2017 INFINITI QX30 lane assist

Video DVD operation (outside Europe only):
It is only possible to use the [Audio] menu to
operate video DVDs on vehicles with navigation
system.
1. Switch on the audio system or navigationsystem and select video DVD.
2. Press the
orbutton on the
steering wheel to select the [Audio] menu.
3. To select the next or previous scene, briefly press
or.
4. To select a scene from the scene list (rapid scrolling): press and hold the
or. button until the desired scene1has
been reached.
Assistance menu
Depending on the equipment fitted in the ve-
hicle, you have the following options in the
[DriveAssist] menu:
•Showing the assistance graphic
•Activating/deactivating VDC
•Activating/deactivating Forward Emergency
Braking (FEB)
•Activating/deactivating Blind Spot Warning
(BSW)
•Activating/deactivating Lane Departure
Warning (LDW) Showing the distance display
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Distance display].
3. Press the button. The vehicle information display shows the
Intelligent Cruise Control (ICC) distance dis-
play in the assistance graphic.
The distance display also shows you the
status of and/or information from the follow-
ing driving systems or driving safety sys-
tems:
•Intelligent Cruise Control (ICC)
•Forward Emergency Braking (FEB)
NIC2726NIC2873NIC2729
2-22Instruments and controls

•Lane Departure Warning (LDW)
•Blind Spot Warning (BSW)
•Rear window wiper
Deactivating/activating VDC
:
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor.
If maximum engine power is needed to free a
stuck vehicle, turn the VDC system off.
For further information about VDC, see Vehicle
Dynamic Control (VDC) system in the
5. Starting and driving section.
1. Start the engine.
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
3. Press the
orbutton to select
[ESP]. 4. Press the button.
The current selection is displayed.
5. To activate/deactivate: press the button again.
VDC is deactivated if the
warning light
in the combination meter lights up continu-
ously when the engine is running.
If both the
warning light andwarning light are lit continuously, VDC is not
available due to a malfunction.
Activating/deactivating Forward Emergency
Braking
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the button. The current selection is displayed.
4. To activate/deactivate: press the but- ton again.
When Forward Emergency Braking is deacti-
vated, the
symbol appears in the
vehicle information display in the assistance
graphic display. For further information about Forward Emer-
gency Braking, see
Forward emergency brak-
ing (FEB) system (if equipped) in the
5. Starting and driving section.
Activating/deactivating Blind Spot Warning
(BSW)
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Blind Spot Warning].
3. Press the button. The current selection is displayed.
4. To activate/deactivate: press the but- ton again.
For further information about Blind Spot Warn-
ing, see Blind Spot Warning (BSW) system (if
equipped) in the5. Starting and driving sec-
tion.
Activating/deactivating Lane Departure Warn-
ing (LDW)
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu on the Menu bar.
Instruments and controls2-23

COMBINATION SWITCH
1Turn signal, right
2Turn signal, left
3High beam headlights
4Headlight flasher
Turn signal
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signal cancels automatically.
Lane change signal
Move the lever up or down until the turn signal
begins to flash, but the lever does not latch, to
signal a lane change. Hold the lever until the
lane change is completed. Move the lever up or
down until the turn signal begins to flash, but
the lever does not latch, and release the lever.
The turn signal will automatically flash threetimes. Choose the appropriate method to signal
a lane change based on road and traffic condi-
tions.
High beam headlights
To switch on the high beam headlights:
•Turn the ignition switch to the ON position or
start the engine.
•Turn the light switch toor
.
•Press the combination switch beyond the
pressure point in the direction of arrow
3.
In the position, the high beam head-
lights are only switched on when it is dark
and the engine is running.
The blue
indicator light in the combi-
nation meter lights up when the high beam
headlights are switched on.
To switch off the high beam headlights:
•Move the combination switch back to its
normal position. The blueindicator
light in the combination meter goes out.
NOTE
Vehicles with High beam Assist: when High
beam Assist is active, it controls activation and
deactivation of the high beam headlights (see
 High beam assist (LED headlight only) later in
this section)
ADAPTIVE FRONT LIGHTING SYSTEM
(LED HEADLIGHT ONLY) (IF EQUIPPED)
The Adaptive Front Lighting System is a system
that adjusts the headlights automatically to suit
the prevailing driving and weather conditions. It
offers advanced functions for improved illumi-
nation of the road surface, e.g. depending on
the vehicle speed or weather conditions. The
system includes the active light function, cor-
nering light function and freeway mode. The
system is only active when it is dark.
You can activate or deactivate the “Adaptive
Front Lighting System” function using the ve-
hicle information display (see Switching the
Adaptive Front Lighting System on/off earlier in
this section)
NIC2618
Instruments and controls2-65

