2017 INFINITI QX30 ESP

Information command
1st command2nd command Action
Information Voice Menu Connects to the INFINITI InTouchTMServices Response Specialists. Refer to the Navigation Owner’s Manual for
details.
Operator Connects to the INFINITI InTouch
TMServices Response Specialists. Refer to the Navigation Owner’s Manual for
details.
Where am I?* Displays the information of the current position.
Fuel Prices Displays the fuel prices.
Weather Forecast Displays the weather forecast.
Current Weather Displays the nearby weather (current weather).
Sports Scores Displays the sports scores.
Traffic Information* Turns the traffic information system on or off.
Route Information* Displays the route information.
*: Models with navigation system only.
NOTE
The Fuel Prices, Weather Forecast, Current
Weather, Sports Scores and Traffic Information
will not operate without a subscription to
SiriusXM Radio.
VOICE RECOGNITION SETTINGS
Voice recognition functions can be set.
1. Push

iPod player
SymptomPossible cause Possible solution
The system does not recognize an iPod. The connector cable is not correctly connected or the iPod does not correctly operate.Connect the connector cable again. If the system
does not recognize the iPod after performing the procedure above, reset the iPod.
The iPod that is to be connected is not compatible with the system. Check the iPod model and firmware versions
available for the system.
The USB extension cable is not correctly connected. Do not use a USB extension cable.
The cable is rapidly connected to or disconnected from the USB connector. Slowly connect or disconnect the USB cable.
An iPod cannot be operated. The iPod is connected to the in-vehicle audio system
while headsets, etc. are connected to the iPod. Remove all equipment from the iPod after
disconnecting the iPod from the system, and then connect it to the system again.
The iPod is not operating normally. Disconnect and re-connect the iPod to the in-vehicle
audio system.
The system plays back an album/track that includes particular album art. Disconnect the iPod from the in-vehicle audio system
and then reset the iPod. Disable the album art and then re-connect the iPod to the system.
An iPod does not respond. There are too many tracks in a category. Decrease the number of tracks in a category (less
than 3,000 tracks).
The shuffle function is turned on. Turn off the shuffle function if many tracks are stored
on the iPod.
Music cannot be played back. The connector is not connected to the iPod. Firmly connect the connector until it clicks.
Music stops playing. The sound cuts off due to vibration resulting from the
iPod being in an unstable location. Place the iPod in a stable location where it does not
roll over.
The sound is distorted. The EQ (equalizer) function of the iPod is turned on. Turn off the EQ (equalizer) function.
The iPod battery requires more time than usual to charge. Charging the iPod battery may take longer while the
iPod is playing. If the iPod requires charging, it is recommended to
stop playback
4-128Display screen, heater and air conditioner, and audio system

BLUETOOTH® HANDS-FREE PHONE
SYSTEM
SymptomPossible cause Possible solution
A cellular phone cannot be registered. The cellular phone is not compatible with the in-vehicle hands-free phone system.Use a cellular phone compatible with the system. Visit the
website (www.infinitiusa/bluetooth) for model compatibility.
Registration of the cellular phone has been performed incorrectly. Check the registration procedure, and then register the
cellular phone again.
A cellular phone cannot be connected or
becomes disconnected after registration is complete. The Bluetooth® setting of the in-vehicle hands-free
phone system is turned off. Turn on the Bluetooth® setting of the system.
The Bluetooth® setting of the cellular phone is turned off. Turn on the Bluetooth® setting of the cellular phone.
The remaining battery level of the cellular phone is low. Charge the battery of the cellular phone.
The wireless Bluetooth® connection may be disrupted depending on the location of the cellular phone. Do not place the cellular phone in an area surrounded by
metal or far away from the in-vehicle hand-free phone
system. Do not place the cellular phone close to the seats or your body.
Registration of the cellular phone is not complete. Perform registration of the cellular phone.
A call to a particular phone number fails. If the system tries to make a call several times to the same phone number (for example: the party does notrespond to the call, the party is out of the network
service area, or the call is abandoned before the party responds), the system may reject a request to make a call to the phone number. Turn the cellular phone off and then on again to reset the
connection.
Display screen, heater and air conditioner, and audio system4-131

