2017 INFINITI QX30 ESP

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Disabled See Operator’s
Manual] The front-passenger front air bag is disabled during the journey although an adult or person of corresponding stature is on the front
passenger seat.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the
front passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her
weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position),
this could cause the sensor to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for the most effective
protection by the seat belt and supplemental air bag.
If additional forces are applied to the seat, the system may interpret the occupant’s weight as lower than it actually is.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Have the occupant on the front-passenger seat step out of the vehicle.
5. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
6. Observe the indicator lights in the center console and the vehicle information display and check the following.
Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator lights must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section)
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
2-38Instruments and controls

Lights
NOTE
Vehicles with LEDs in the light clusters: The display message for the corresponding light will only appear if all the LEDs have failed.
MessagePossible causes/consequences and solutions
[Check Left Cornering Light] or
[Check Right Cornering Light] The left or right-hand cornering light is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Left Low Beam] or [Check
Right Low Beam]The left or right-hand low beam headlight is faulty.•Check whether you are permitted to replace the bulb yourself (see
Lightsin the8. Do-it-yourself section).
or:
•Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Rear Left Turn Signal] or
[Check Rear Right Turn Signal] The rear left or right-hand turn signal is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Front Left Turn Signal] or
[Check Front Right Turn Signal]The front left or right-hand turn signal is faulty.•Check whether you are permitted to replace the bulb yourself (see
Lightsin the8. Do-it-yourself section).
or:
•Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Left Mirror Turn Signal]
or [Check Right Mirror Turn Sig-
nal] The turn signal in the left-hand or right-hand exterior mirror is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Center Brake Lamp]
The third brake light is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
2-40Instruments and controls

Tires
MessagePossible causes/consequences and solutions
[Please Correct Tire Pressure] The tire pressure is too low in at least one of the tires, or the tire pressure difference between the wheels is too great. 1. Check the tire pressures at the next opportunity (see Wheels and tiresin the8. Do-it-yourself section)
2. If necessary, correct the tire pressure.
3. Restart the tire pressure monitoring system (see Restarting TPMSin the5. Starting and driving section)
[Check Tire(s)] The tire pressure in one or more tires has dropped significantly The wheel position is displayed in the vehicle information display
A warning tone also sounds.
WARNING
Underinflated tires pose the following risks:•The tires may burst, especially as the load and vehicle speed increase.•The tires may wear excessively and/or unevenly, which may greatly impair tire traction.•The driving characteristics, as well as steering and braking, may be greatly impaired.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (see Flat tirein the6. In case of emergency section).
4. Check the tire pressures and, if necessary, correct the tire pressure.
[Warning Tire Malfunction] The tire pressure in one or more tires has dropped suddenly. The wheel position is displayed in the vehicle information display.
WARNING
If you drive with a flat tire, there is a risk of the following hazards:•A flat tire affects the ability to steer or brake the vehicle.•You could lose control of the vehicle.•Continued driving with a flat tire will cause excessive heat buildup and possibly a fire.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (see Flat tirein the6. In case of emergency section).
Instruments and controls2-51

IMMOBILISER
The immobiliser prevents your vehicle from
being started without the correct key.
•To activate with the key: remove the key from
the ignition lock.
•To deactivate:switch on the ignition.
When leaving the vehicle, always take the key
with you and lock the vehicle. Anyone can start
the engine if a valid key has been left inside the
vehicle.
NOTE
The immobiliser is always deactivated when you
start the engine.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation. NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
ANTI-THEFT ALARM SYSTEM (IF
EQUIPPED)
To arm:
lock the vehicle with the key or Intelli-
gent key. Indicator lamp
1flashes. The alarm
system is armed after approximately 15 sec-
onds.
To deactivate: unlock the vehicle with the key or
intelligent key.
or
Insert the key into the ignition switch.
A visual and audible alarm is triggered if the
alarm system is armed and you open:
•A door.
•The vehicle with the emergency key element.
NIC2750
SECURITY SYSTEM
2-58Instruments and controls