HOW TO ENABLE/DISABLE THE LDW
SYSTEM
1. Press theorbutton on the
steering wheel
1to select the [DriveAssist]
menu on the Menu bar
B.
2. Press the
orbutton to select
[Lane Departure Warning].
3. Press the button on the steering wheel
1. The current selection is displayed.
4. Press the to confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press the button to save the setting.
When the LDW is activated, the vehicle
information display shows the lane mark- ings as bright lines in the assistance graphic
in the display area
A
When [Standard] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In this
event, the warnings are suppressed for a
certain period of time.
•A driving safety system intervenes, such as
ABS, brake assist system (BAS) or VDC.
When [Adaptive] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In this
case the warnings are suppressed for a
certain period of time.
•A driving system intervenes, such as ABS,
BAS or VDC.
•You accelerate forcefully.
•You brake forcefully.
•You steer actively, for example, swerve to
avoid an obstacle or change lane quickly.
•You cut the corner on a sharp bend.
The system may detect certain conditions and
warns you accordingly. The warning vibration occurs earlier if:
•You approach the outer lane marking on a
bend.
•The road has very wide lanes, for example, a
freeway.
•The system detects solid lane markings.
The warning vibration occurs later if:
•The road has narrow lanes.
•You cut across a corner on a bend.
LDW SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
LDW system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only a warning device to in-
form the driver of a potential unintended
lane departure. It will not steer the vehicle
or prevent loss of control. It is the driver’s
responsibility to stay alert, drive safely,
keep the vehicle in the traveling lane, and
be in control of the vehicle at all times.
NSD599Assistance graphic
Starting and driving5-31

Approach warning
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that vehicle
or if another vehicle cuts in, the system warns
the driver with the chime and distance warning
light. Decelerate by depressing the brake pedal
to maintain a safe vehicle distance if:
•The chime sounds.
•The distance warning light is illuminated.
The warning chime may not sound and the
distance warning light may not illuminate in
some cases when there is a short distance
between vehicles. Some examples are:
•When the vehicles are traveling at the same
speed and the distance between vehicles is
not changing. In this case, the distance
warning light will be on.
•When the vehicle ahead is traveling faster
and the distance between vehicles is increas-
ing.
•When a vehicle cuts in near your vehicle
•The warning chime will not sound and the
distance warning light will not illuminate
when: – The vehicle approaches other vehicles that are parked or moving slowly. – The accelerator pedal is depressed, over-
riding the system.
Also, the sensor sensitivity can be affected by
vehicle operation (steering maneuver or driving
position in the lane) or traffic or vehicle condi-
tion (for example, if a vehicle is being driven
with some damage).
Automatic cancellation
A chime sounds and the message [ICC off] is
displayed in the vehicle information display for
5 seconds under the following conditions and
the control is automatically canceled.
•The electric parking brake is applied.
•The VDC intervenes or the VDC is deacti-
vated.
•The P (Park), R (Reverse) or N (Neutral)
position is engaged.
•The cruise control lever is pulled in order to
pull away but the front passenger door or
one of the rear doors is open.
•The vehicle is skidding or a wheel slips.
•Active Park Assist is activated.
ICC LIMITATIONS
WARNING
Listed below are the system limitations for the
ICC system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only an aid to assist the
driver and is not a collision warning or
avoidance device. It is the driver’s responsi-
bility to stay alert, drive safely and be in
control of the vehicle at all times.
•The system is primarily intended for use on
straight, dry, open roads with light traffic. It
is not advisable to use the system in city
traffic or congested areas.
•This system will not adapt automatically to
road conditions. This system should be
used in evenly flowing traffic. Do not use the
system on roads with sharp curves, or on icy
roads, in heavy rain or in fog.
•As there is a performance limit to the dis-
tance control function, never rely solely on
the ICC system. This system does not cor-
rect careless, inattentive or absent-minded
driving, or overcome poor visibility in rain,
fog, or other bad weather. Decelerate the
vehicle speed by depressing the brake
5-54Starting and driving