•Do not stop or park the vehicle over flam-
mable materials such as dry grass, waste-
paper or rags. They may ignite and cause a
fire.
CAUTION
•Do not use leaded gasoline. (SeeRecom-
mended fluids/lubricants and capacities in
the 9. Maintenance and Schedules sec-
tion.) Deposits from leaded gasoline seri-
ously reduce the ability of the three-way
catalyst to help reduce exhaust pollutants
and/or damage the three-way catalyst.
•Keep your engine tuned up. Malfunctions in
the ignition, fuel injection, or electrical sys-
tems may cause overrich fuel to flow into
the three-way catalyst, causing it to over-
heat. Do not keep driving if the engine mis-
fires, or if noticeable loss of performance or
other unusual operating conditions are de-
tected. Have the vehicle inspected
promptly. It is recommended you visit an
INFINITI retailer for this service.
•Avoid driving with an extremely low fuel
level. Running out of fuel could cause the engine to misfire, damaging the three-way
catalyst.
•Do not race the engine while warming it up.
•Do not push or tow your vehicle to start the
engine.
TIRE PRESSURE MONITORING SYSTEM
(TPMS)
Each tire, including the spare (if present),
should be checked monthly when cold and
inflated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your
vehicle has tires of a different size than the size
indicated on the vehicle placard or tire inflation
pressure label, you should determine the
proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pres-
sure telltale when one or more of your tires is
significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pres-
sure. Driving on a significantly under-inflated
tire causes the tire to overheat and can lead totire failure. Under-inflation also reduces fuel
efficiency and tire tread life, and may affect the
vehicle’s handling and stopping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver’s
responsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The TPMS
malfunction indicator is combined with the low
tire pressure telltale. When the system detects
a malfunction, the telltale will flash for approxi-
mately one minute and then remain continu-
ously illuminated. This sequence will continue
upon subsequent vehicle start-ups as long as
the malfunction exists. When the malfunction
indicator is illuminated, the system may not be
able to detect or signal low tire pressure as
intended. TPMS malfunctions may occur for a
variety of reasons, including the installation of
replacement or alternate tires or wheels on the
vehicle that prevent the TPMS from working
properly. Always check the TPMS telltale after
replacing one or more tires or wheels on your
vehicle to ensure that the replacement or alter-
nate tires and wheels allow the TPMS to con-
tinue to function properly.
Starting and driving5-5

tire depends on outside temperature, ve-
hicle load, road conditions and other fac-
tors.
– If you detect any unusual sounds or vi-
brations while driving with a punctured
run-flat tire, pull off the road to a safe
location and stop the vehicle as soon as
possible. The tire may be seriously dam-
aged and need to be replaced.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire (for models equipped with
the emergency tire puncture repair kit). It is
recommended you visit an INFINITI retailer
for this service.
•INFINITI recommends using only INFINITI
Genuine Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can
cause the tire to lose air pressure (for mod-
els equipped with the emergency tire punc-
ture repair kit).
CAUTION
•The TPMS may not function properly when
the wheels are equipped with snow chains
or the wheels are buried in snow.
•Do not place metalized film or any metal
parts (antenna, etc.) on the windows. This
may cause poor reception of the signals
from the tire pressure sensors, and the
TPMS will not function properly.
It is the driver’s responsibility to set the tire
pressure to the recommended cold tire pressure
suitable for the operating situation (see
Wheels and tires in the8. Do-it-yourself
section). Note that the correct tire pressure for
the current operating situation must first be
taught-in to the tire pressure monitor (see
Restarting TPMS later in this section).
If there is a substantial loss of pressure, the
warning threshold for the warning message is
aligned to the reference values taught-in. Re-
start the tire pressure monitor after adjusting to
the cold tire pressure. The current pressures are
saved as new reference values. This will ensure
that a warning message will only appear if the
tire pressure drops significantly. The tire pressure monitor does not warn you of
an incorrectly set tire pressure.
TPMS is not able to warn you of a sudden loss
of pressure, e. g. if the tire is penetrated by a
foreign object. In the event of a sudden loss of
pressure, bring the vehicle to a halt by braking
carefully. Avoid abrupt steering maneuvers.
TPMS has a yellow warning lamp in the combi-
nation meter for indicating a pressure loss or
malfunction. Depending on how the warning
lamp flashes or lights up, a tire pressure that is
too low or a malfunction in TPMS is indicated:
•If the warning lamp is lit continuously, the
tire pressure on one or more tires is signifi-
cantly too low. TPMS is not malfunctioning.
•If the warning lamp flashes for around a
minute and then remains lit constantly, the
TPMS is malfunctioning.
In addition to the warning lamp, a message
appears in the vehicle information display. Ob-
serve the information on display messages (see
Safety systems in the2. Instruments and
controls section
It may take up to ten minutes for a malfunction
of the tire pressure monitor to be indicated. A
malfunction will be indicated by the tire pres-
sure warning lamp flashing for approximately
one minute and then remaining lit. When the
Starting and driving5-7