SWITCHING THE REAR WINDOW WIPER
ON/OFF
WARNING
In freezing temperatures the washer solution
may freeze on the windshield and obscure your
vision which may lead to an accident. Warm
the windshield with the defroster before you
wash the windshield.
CAUTION
•Do not operate the washer continuously for
more than 30 seconds.
•Do not operate the washer if the window
washer fluid reservoir is empty.
•Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the
window washer reservoir tank.
•Pre-mix washer fluid concentrates with wa-
ter to the manufacturer’s recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the
washer fluid concentrate and water.
1Switch
2Wipes with washer fluid
3Switches on intermittent wiping
4Switches off intermittent wiping
5Wipes with washer fluid
1. Switch the ignition switch to the ON position.
2. Turn switch
1on the combination switch to
the corresponding position.
When the rear window wiper is switched on,
the
symbol appears in the assistance
graphic in the combination meter. Further
information on the assistance graphic (see
Showing the distance display earlier in this
section). The defroster switch
Boperates when the
ignition switch is in the ON position for the rear
window, and (if equipped) for the outside rear
view mirrors.
The defroster is used to reduce the moisture,
fog or frost on the rear window surface and on
the outside mirror surface to improve the rear
view.
When the defroster switch
is pushed, the
indicator light illuminates and the defroster
operates for several minutes. After the preset
time has passed, the defroster will turn off
automatically. To turn off the defroster manu-
ally, push the defroster switch
again, and
the indicator light turns off.
NIC2617NAA1659
REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH
Instruments and controls2-61

Automatic headlight mode
is the preferred light switch setting. The
light setting is automatically selected according
to the brightness of the ambient light (excep-
tion: poor visibility due to weather conditions
such as fog, snow or spray):
•Ignition switch in ACC or ON position: the
side lights are switched on or off automati-
cally depending on the brightness of the
ambient light.
•With the engine running: if you have
switched on the daytime driving lights func-
tion in the vehicle information display, the
side lights and low beam headlights are
switched on or off automatically depending
on the brightness of the ambient light.
To switch on automatic headlight mode: turn the
light switch to .
WARNING
When the light switch is set to , the
low-beam headlights may not be switched on
automatically if there is fog, snow or other
causes of poor visibility due to the weather
conditions such as spray. There is a risk of an
accident
In such situations, turn the light switch to
. The automatic headlight feature is only an aid.
The driver is responsible for the vehicle lighting
at all times.
The daytime driving lights improve the detect-
ability of your vehicle during the day.
WARNING
When the daytime running light system is ac-
tive, tail lights on your vehicle are not on. It is
necessary at dusk to turn on your headlights.
Failure to do so could cause an accident injur-
ing yourself and others.
When the side lights and low-beam headlights
are switched on, the green
(side lights)
and(low-beam headlights) indicator
lights in the combination meter light up.
Low-beam headlights
When the ignition is switched on and the light
switch is in theposition, the side lights
and low-beam headlights are switched on even
if the light sensor does not sense dark ambient
light conditions. This is advantageous when
there is fog or rain.
To switch on the low-beam headlights:
•Switch the ignition switch to the ON position,
or start the engine.
•Turn the light switch to. The greenindicator light in the combination me-
ter lights up.
Side lights
NOTE
Always park your vehicle safely and sufficiently
lit according to legal standards. To reduce the
chance of a discharged vehicle battery, avoid the
continuous use of the
sidelights or park-
ing lights for several hours.
To switch on: turn the light switch to
. The
greenindicator light in the combination
meter lights up.
Parking lights
Switching on the parking lights ensures that the
corresponding side of the vehicle is illuminated.
To switch on the parking lights:
•The key is not in the ignition switch or the
switch is in the OFF position.
•Turn the light switch to(left-hand side
of the vehicle) or(right-hand side of
the vehicle).
2-64Instruments and controls

