2017 INFINITI QX30 key

Symptom Possible causeRemedy
The engine
cannot be
started using
the key The on-board
voltage is too
low
•Switch off non-essential consumers, e. g. seat heating or interior lighting, and try to start the engine again
If this does not work:
•Check the starter battery and charge it if necessary (see Batteryin the8. Do-it-yourself section)
or
•Jump-start the vehicle (see Jump startingin the6. In case of emergency section)
or
•Have the system checked. It is recommended you consult an INFINITI retailer.
You have lost
a key —
•Have the key deactivated. It is recommended you visit an INFINITI retailer for this service.•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well
You have lost
the emer-
gency key ele-
ment
•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well.
Pre-driving checks and adjustments3-13

4. Insert the support rod3into the slot4on
the underside of the hood.
5. When closing the hood, replace the support rod in its original position
5, slowly lower
the hood to about8–12in.(20–30cm)
above the hood lock, then let it drop. Make
sure the hood is securely latched.
WARNING
•Make sure the hood is completely closed
and latched before driving. Failure to do so
could cause the hood to fly open and result
in an accident.
•If you see steam or smoke coming from the
engine compartment, to avoid injury do not
open the hood.
OPENING FUEL-FILLER DOOR
To open the fuel-filler door, unlock it using one
of the following operations, then push the right
side of the door
1.
•Push the door handle request switch with the
Intelligent Key carried with you.
•Push the “UNLOCK”button on the
Intelligent Key.
•Push the power door lock switch to the
“UNLOCK”position.
To close the fuel-filler door, close the door until
it securely latches. To lock the fuel filler door,
lock the vehicle using the intelligent key.
FUEL-FILLER CAP
Turn the fuel-filler cap counterclockwise to re-
move. To tighten, turn the cap clockwise until a
single click is heard.
Put the fuel-filler cap on the cap holder
2while refueling.
WARNING
•Gasoline is extremely flammable and highly
explosive under certain conditions. You
could be burned or seriously injured if it is
misused or mishandled. Always stop the en-
gine and do not smoke or allow open flames
or sparks near the vehicle when refueling.
•Do not attempt to top off the fuel tank after
the fuel pump nozzle shuts off automati-
cally. Continued refueling may cause fuel
overflow, resulting in fuel spray and possi-
bly a fire.
•Use only an original equipment type fuel-
filler cap as a replacement. It has a built-in
safety valve needed for proper operation of
the fuel system and emission control sys-
tem. An incorrect cap can result in a serious
malfunction and possible injury.
•Never pour fuel into the throttle body to
attempt to start your vehicle.
NDI1605NPA1482
FUEL-FILLER DOOR
Pre-driving checks and adjustments3-15

seat. If someone becomes trapped, immedi-
ately release the memory function position
button The adjustment is stopped.
•If children activate the memory function,
they could become trapped, especially if
they are unattended. There is a risk of in-
jury.
When leaving the vehicle, always take the
key with you and lock the vehicle. Never
leave children unattended in the vehicle.
The memory function can be used at any time,
e.g. even when the key isn’t in the ignition lock.
STORING SETTINGS
With the memory function, you can store up to
three different settings.
•Seat and seatback position
•Driver’s side: position of the exterior mirrors
on the driver’s and front-passenger sides.
To store settings:
1. Adjust the seat (see Power seat adjustment
in the 1. Safety — seats, seat belts and
supplemental restraint system section).
2. Adjust the exterior mirror on the driver’s side (see Adjusting in the3. Pre-driving checks
and adjustments section).
3. Briefly press the M memory button
1, and
then press preset position button 1, 2 or 3
2within three seconds.
The settings are stored in the selected pre-
set position. A tone sounds when the set-
tings have been completed.
CALLING UP A STORED SETTING
Press and hold the relevant preset position
button 1, 2 or 3 until the seat and exterior
mirrors are in the stored position.
NOTE
The setting procedure is interrupted as soon as
you release the storage position button.
Pre-driving checks and adjustments3-21

•Touch
Select and execute the selected key on the
screen.
•Swipe
Menu screen pages will skip to the next page.
•Drag
Drag the scroll bar up or down to scroll the
menu screen.
NAA1783
NAA1707
NAA1724
4-6Display screen, heater and air conditioner, and audio system

Touch adjustment keys, such as [+]/[-], [L]/[R],
etc., to adjust each item. Each time a key is
touched, the indicator moves along the bar.
HOW TO INPUT LETTERS AND
NUMBERS
The keyboard screen differs depending on the
model and specification.
Character (letters and numbers) input
screen
Alphanumeric characters can be entered using
the keyboard.
The designs and the displayed items may vary
depending on the type of screen.
1Touch a character on the displayed key-
board. The selected character is entered.
2Entered characters are displayed.
3Touch [Delete] to delete the last character
entered.
Touch and hold [Delete] to delete all the
characters entered.
4The symbol keys are displayed by touch-
ing [Symbols]. The alphabet keys are dis-
played by touching [A-Z].
5Touch [Space] to enter a space.
6Touchorto move the cursor.
7Touch [CAPS] to toggle between upper
and lower case letters.
HOW TO OPERATE DISPLAY
Touch screen display
To operate the display, touch the display di-
rectly or use the INFINITI controller.
Shortcut menu
Models with navigation system:
The shortcut menu can be displayed on the
display. The display may differ depending on
the conditions of the current map screen.
NAA1730NAA1710NAA1711
4-8Display screen, heater and air conditioner, and audio system

A[Settings] key
B

A[Settings] key
B

SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolor-
ation. To clean the camera, wipe with a cloth
dampened with diluted mild cleaning agent
and then wipe with a dry cloth.
•Do not damage the camera as the monitor
screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras, the Around View Monitor may not
display objects clearly. Clean the cameras by
wiping with a cloth dampened with a diluted
mild cleaning agent and then wiping with a dry
cloth.
A[Settings] key
B