Tire Pressure Monitoring System
warning messages
If the tire pressure monitor detects a pressure
loss in one or more tires, a warning message is
shown in the vehicle information display and
the yellow tire pressure monitor warning lamp
comes on.
•If the [Please Correct Tire Pressure] (yellow)
message appears in the vehicle information
display, the tire pressure in at least one tire
is too low and must be corrected at the next
opportunity. If the system detects that new
sensors have been fitted (IDs do not match
those stored, and the pressure is not fea-
sible, or is less than 14% under the norm
then the [Please Correct Tire Pressure] mes-
sage will be displayed in white.
•If the [Check Tires] (red) message appears in
the vehicle information display, the tire pres-
sure in one or more tires has dropped sig-
nificantly and the tires must be checked.
•If the [Warning Tire Malfunction] (red) mes-
sage appears in the vehicle information dis-
play, the tire pressure in one or more tires
has dropped suddenly and the tires must be
checked.
•If the [Tire Press. Sensor(s) Missing] mes-
sage appears in the vehicle information dis-
play, one or more sensors are missing or
cannot be detected. This could be the result
of fitting a replacement wheel/tire.
Observe the instructions and safety notes in the
display messages in the vehicle information
display.
If the wheel positions on the vehicle are inter-
changed, the tire pressures may be displayed
for the wrong positions for a short time. After a
few minutes of driving, this is rectified and the
tire pressures are displayed for the correct
positions.
Restarting TPMS
To keep the TPMS functioning properly, the
restart operation must be performed in the
following cases:
•When the tire pressure is adjusted
•When a tire or a wheel is replaced
•When the tires are rotated
When you restart the tire pressure monitor, all
existing warning messages are deleted and the
warning lamps go out. The monitor uses the
currently set tire pressures as the reference
values for monitoring. In most cases, the tire
pressure monitor will automatically detect the new reference values after you have changed
the tire pressure. However, you can also define
reference values manually as described here.
The tire pressure monitor then monitors the
new tire pressure values.
Perform the following procedures to restart the
TPMS.
NOTE
Before restarting, make sure that the tire pres-
sures are set properly on all four tires for the
respective operating conditions. The recom-
mended tire pressures can be found in the tire
pressure placard on the driver’ door pillar.
1. Make sure that the ignition switch is in the
ON position.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Tire Pressure].
4. Press to confirm. The vehicle information display shows the
current tire pressure for each tire or the [Tire
pressures will be displayed after driving a
few minutes] message.
Starting and driving5-9

