) or its Gross
Axle Weight Rating (GAWR front and rear). The
GVWR and GAWR are located on the F.M.V.S.S.
or C.V. M.S.S. certification label (located on the
driver’s door pillar). For additional information,
refer toVehicle loading information in the10.
Technical information section.
NIC2672
Instruments and controls2-83

seat. If someone becomes trapped, immedi-
ately release the memory function position
button The adjustment is stopped.
•If children activate the memory function,
they could become trapped, especially if
they are unattended. There is a risk of in-
jury.
When leaving the vehicle, always take the
key with you and lock the vehicle. Never
leave children unattended in the vehicle.
The memory function can be used at any time,
e.g. even when the key isn’t in the ignition lock.
STORING SETTINGS
With the memory function, you can store up to
three different settings.
•Seat and seatback position
•Driver’s side: position of the exterior mirrors
on the driver’s and front-passenger sides.
To store settings:
1. Adjust the seat (see Power seat adjustment
in the 1. Safety — seats, seat belts and
supplemental restraint system section).
2. Adjust the exterior mirror on the driver’s side (see Adjusting in the3. Pre-driving checks
and adjustments section).
3. Briefly press the M memory button
1, and
then press preset position button 1, 2 or 3
2within three seconds.
The settings are stored in the selected pre-
set position. A tone sounds when the set-
tings have been completed.
CALLING UP A STORED SETTING
Press and hold the relevant preset position
button 1, 2 or 3 until the seat and exterior
mirrors are in the stored position.
NOTE
The setting procedure is interrupted as soon as
you release the storage position button.
Pre-driving checks and adjustments3-21

– CDs with a paper label
– CDs that are warped, scratched, or haveabnormal edges
•This audio system can only play prerecorded
CDs. It has no capabilities to record or burn
CDs.
•If a CD cannot be played, one of the following
messages will be displayed.
[Disc Reading Error]
Indicates a CLV/Focus, TOC or Access error.
Check and re-insert the CD. Make sure that it
is inserted correctly.
[Please Eject Disc]
Indicates a mechanism error. If the CD can be
ejected, eject and re-insert the CD. If the CD
cannot be ejected, have the system checked.
It if recommended you contact an INFINITI
retailer for this service.
[File type is not supported]
Indicates that no readable files are found on
the inserted CD. Check the data on your CD.
USB (Universal Serial Bus) connection
port/ iPod
The Media Hub is located in the center console
and consists of the USB connectors. 1) USB/iPod connection port
Connect to play media from an iPod
R,
iPhone
Ror a USB memory device. When
using INFINITI InTouch Apps with an
iPhone
R, connect via a USB cable. Refer to
the device manufacturer’s owner information
regarding the proper use and care of the
device.
WARNING
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION
•Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is con-
nected correctly into the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
•Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
The vehicle is not equipped with a USB device.
USB devices should be purchased separately as
necessary.
This system cannot be used to format USB
devices. To format a USB device, use a personal
computer.
In some areas, the USB device for the front
seats plays only sound without images for
regulatory reasons, even when the vehicle is
parked.
This system supports various USB memory de-
vices, USB hard drives and iPod players. Some
NAA1628
4-56Display screen, heater and air conditioner, and audio system