–Who have low intensity lighting, e. g.
cyclists.
– Whose lighting is blocked, e.g. by a bar-
rier.
•In very rare cases, High beam Assist recog-
nizes road users too late or not at all. In this,
or in similar situations, the automatic high
beam headlights will not be deactivated or
activated regardless. There is a risk of an
accident.
•Always carefully observe the traffic condi-
tions and switch off the high beam head-
lights in good time.
CAUTION
High beam Assist cannot compensate for road
and weather circumstances while driving. The
system saves the driver from having to operate
the switch. The driver always remains respon-
sible for choosing the correct light setting.
Specific situations in which to operate the
headlight switch manually:
•In heavy rain, snowy conditions. (general
poor visibility and bad weather conditions).
•When the vehicle sensors are dirty, covered
or broken.
Switching High Beam Assist on/off
To switch on:
Turn the light switch to and press the
combination switch beyond the pressure point
in the direction of arrow
3. Theindicator
light in the vehicle information display lights up
when it is dark and the light sensor switches on
the low-beam headlights.
If you are driving at speeds above approxi-
mately 28 MPH (45 km/h) the headlight range is
set automatically depending on the distance
between the vehicle and other road users.
If you are driving at speeds above approxi-
mately 34 MPH (55 km/h) and no other road
users are detected, the high beam headlights
are switched on automatically. The
indi- cator light in the combination meter also lights
up.
If you are driving at speeds below approxi-
mately 28 MPH (45 km/h) or other road users
are detected or the roads are adequately lit The
high beam headlights are switched off auto-
matically. The
indicator light in the com-
bination meter goes out. Theindicator
light in the vehicle information display remains
lit.
To deactivate
:
Move the combination switch back to its normal
position Theindicator light in the vehicle
information display goes out.
HEADLIGHTS MISTED UP ON THE
INSIDE
Certain climatic and physical conditions may
cause moisture to form in the headlight. This
moisture does not affect the functionality of the
headlight.
NIC2618
2-68Instruments and controls

POWER WINDOWS
WARNING
•Make sure that all passengers have their
hands, etc. inside the vehicle while it is in
motion and before closing the windows. Use
the window lock switch to prevent unex-
pected use of the power windows.
•To help avoid risk of injury or death through
unintended operation of the vehicle and or
its systems, including entrapment in win-
dows or inadvertent door lock activation, do
not leave children, people who require the
assistance of others or pets unattended in
your vehicle. Additionally, the temperature
inside a closed vehicle on a warm day can
quickly become high enough to cause a sig-
nificant risk of injury or death to people and
pets.
The switches for all side windows are located on
the driver’s door. There is also a switch on each
door for the corresponding side window The
switches on the driver’s door take precedence.
Auto-reverse function
The auto-reverse function can be activated
when a window is closed by automatic opera-
tion. Depending on the environment or driving condi-
tions, the auto-reverse function may be acti-
vated if an impact or load similar to something
being caught in the window occurs.
WARNING
There are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers have
their hands, etc., inside the vehicle before
closing the window.
If the vehicle’s battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate properly.
If this occurs, it is recommended you visit an
INFINITI retailer to re-initialize the power win-
dow auto-reverse system.
If the control unit detects something caught in a
window equipped with automatic operation as
it is closing, the window will be immediately
lowered.
Driver’s window switch
The power windows operate when the ignition
switch is in the ON position. 1. Front left side window
2. Front right side window
3. Rear left side window
4. Rear right side window
The driver’s switch, the main switch, can control
all windows.
•To open manually: press and hold the corre-
sponding button.
•To open fully: press the button beyond the
point of resistance to the second detent and
release it. Automatic operation is started.
•To close manually: pull the corresponding
button and hold it.
•To close fully: pull the button beyond the
point of resistance and release it. Automatic
operation is started.
NIC2715
WINDOWS
2-72Instruments and controls