If you wish to confirm the restart:
5. Press to confirm.The [Tire Press. Monitor Restarted] message
appears in the vehicle information display.
After you have driven for a few minutes, the
system checks whether the current tire pres-
sures are within the specified range The new
tire pressures are then accepted as refer-
ence values and monitored
If you wish to cancel the restart:
6. Press the
button.
The tire pressure values stored at the last
restart will continue to be monitored
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation. NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
ON PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher roll-
over rate than other types of vehicles.
They have higher ground clearance than pas-
senger cars to make them capable of perform-
ing in a variety of on-pavement and off-road
applications. This gives them a higher center of
gravity than ordinary vehicles. An advantage of
higher ground clearance is a better view of the
road, allowing you to anticipate problems. How-
ever, they are not designed for cornering at the
same speeds as conventional 2-wheel drive
vehicles any more than low-slung sports cars
are designed to perform satisfactorily underoff-road conditions. If at all possible, avoid
sharp turns at high speeds. As with other
vehicles of this type, failure to operate this
vehicle correctly may result in loss of control or
vehicle rollover. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt.
For additional information, refer to
Driving
safety precautions later in this section.
AVOIDING COLLISION AND ROLLOVER
WARNING
Failure to operate this vehicle in a safe and
prudent manner may result in loss of control or
an accident.
Be alert and drive defensively at all times. Obey
all traffic regulations. Avoid excessive speed,
high speed cornering, or sudden steering ma-
neuvers, because these driving practices could
cause you to lose control of your vehicle.
As with any vehicle, loss of control could result
in a collision with other vehicles or objects or
cause the vehicle to roll over, particularly if the
loss of control causes the vehicle to slide side-
ways. Be attentive at all times, and avoid
driving when tired. Never drive when under the
5-10Starting and driving

influence of alcohol or drugs (including pre-
scription or over the- counter drugs which may
cause drowsiness). Always wear your seat belt
as outlined in the “Safety – Seats, seat belts
and supplemental restraint system” section of
this manual, and also instruct your passengers
to do so.
Seat belts help reduce the risk of injury in
collisions and rollovers.In a rollover crash, an
unbelted or improperly belted person is signifi-
cantly more likely to be injured or killed than a
person properly wearing a seat belt.
OFF-ROAD RECOVERY
While driving, the right side or left side wheels
may unintentionally leave the road surface. If
this occurs, maintain control of the vehicle by
following the procedure below. Please note that
this procedure is only a general guide. The
vehicle must be driven as appropriate based on
the conditions of the vehicle, road and traffic.
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight
course.
4. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle. 5. If there is nothing in the way, steer the
vehicle to follow the road while vehicle
speed is reduced. Do not attempt to drive
the vehicle back onto the road surface until
vehicle speed is reduced.
6. When it is safe to do so, gradually turn the steering wheel until both tires return to the
road surface. When all tires are on the road
surface, steer the vehicle to stay in the
appropriate driving lane.
If you decide that it is not safe to return the
vehicle to the road surface based on vehicle,
road or traffic conditions, gradually slow the
vehicle to a stop in a safe place off the road.RAPID AIR PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged due
to hitting a curb or pothole. Rapid air pressure
loss can also be caused by driving on under-
inflated tires.
Rapid air pressure loss can affect the handling
and stability of the vehicle, especially at high-
way speeds.
Help prevent rapid air pressure loss by main-
taining the correct air pressure and visually
inspect the tires for wear and damage. For
additional information, refer to “Wheels and
tires” in the “Maintenance and do-it-yourself” section of this manual. If a tire rapidly loses air
pressure or “blows-out” while driving, maintain
control of the vehicle by following the proce-
dure below. Please note that this procedure is
only a general guide. The vehicle must be driven
as appropriate based on the conditions of the
vehicle, road and traffic.
WARNING
The following actions can increase the chance
of losing control of the vehicle if there is a
sudden loss of tire air pressure. Losing control
of the vehicle may cause a collision and result
in personal injury.
•The vehicle generally moves or pulls in the
direction of the flat tire.
•Do not rapidly apply the brakes.
•Do not rapidly release the accelerator pedal.
•Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering wheel with both hands and try to hold a straight
course.
3. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle.
Starting and driving5-11