SYSTEM MAINTENANCE
The sensor for the ICC systemAis located
behind the INFINITI logo at the front of the
vehicle.
To keep the ICC system operating properly, be
sure to observe the following:
•Always keep area around the sensor clean.
•Do not strike or damage the areas around the
sensor. Do not touch or remove the screw
located on the sensor. Doing so could cause
failure or malfunction. If the sensor is dam-
aged due to an accident, it is recommended
you contact an INFINITI retailer.
•Do not cover or attach stickers (including
transparent material) or install an accessory
near the sensor. This could cause failure or
malfunction.
Radio frequency statement
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.
WARNING
Failure to follow the warnings and instructions
for proper use of the FEB system could result in
serious personal injury or death.
•The FEB system is a supplemental aid to the
driver. It is not a replacement for the driver’s
attention to traffic conditions or responsi-
bility to drive safely. It cannot prevent acci-
dents due to carelessness or dangerous
driving techniques.
•The FEB system does not function in all driv-
ing, traffic, weather and road conditions.
The FEB system can assist the driver when there
is a risk of a forward collision with the vehicle
ahead in the traveling lane.
NSD645
FORWARD EMERGENCY BRAKING (FEB)
SYSTEM (IF EQUIPPED)
5-60Starting and driving

ACTIVE SOUND ENHANCEMENT
The active sound enhancement generates
sounds according to engine speed through the
speakers
2and woofer1(if equipped) to
enhance the quality of the engine sound. IPA is an electronic parking aid with ultrasound.
It detects vehicles and open spaces on both
sides of the vehicle. A parking symbol indicates
a suitable parking space. Active steering inter-
vention can assist you during parking and when
exiting a parking space. The driver controls the
accelerator, brake and gear shift. You may also
use the parking sensor system (see
Parking
sensor system (if equipped) later in this sec-
tion).
IMPORTANT SAFETY NOTES
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure
•This system is not designed to prevent con-
tact with small or moving objects.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
•This system is not designed to prevent con-
tact with small or moving objects.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
CAUTION
Do not drive over obstacles such as curbs, as
you may damage the wheels or tires.
IPA may also display spaces not suitable for
parking, for example:
•Parking or stopping prohibition.
INTELLIGENT PARKING ASSIST (IPA) (IF
EQUIPPED)
5-68Starting and driving

•The border of the parking space must not be
too wide, as the position of the vehicle must
not exceed an angle of 45 degrees to the
starting position as it is manoeuvred into the
parking space.
•A total front and back maneuvering distance
of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel to
the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range.
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction you are pulling away.
4. Vehicles with automatic transmission: shift
the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press the button on the steering wheel The Park
Assist [Observe surroundings] message ap-
pears in the display.
7. Release the steering wheel.
8.
Pull away, being ready to brake at all times Do
not exceed a maximum speed of approxi-
mately 5 MPH (10 km/h) when exiting a park-
ing space. Otherwise, IPA will be canceled.
WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required, shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] message
appears in the display.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
If you back up after activation, the steering
wheel is moved to the straight-ahead posi-
tion.
10. Drive forward and back up as prompted by the parking sensor system warning dis-
plays, several times if necessary.
Once you have exited the parking space com-
pletely, the steering wheel is moved to the
straight-ahead position. You hear a tone and
the [Park Assist switched off] message appears
in the display. You will then have to steer and
5-72Starting and driving